Microwave Tray & Related

Supports the removable wire rack inside your microwave cavity. Replace this holder if cracked, broken, or missing to restore stable two-level cooking capability.

Connects the motor to the glass tray for smooth turntable rotation. Replace if your shaft is broken, worn, or causing the tray to wobble or scrape.

Replacement glass turntable tray for your microwave. Installs on the rotating support hub inside the cavity. Order when cracked, shattered, or broken.

This replacement tray catches and channels water under the refrigerator to prevent leaks and allow proper evaporation. It restores proper drainage and helps avoid standing water that can cause odors or damage. What it does

• Collects defrost and condensate water from the evaporator area to prevent puddling under the cabinet
• Directs water toward the evaporator/drain system so it can evaporate safely
• Helps keep the refrigerator floor and surrounding cabinetry dry
• Stops common symptoms like water pooling beneath the unit or musty smells from standing water

• One replacement tray

• Disconnect power to the appliance before any service
• Remove lower kick panel or shelves as required to access the tray; allow any standing water to drain into a bucket
• Inspect mounting location and drain channel for debris; clean before installing the new tray
• Seat the tray fully and restore panels; plug in and check for proper drainage during the next defrost cycle

This is a nonstick metal grill tray designed for use in a microwave or combination cooking appliance. It serves as a cooking surface that allows grease and drippings to drain away from food during grilling or broiling functions. Replace this tray if the nonstick coating is peeling, the metal is warped, or the grill no longer sits properly on the turntable.

Connects the turntable motor to the drive shaft in your microwave. Replace if cracked, broken, worn, or fused to the motor, preventing turntable rotation.

This is a support piece that sits on the microwave floor and connects to the turntable motor, allowing the glass tray to rotate during cooking. It acts as a drive coupling between the motor shaft and the turntable. Replace this support if your glass tray wobbles, does not rotate, or the coupling tabs are cracked or worn.

Replacement drive coupler for microwave turntable systems. Connects motor to turntable shaft. Replace if cracked, stripped, or broken to restore rotation.

This wire rack assembly provides a sturdy, removable shelf for your oven, giving stable support for cookware and bakeware and restoring proper shelf placement and clearance. What it does

• Replaces a bent, damaged, or missing oven shelf so pots and pans sit level during baking and roasting
• Restores smooth sliding and correct clearance for consistent cooking results
• Helps prevent cookware from tipping or shifting on weakened racks
• Fits into existing rack supports or side rails for secure positioning

• Remove power to the appliance and allow it to cool completely before installing
• Slide the rack into the oven rails or supports until fully seated; it rests level
• Wear gloves to avoid pinches or sharp edges while handling the rack
• No special tools usually required; refer to your owner's manual for model-specific guidance

Nonstick grille tray pan for microwave ovens with broiling/grilling capability. Replace your cracked, worn, or missing tray for even cooking results.

This glass tray is a flat oven shelf that provides a smooth, easy-to-clean surface for baking and roasting. It restores a stable cooking surface and replaces cracked, chipped, or otherwise damaged oven glass trays. What it does:

• Supports bakeware and cookware for even heating on the oven floor or shelf area
• Replaces trays that are cracked, chipped, or shattered and may cause uneven cooking
• Provides a smooth, non-porous surface that's simple to wipe clean
• Helps prevent food drips from contacting the oven floor when used as intended

• One glass tray

• Handle carefully; glass can break and cause injury—wear cut-resistant gloves
• Allow the oven to cool completely before removing or installing the tray
• Inspect tray for chips or stress cracks before first use; do not use if damaged
• Follow the appliance manufacturer's instructions for placement and safe use

Turntable roller assembly support for microwaves. Holds and guides the glass tray as it rotates. Replace if cracked, broken, or worn from use.

This guide supports the glass turntable tray inside the microwave, allowing it to rotate smoothly during cooking. It sits on the microwave floor and holds the tray at the correct height for even heating. Replace this part if the turntable wobbles, does not rotate properly, or if the guide is cracked or broken.

Replace your microwave's coupler holder if it's cracked, broken, or missing. This support piece secures the drive coupler to ensure proper operation.

Wire rack for microwave ovens. Installs inside the cavity to provide an elevated cooking surface. Replace if bent, rusted, or missing from your unit.