Maytag Range / Cooktop / Oven Parts

Ordered main control board and top blower. parts arrived as expected and well packaged. replaced main control board. Took two times to get ribbon cable inserted and aligned correctly. display functioned properly, but blower still not turning. replaced upper blower. everything working now. Read more

It was a simple process to enter the model number of our glass cook top stove; learn the part number required and order. It arrived in 2-days -- least expensive shipping method. The cooktop was removed with a Phillips-head screwdriver by 4 small sheet metal screws on the right and left side of the oven. The oven's power to the cooktop was easily disconnected via two "clips" and one ground. Would have cost way more with an appliance repair shop and it's an easy do-it-yourself repair. Read more

, shut gas valve to range, unplug from wall outlet, ordered thermostat. less then 30 minutes to install new thermostat, range back to normal function Read more

• Little to no heat when broiling
• Element will not heat

Turned off breaker to oven, took pictures of existing broil, supporting bracket and shield attached to oven, removed screws holding element, support piece and shield, removed bracket and shield, pulled out the element, took another close-up picture of the wires connected to element, removed wires, connected new element, turned breaker on to see if connection is correct, turned it off, installed element, shield and support bracket (in this order). Turned breaker on. Hardest part was loosening... Read more

I knew for sure that the hinge with the large spring was damaged, but elected to replace both hinges and receivers. Replacing the parts was fairly easy and would have taken me less then an hour. This model has thin metal covers over the hinge assemblies. I found that squeezing in the sides of the covers help to hold them in place on the hinge while reassembling the door. My only difficulty was putting the door back on the oven. It took a little maneuvering but I managed to get it. Now the door... Read more

Replaced the control that I think was bad from the purchase of the stove new as the burner didn’t throttle as is does now. Read more

Just removed the old glass top which consisted of removing 6 screws Read more

I purchased a burner and a oven orifice replacement kit from Appliance Parts Pros. I downloaded an installation manual from Whirlpool and followed the instructions. It was pretty easy. The front burner orifices could be replaced by just taking off the burner cover. The back ones required removing the burner diffuser. You will need to reattach the back burner bottom assembies after you remove the diffuser before you unscrew the orifice or it might bend the burner piping causing it to not line up... Read more

First and foremost I UNPLUGGED THE OVEN!. I'll pass on the early morning SHOCK THERAPY! Second, I unscrewed aluminum protection plate from back of oven. Next, I unplugged the two connections behind the oven switch. Then I removed the plastic switch from the front and unscrewed the two screws that secured the oven switch to the oven. Once you've completed all these steps you take your new oven switch and do everything again but in reverse order. Hope this was informative, direct, and that your... Read more

• Little to no heat when broiling

I wanted to get the upper oven baking element replaced; it hasn't been working for a few months. This double oven has had two other issues, there is a fan that comes on to cool the electronics panel, That fan has made excessive noise and it operates for 2-3 hours after the oven turns off. The other problem with the oven is the Self-Cleaning feature runs for about 15-30 minutes and then turns off with an error code. I've had a local appliance repair person in to address the error code and... Read more

• Element will not heat

Purchased a new Element surface and installed same... All Okay now... Read more

These are very easy to replace ,just gave the old one a quarter turn lifted it out took the two wires off (noted where each one will go on the new burner ) pop the wires onto the new burner put it on and good to go. Read more

• Little to no heat when broiling

Ordered a new one. Read more

• Door won't open or close

I replaced the hinge due to the hinge spring breaking. To replace the hinge you do the following: 1. Disconnect power to stove, either at circuit box or at outlet. 2. Lift door off of outside hinge arms ; no screws are used to attach the door to the hinge 3. Remove two screw on under side of cook top, one on each side. 4. Disconnect cook top connector. 5. Lift cook top off 6. Remove screws from top rail of stove that hold the side panel. 7. Remove the screw on the back that hold the side... Read more

• Won't start

First, it was going to cost $95 for an appliance guy just to look at it! I figured there would be an upcharge on the parts + labor on top of the $95, so I took a chance & decided my husband & I could fix it cheaper; we were right, but it was a 3 week process (luckily, we have another microwave in the basement we were able to use in the meantime). I googled the microwave model #, then price checked the same item I thought we needed; printed off the diagrams of the various microwave "systems" &... Read more

Little procrastination paid off. With only 50% capability I knew it is time to call the appliancepartspros. They shipped me parts within 3 days. It was practical to fix both at the time. All I needed was to disconnect power at range breaker box, grab a screwdriver to lift top open, a 16 inch or so piece of old 2×4 wood to keep the top top of stove lifted, so I could access heating elements from underneath. Then I took my black sharpie And marked location of mounting screws and... Read more