Need Help?
Call
Replacement actuator pad for refrigerator water and ice dispensers. Snaps into dispenser panel. Replace if cracked, broken, or tabs are damaged.
Super easy fix, remove two screws behind drop tray, unplug the wiring harness to dispenser, unplug and remove old pad, then snap new one into place. Reconnect harness. Took less than 5 minutes, works like new. Read more
Replacement drip tray for refrigerator water and ice dispenser. Installs below dispenser opening. Replace if cracked, warped, discolored, or missing.
After using the crushed ice feature on my KitchenAid French Door refrigerator, the ice maker wouldn't stop dispensing ice, crushed or cubed. I thought it had to do with the paddle switch being stuck or something else in the door, but all door components seemed to be working as intended. I ended up pulling the ice maker out and disconnecting the wires to the auger so that I could leave the refrigerator plugged in. I call AppliancePartsPros.com the following morning and explained my situation.... Read more
Black grille that sits at the base of your refrigerator's ice/water dispenser to catch drips. Replace when cracked, stained, loose, or missing.
Bought a replacement overflow grille. Read more
Covers and protects the ice container in your refrigerator. Replace if cracked, broken, or missing to keep ice fresh and prevent contamination.
White plastic grille that sits beneath the ice and water dispenser to catch drips and spills. Replace if cracked, stained, or missing for a clean look.
The new Ui assembly that has all new push buttons. I found the water shutoff and the power plug when we pulled the fridge out. I shut off the water and pulled the AC plug. The whole assembly that is being replaced, came out easily when I pushed two small tabs on the lower part of the old asm bottom left and right. I used a small screwdriver to release one and then the other tab. I disconnected the electrical connector and the old unit was free. Connect the power plug to the new unit and slide... Read more
Channels ice from maker to dispenser opening. Replace if cracked, broken, or missing to prevent ice scatter and jams. Installs in freezer door dispenser.
Identified and ordered part Read more
White overflow grille for refrigerator water/ice dispenser. Replaces cracked, pitted, discolored, or missing grilles. Snaps into place below dispenser.
I found the part I needed through AppliancePartsPros.com. The price was far more than I wanted to spend, but my wife kept asking me to get a replacement. "Any port in a storm" as the old saying goes. I'm keeping it clean for the time being. When company comes over, I'll put it in to make the refrigerator look good. Read more
Color: black. Measures about 10 inches wide by 4 inches deep.
I replaced the water inlet valve & both dispenser levers (water & ice) and adjusted the lever locking spring. Read more
This ice door motor drives the dispenser flap that opens for ice dispensing and closes to seal the chute. Replacing a weak or failed motor restores smooth door movement and helps prevent warm air and moisture from entering the freezer. What it does:
I replaced the ice door motor with new hardware, circuit board on touch panel display then the main ECB on top in the doghouse. It finally came to life and started working! No issues with the front panel and everything works as it did! Read more
Color: White. Size: 3 3/8 inches in diameter. This is the door chute located in the freezer door on your refrigerator.
Replaced the door flap...repair went very well. Read more
Color: black. It measures about 10 inches wide by 4 inches deep.
Appliances came with the house we recently purchased, but there were a few parts on the Jenn Aire refrigerator. It looked terrible! It was super-easy to locate the pieces I needed, but honestly I was not confident they would fit. But they did, and perfectly! My refrigerator looks brand new. If I ever need parts or to make a repair, this will be the first place I will turn. Thank you! Read more
Dispenser facade cracked or discolored? This trim assembly restores your refrigerator's dispenser appearance and proper fit. Straightforward install.
Dispenser funnel guide ice door for side-by-side refrigerators. Guides ice from door dispenser into your glass. Replace if cracked, broken, or damaged.
Fix leaking or improper detergent dispensing caused by cracks or mineral buildup. This washer dispenser tank restores proper detergent flow.
Ice maker not filling properly or water leaking in freezer? A cracked fill cup causes inconsistent fills and leaks. Simple DIY fix guides water correctly.
I SAW THE VIDEO AND WAS SO EASY THAT MY CHILDREN COULD DO IT Read more
Usually ships within 4 - 14 days
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.