Microwave Fuse Or Sensor

This fixed thermostat senses temperature and opens or closes the electrical circuit to control heating. It replaces a failed temperature-sensing switch to restore proper heating control and safety. What it does:

• Monitors appliance temperature and interrupts power when the set limit is reached
• Prevents overheating by opening the circuit at high temperatures
• Restores normal heating control when a failed thermostat causes no heat or continuous heating
• Works as a safety/limit device in the appliance's heating system

• Disconnect power to the appliance before starting any repair
• Handle the thermostat and sensing element gently; avoid bending or stressing terminals
• Refer to the appliance service manual or OEM instructions for proper placement and mounting

This thermostat cavity is the molded housing that holds the oven thermostat sensor in place, keeping the sensor positioned for accurate temperature sensing. Replaces a worn or cracked housing to help restore proper sensor alignment. What it does:

• Secures the thermostat sensor/tube so the oven can monitor internal temperature reliably
• Protects the sensor from direct contact with heat sources and food debris
• Helps maintain consistent sensor placement after panel removal or repairs
• Common symptom: oven temperature reads incorrectly or cycles improperly when the housing is damaged

• Disconnect power to the appliance before beginning any repair
• Requires removal of the control panel or rear access panel depending on model; keep fasteners organized
• Handle gently to avoid cracking the new housing; inspect surrounding clips or tabs and replace if broken

This thermostat controls oven/dryer temperature by opening or closing its contacts as the appliance reaches set temperatures, helping maintain safe and consistent operation. Replaces a worn or failed thermostat to restore proper temperature regulation. What it does:

• Senses temperature and interrupts heating when limits are reached to prevent overheating
• Re-establishes heating when temperature falls, maintaining normal cycle performance
• Commonly installed when an appliance won't heat, overheats, or cycles erratically
• Works as a direct replacement for the OEM thermostat designed for compatible LG units

• One thermostat

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Note wire locations or take a photo before removing wiring; reconnect wires to the same terminals
• Use a multimeter to verify thermostat continuity and correct operation before and after replacement

This magnetron thermostat assembly helps prevent magnetron overheating by opening the circuit when temperatures get too high, protecting microwave components and helping restore normal operation once cooled. Fits the OEM thermostat function for safe thermal control. What it does:

• Senses excessive magnetron temperature and interrupts power to prevent overheating
• Helps stop microwave heating when the magnetron runs too hot or thermal limits are exceeded
• Common symptom: microwave powers on but does not heat or intermittently fails to heat
• Restores normal operation after cooling if no other faults are present

• Disconnect power and fully discharge the high-voltage capacitor before servicing
• Replace only with the correct OEM thermostat assembly to ensure proper fit and safety
• Handle with care; avoid shorting contacts or damaging terminal connections

This thermal fuse stops excessive heat build-up by opening the circuit when temperatures get unsafe, protecting the appliance and its heating components. Replace a failed fuse to restore normal heating and safety functions. What it does

• Opens the circuit if overheating is detected to prevent damage or fire risk.
• Prevents the heating element or motor from running when the fuse is blown.
• Common symptom: appliance fails to heat or runs but produces no heat.
• Common symptom: appliance does not start or suddenly stops during a heat cycle.

• One thermal fuse.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Replace with the exact OEM part number; improper substitutes may cause malfunction or safety issues.
• Inspect surrounding wiring and heating components for faults that could cause repeated fuse failures.

This thermostat controls refrigerator temperature to help maintain proper cooling and prevent spoilage. It replaces a failed or inaccurate temperature control to restore consistent operation. What it does:

• Senses internal temperature and signals the compressor to cycle on/off
• Helps keep food at steady, safe temperatures when functioning correctly
• Commonly replaces thermostats that cause warm temperatures or inconsistent cooling
• Works as a direct replacement when matching the OEM part number

• Always disconnect power to the appliance before servicing to avoid shock or injury
• Handle the sensor and terminals carefully; avoid bending or damaging components
• Basic hand tools are typically required; follow your model's service manual for exact instructions

This temperature control thermostat senses and regulates refrigerator temperature to keep food cold and appliances running efficiently. It replaces a worn or faulty controller to restore proper cooling cycles and temperature stability. What it does:

• Senses cabinet temperature and tells the compressor/evaporator fan when to run
• Restores normal cooling if a failed thermostat causes warm temperatures
• Stops continuous running or short-cycling when the thermostat was the issue
• Helps prevent food spoilage by maintaining consistent temperatures

• Disconnect power before servicing to avoid shock or injury
• Handle terminals and sensing elements carefully; avoid kinking or damaging capillary tubing
• Access may require removing interior panels or control housing—refer to your service manual

This oven thermostat senses and regulates the oven temperature so food cooks evenly and stays at the set temperature. It replaces a failed or inaccurate temperature control to restore proper oven heating. What it does:

• Monitors oven temperature and signals the burner/elements to cycle on and off
• Helps maintain set cooking temperatures for consistent baking and roasting
• Can correct symptoms like oven running too hot or too cold, or temperature that won't stabilize
• Works with the oven's control system to ensure accurate temperature regulation

• One oven thermostat

• Disconnect power (and shut off gas supply for gas ranges) before servicing
• Handle thermostat sensing bulb and capillary tube carefully; avoid kinks or sharp bends
• Reinstall to the original mounting and verify sensing bulb placement for accurate readings