Maytag Washer Support Parts

The Shock Absorber Washer is an OEM replacement part specific to Whirlpool-brand washing machines. It is a hydraulic device that absorbs the vibrations of the outer washer tub. Note: This is only one shock absorber.

Symptoms of worn or cracked shock absorber washers include:

• Noisy operation as the washer shakes or moves during cycles
• Physical signs of deterioration
• Over time, increased stresses can damage connected components

Causes involve many cycles of compression and release and solvents inside the washer degrading natural rubber. Deteriorated washers no longer absorb vibrations properly.  

This part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Shock Absorber Kit is an OEM part for Whirlpool washing machines. This kit includes 4 shock absorbers designed to reduce vibrations and absorb shocks during the washing and spinning cycles, providing stability and minimizing excessive movement of the washer drum.

Causes of a bad shock absorber can include wear and tear from regular use, exposure to heavy loads or unbalanced loads that put excessive strain on the absorbers, or damage due to impact or mishandling.

Symptoms of a bad shock absorber kit include:

• Excessive shaking or vibrating during the wash cycle
• Loud banging noises
• The washer moving or "walking" during operation
• Leaks due to increased stress on the tub and other components

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This washer suspension rod kit supports and steadies the tub so your machine can spin smoothly with less vibration and noise. Replacing worn suspension helps reduce banging, off-balance interruptions, and wet loads after spin. What it does:

• Supports and centers the wash tub within the cabinet
• Dampens movement to reduce shaking, thumping, and "walking"
• Helps the washer reach and maintain proper spin speed
• Resolve UL/unbalanced errors, excessive vibration, and a tub that sags or leans

• Four suspension rods with pre-attached springs

• Disconnect power and water; move the appliance to access service panels safely
• Lift the top/remove the cabinet; support the tub during service
• Replace rods one at a time to keep the tub supported; match any color-coded positions
• Level the washer after reassembly; perform calibration/diagnostics if the model requires it

The Suspension Rod Kit is an OEM part for Whirlpool washing machines. This kit includes suspension rods that are designed to support and stabilize the washing machine tub during the wash and spin cycles. 

Causes of a bad suspension rod can include regular wear and tear, overloading the washing machine, or damage from heavy loads that place excessive stress on the rods. 

Symptoms of a bad suspension rod include:

• Excessive shaking or vibrating during the wash or spin cycles
• Loud banging or knocking noises during operation
• The washing machine tub being off-balance or leaning to one side
• The washer moving or "walking" across the floor during use

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This washer shock absorber helps control tub movement during spin and agitation. Replacing a worn damper restores stability, reduces vibration, and helps prevent excessive noise and shaking during cycles.

• Controls suspension movement to keep the tub steady
• Helps reduce banging, walking, and excessive vibration
• Can alleviate loud thumping or rattling during spin
• Supports smoother, quieter operation when shocks wear out

• Unplug washer and turn off water supply before servicing
• Access from front or rear panel varies by model; support the tub to relieve tension
• Replace in matched positions; some washers use multiple shocks
• Each end is fully seated and locked before reassembly

The Shock Absorber is an OEM part compatible with Whirlpool washing machines. It is a crucial component that helps reduce vibrations and dampens movement during the spin cycle. The shock absorber absorbs mechanical stresses to prevent the washer tub, suspension springs, and other components from wearing out prematurely.  

Causes of a bad shock absorber include wear and tear over time, cracks or breaks from heavy loads, or damage due to impact.  

Symptoms of a bad shock absorber include:

• Excessive shaking, vibration or noise during the wash and spin cycles   
• The washer walking or moving during operation
• Premature failure of other suspension parts like springs or the washer frame
• Potential leaks if movement stresses plumbing connections

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

Includes suspension pads.

The Strap is an OEM part for Whirlpool washing machines. It is a component located inside the washer tub that holds onto and spins the outer tub during the wash cycle. The strap washer plays an important role in securing the outer tub in place while continuously channeling rotational force to drive the washing action and clean clothes effectively. 

Causes of a bad strap can include wear and tear from years of use, damage due to impact or mishandling, or degradation from chemical exposure. 

Symptoms of a bad strap include:

• Excessive vibration or shaking during spin cycles
• Noise or grinding sounds coming from the washer tub area 
• The outer tub wobbling or moving more than usual
• Uneven agitation that fails to thoroughly clean all clothes

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This backup plate is a stamped mounting support that helps secure and stabilize a refrigerator/freezer component, restoring proper alignment and reducing unwanted movement. It's a simple replacement part for worn or damaged mounting hardware. What it does

• Provides a stable mounting surface to hold components in place and prevent shifting.
• Restores proper alignment to assemblies that rely on a backing plate for support.
• Helps reduce vibration, rattling, or intermittent contact caused by a loose or damaged plate.
• Used when the original plate is bent, cracked, corroded, or otherwise compromised.

• Disconnect power to the appliance before beginning any repair.
• Inspect surrounding fasteners, brackets, and seals; replace any additional damaged hardware.
• Use appropriate hand tools; avoid overtightening fasteners that could deform the plate.