Maytag Refrigerator Dispenser Parts

• Ice maker dispenses too much ice

Ice Door Kit, Control Bracket, and Ice Dispenser Guide were purchased. I followed two videos on replacing the parts. The Control Bracket WP2180226 / AP6005965, was straight forward and I discovered a snapped pin on the old bracket causing an electric switch to be out of place... that repair was easy. When it came to the hinges of the ice chute, I discovered the snap-in, on right side, of the hinge was cracked... this is why the pin escaped. This cracked part is molded into the entire... Read more

Finding the part was puzzling. AppliancePros had the relevant manufacturer's part schematics handy on-line through which I quickly identified and order the replacement part. But the best aspect was AppliancePros' Amazon-like excellence in a) pricing and b) swift delivery (with precious tracking included). Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

Replaced the actuator pad on the Whirlpool Gold Series, releasing the electronic menu pad to get to the water activator pad was the biggest hurdle. The release tabs are underneath the menu pad and you may feel as if you may break them when releasing them. They did not break but I did hold by breath. Read more

Order part and replaced switch. Read more

• Door sweating
• Ice maker won't dispense ice

We ordered the Ice Door Fountain Kit and ice door spring, which was delivered to our home within three or four days. I understood everything about how to change it except the placement of the spring. A video on your website showed exactly how to put the spring in place and helped me get the job done quickly. It solved our problem and we really appreciate your services. Read more

The tray just sits in a slot on the door so no tools required Read more

Once the parts arrived, I followed the help video that was emailed to me with my order confirmation step by step. Super useful! The video quality and editing were well done and the instructions were very specific. I felt like a pro! Read more

I replaced the Ice Dispenser Lever. Since the replacement part is only available in white and my fridge is bone, I replaced also the Water Dispenser Lever, so it looks much better. I followed the instructions in the video, which were very useful and very well done. My problem was that the refrigerator is a KitchenAid built-in, while the instructions were for a Whirlpool, so the removal of the faceplate was quite different from what was shown in the video and more difficult. Also there were some... Read more

Ordered part, it fit perfectly! Read more

I bought the complete ice chute. It was easy to install and it works perfectly now. Many thanks. Read more

Removed water catcher, then 4 screws in water/ice vault in door, then removed screws on door side (5) top (2) and bottom (2). Removed stainless door skin. Removed 4 hex head bolts in ice/water vault (containing pads) and 4 bolts on the module immediately above the vault. Pulled the vault and module above out part way to unplug one cable. Then laid on table to unplug pads. From back, each pad has a small indent preventing the pad from being pushed up and removed. Push the small indent with a... Read more

Ordered the parts. Watched a great video on this web site. Installed. Fixed. Easy peesey. Read more

Super easy fix, remove two screws behind drop tray, unplug the wiring harness to dispenser, unplug and remove old pad, then snap new one into place. Reconnect harness. Took less than 5 minutes, works like new. Read more

After using the crushed ice feature on my KitchenAid French Door refrigerator, the ice maker wouldn't stop dispensing ice, crushed or cubed. I thought it had to do with the paddle switch being stuck or something else in the door, but all door components seemed to be working as intended. I ended up pulling the ice maker out and disconnecting the wires to the auger so that I could leave the refrigerator plugged in. I call AppliancePartsPros.com the following morning and explained my situation.... Read more