Maytag Washer Pump

Restore proper draining with this complete drain pump assembly. It moves water out of the washer during the drain and spin portions of the cycle to prevent standing water, cycle interruptions, and musty odors.

• Pumps wastewater from the tub to the household drain
• Helps prevent standing water and cycle pauses
• Common symptoms: won't drain or drains slowly, humming or grinding from the pump area, leaks at the pump, drain-related error codes
• Direct replacement for a failed or noisy pump assembly

• Disconnect power and shut off water before servicing; have towels or a pan ready for residual water
• Access location varies by model; remove the appropriate lower/front/rear panel to reach the pump
• Transfer wiring and hoses one at a time to the new pump, matching orientation; securely seat clamps and seals
• Inspect and clear the drain hose and filter for debris before reassembly; run a test cycle and check for leaks

The Drain Pump Assembly is an OEM part for Whirlpool washing machines. This part is responsible for removing water from the washer during the drain cycle. 

Causes of a bad drain pump assembly can include blockages from debris, wear and tear on the pump motor, or damage from objects accidentally left in pockets.  

Symptoms of a bad drain pump assembly include:

• The washer not draining water
• Water remaining in the tub after a cycle
• Unusual noises during the drain cycle
• Error codes related to draining issues

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This water pump assembly circulates water through the appliance during active cycles. It restores proper water movement when the original pump becomes weak, noisy, or fails, helping maintain consistent washing performance and coverage. What it does

• Circulates water through the internal system as designed
• Helps distribute detergent and cleaning action evenly
• Symptoms of a failing pump include little/no water movement and poor wash results
• May produce loud humming/grinding from the pump area or show small leaks
• Some models may display error codes related to water circulation

• 1 water pump assembly

• Disconnect power and shut off water before servicing
• Access location varies by model; remove panels as needed and prepare for residual water
• Transfer hoses and clamps to the new pump; ensure tight, leak-free connections and correct orientation
• Reconnect wiring securely, then run a test cycle and check for leaks

This quality drain pump is designed to fit washing machines. It's an internal part that is tasked with removing the water that is in the tub during the spin cycle. The pump forces the water in the bottom to go up into the drain hose. The hose loops up to the top of the washing machine and then down to the drain so the tub can easily fill. If the pump is starting to fail, a humming noise may be present.If the washing machine drain pump needs to be replaced, unplug the appliance from the wall or turn off the circuit breaker. The water source should also be turned off throughout the process. Remove the washer face to get access to the drain pump. The pump is typically in one of the corners, where it can be inspected before any clogs are removed. Disconnect the part and replace it with the new drain hose.This drain pump is made to work with several washing machines by Maytag. It is sourced directly from the manufacturer as a genuine OEM replacement part. The component is priced individually.

This circulation pump recirculates water through the spray arms during the wash and rinse cycles. Replacing a failing pump restores proper wash pressure and helps resolve poor cleaning, no-spray conditions, and loud humming from the motor.

• Recirculates water from the sump through the spray arms to clean dishes
• Maintains correct water flow and pressure during wash/rinse
• Common symptoms: tub fills but no spray action, poor cleaning results, loud humming/rumbling or grinding from the pump area, cycle stalls or runs long
• Restores consistent wash performance when the original pump motor has failed

• Disconnect power and shut off the water supply before service
• Access is from the bottom/front; remove the toe-kick and lower panels as needed
• Expect some residual water—use towels or a shallow pan
• Ensure the pump O-ring seats correctly; secure clamps/connectors and run a leak check after reassembly

This drain pump assembly moves water out of the appliance during the drain portion of the cycle. Replacing a weak or failed pump restores proper draining and helps prevent standing water, odors, or repeated drain attempts.

• Actively pumps wastewater through the drain hose to household plumbing
• Engages during the drain step to clear the tub/sump between and after cycles
• Typical failure symptoms: won't drain or drains slowly; water left in the bottom; loud humming/grinding during drain; leaks around the pump area
• May fail due to worn motor, damaged impeller, or debris lodged inside the pump

• Disconnect power and turn off water supply; bail or wet-vac any standing water before starting
• Keep towels or a shallow pan ready; clamp or plug hoses to control residual water
• Transfer hose connections and any mounting hardware from the original pump; ensure seals and clamps are seated firmly
• After installation, run a short cycle to check for leaks

This drain pump assembly removes wastewater from the washer during the drain and spin portions of the cycle. Replacing a weak or failed pump helps the washer finish cycles without standing water, odors, or error interruptions.

• Pumps water from the tub to the household drain during drain/spin
• Wet clothes at cycle end, or humming/grinding noises from the pump area
• Leaking around the pump or connections can indicate a cracked housing

• Disconnect power and shut off water supply before servicing
• Expect some water release; place towels or a shallow pan under the pump
• Transfer wires and hoses to the new pump in the same orientation; reuse existing clamps
• Inspect hoses/filters for obstructions and run a quick drain test to check for leaks

This replacement filter traps debris and contaminants within your appliance's system to help protect internal components and maintain proper performance. Swapping a clogged or damaged filter can restore flow/airflow, reduce odors and buildup, and support efficient operation. What it does:

• Captures grease, lint, dust, or food particles to prevent recirculation and protect internal parts
• Supports proper airflow or fluid flow for ventilation, circulation, or drainage
• Helps minimize odors and residue caused by a saturated filter
• Typical signs it's due: visible tears/warping, heavy buildup, restricted airflow/venting, lingering odors

• 1 filter

• Disconnect power before servicing and allow any hot surfaces to cool
• Note the filter's orientation and any tabs/clips; install the new filter the same way
• Clean the surrounding housing or channel before installation
• Do not operate the appliance without required filter(s); follow your model's maintenance schedule

This drain pump assembly moves water out of the washer during the drain and spin parts of the cycle. Replacing a weak, noisy, or leaking pump restores proper draining, prevents standing water, and helps cycles finish correctly.

• Pumps wastewater from the tub to the household drain
• Supports proper spin performance by clearing water from the tub
• Common symptoms: won't drain or drains slowly; water left in tub; loud humming/grinding from pump area; leaks around the pump; cycle stops with a drain-related error
• A clogged hose or debris in the pump can mimic failure—inspect for obstructions

• Disconnect power and water supply; wear gloves. Bail or wet-vac remaining water and place towels or a pan to catch spills
• Clamp and remove inlet/outlet hoses; note hose orientation and routing
• Move wiring connector(s) one at a time to the new pump and secure the pump in place
• Ensure hoses are clear and clamps tight; run a drain/spin test and check for leaks

This is the water pump that moves water through your appliance so cycles can run correctly. Replacing a failing pump restores proper water flow and helps prevent standing water, poor performance, and leaks. What it does:

• Circulates and/or removes water as the appliance operates
• Supports proper flow so wash/rinse/drain steps can complete
• Maintains a sealed path at the pump connections to help prevent leaks
• Typical symptoms of a failing pump: standing water, weak/no water movement, loud humming or grinding from the pump area, leaks, or related drain/circulation errors

• 1 water pump

• Disconnect power and shut off water supply before servicing
• Have towels/containment ready; some residual water is normal when hoses are removed
• Move wires and hoses one-for-one to the new pump; tighten clamps and check any O-rings/seals
• Run a short test cycle and inspect for leaks and proper water movement

This water pump moves wastewater out of the appliance so cycles finish and the tub stays clear of standing water. It replaces a failed pump to restore normal draining and cycle completion. What it does

• Pumps out drain water so the appliance can complete wash or rinse cycles
• Stops leaks from a damaged pump housing or worn seals
• Common symptom: appliance won't drain or has standing water after a cycle
• Can reduce or stop unusual grinding or humming noises coming from the pump area

• Disconnect power and water supply before beginning any repair
• Inspect hoses and seals for damage and replace if necessary when changing the pump
• Install with correct mounting orientation and secure electrical connections per OEM instructions