Parts for Whirlpool 5K45SS: 05 - Motor And Control Parts

Secures hinge, lever, or linkage to its bracket on your stand mixer. Replace this screw if stripped, missing, or damaged to restore proper alignment.

Replace your mixer's wavy spring washer to reduce vibration and noise. This washer maintains proper tension between shaft components for smoother operation.

Speed control lever cracked or broken? This mixer speed control lever restores speed adjustment. Simple 15-minute repair with basic tools.

Replacement spring for stand mixer control plate assembly. Maintains tension between speed control lever and plate. Needed when broken, missing, or worn.

Fix mixer stuck at one speed or won't turn off. This speed link connects to the speed control mechanism. Common DIY repair, takes 30-45 minutes.

Mixer won't turn off or stuck at one speed? This flat spring restores tension to the speed control mechanism. Common fix for speed link issues.

Replace a lost or damaged thermostat mounting screw to secure your mixer's temperature sensor in position for accurate heat control and consistent performance.

Mixer won't start or stopped working suddenly? A failed field assembly disrupts the motor's electromagnetic field. Moderate DIY repair restores power.

Fix a mixer that won't turn on or has burnt electrical smell. This motor field assembly controls variable speed. Replaces worn electrical components.

Stand mixer bearing supports and centers the rotating drive shaft for smooth, quiet operation. Replace when you hear grinding noises or vibration.

Fix a mixer that won't run, runs slowly, or smells burnt. This motor armature transfers power to attachments. Moderate DIY repair, about 1 hour.

Replacement screw fastener for stand mixers. Secures panels, trim, and brackets to the mixer body. Order when original screws are stripped, missing, or damaged.

If your stand mixer runs only on high speed or won't change speeds properly, a worn governor drive stud may be the cause. This small repair restores smooth speed control in about 30 minutes.

This flat washer provides a durable spacer and load-distribution surface for fasteners in laundry appliances, helping secure components and reduce wear. It's a simple replacement that restores proper fastening and alignment where a worn washer is causing issues. This is for 1 washer, the photo is an example of the washer.  

What it does:

• Distributes nut/bolt pressure to protect mounting surfaces and prevent loosening
• Maintains correct spacing and alignment of panels, brackets, or moving parts
• Helps reduce vibration-related noise and abrasion at fastener points
• Common symptom: loose or rattling panels or hardware where a washer has deteriorated

What's included:

• One flat washer

Install notes:

• Turn off power and unplug the appliance before accessing panels or hardware
• Remove the fastener, replace the old washer with the new one, and re-torque to the OEM-recommended specification
• Inspect surrounding hardware and replace any damaged screws or nuts for a secure repair

Mounting screw for washers and dryers. Secures internal components to the cabinet or frame. Replace if screw is stripped, missing, or broken.

Seals motor housing to prevent dust and moisture from damaging internal components. Replace if you notice oil leaking or residue buildup. Confirm fit with your mixer model.

Supports moving mechanisms in your stand mixer for smooth operation. Replace if you notice excessive noise, wobbling, or oil leaks. Verify fit with your model.

Locking nut for stand mixers. Secures the motor or attachment hub assembly. Replace if stripped, cross-threaded, or missing to restore secure attachment.

Small fitting that seats inside the brush holder assembly to align and secure the motor brush. Replace if cracked, missing, or worn to restore proper brush positioning.

Fix a mixer that won't start or runs weakly. Motor brushes wear from normal use and conduct electricity to power the motor. Basic DIY repair.

Mounting screw for washers. Secures internal components and panels. Replace if stripped, rusted, missing, or damaged during repair or maintenance work.

If your mixer makes excessive noise or vibrates during operation, a worn spring seat cap may be the cause. This part centers and secures springs for smooth, quiet performance.

Fix loose or unresponsive mixer buttons with this cap spring. Restores proper tension and reliable engagement. Simple DIY repair in minutes.

If your mixer motor runs weak or intermittently, this brush holder cap secures motor brushes for reliable contact. Simple DIY fix restores performance.

If your mixer runs intermittently or loses power, a cracked or missing brush holder cap may be letting the carbon brush slip. Simple threaded repair.

Fix a mixer that won't start or runs intermittently with this brush holder cap. Secures the carbon brush and spring in the motor assembly.

Fix a mixer stuck at one speed or losing power under load. This speed governor regulates motor performance. Moderate DIY repair with video guide.

Fix a mixer stuck on one speed or operating only at high speed. This speed control plate regulates mixer speed settings. Moderate DIY repair.

Power cord for stand mixers. Replaces damaged, frayed, or missing cords. Connects mixer base to electrical outlet. 230 volt specification.

If your stand mixer won't turn on or powers off intermittently, replace a frayed or damaged power cord. This cord restores safe electrical connection.

Replacement power cord for stand mixers. Connects your mixer to the wall outlet. Replace if frayed, heat-damaged, cracked, or loose for safe operation.

Replace your stand mixer's power cord if it's damaged, frayed, melted, or chewed. This electrical cord connects your mixer to the outlet for power.

Fix a mixer that won't start, runs constantly, or has only one speed. This phase control board regulates motor speed. Easy DIY repair with video guide.

Fix a mixer stuck at one speed or running sluggish with this phase control board. Regulates motor power across all speed settings. Video guide included.

Fix a mixer that won't run, runs slowly, or smells burnt. This motor armature transfers power to attachments. Moderate DIY repair, about 1 hour.

Fix a mixer that won't start, slows down, or makes grinding noises. This armature (motor rotor) restores reliable operation when worn or burned.

Protects your mixer shaft from wear and metal-on-metal contact. Replace when you notice rubbing noise or rough operation. Verify fit with your model.

Fastens panels and internal components in stand mixers. Replace if the original screw is missing, stripped, or damaged to restore secure assembly and fit.

Fix intermittent mixer operation or arcing sounds with this brush holder housing. Secures carbon brushes for steady motor contact and consistent speed.

Mixer won't run or just hums? Worn motor brushes in the holder cause power loss. This DIY repair restores full motor function on stand mixers.

Stand mixer Rotor Slicer, Shredder Attachment for KitchenAid Stand Mixer that includes four stainless steel slicing, shredding cones, and instruction booklet. The slicers include course, thick, think and fine shredder to shred vegetables, fruit and nuts. KitchenAid model number RVS-A

Two pack Lid Covers used with 4.5 and 5 Quart KitchenAid Tilt Head Stand Mixer. The covers are used for variety of situations for example, when you need to keep ingredients in the bowl cold for hours or want to save extra cookie dough. The Lid Covers are dishwasher safe on the top-rack and fit KitchenAid Stand Mixer models K45SS, KSM75, KSM95, KSM150PS, KSM152PS and KSM155GB.

Replace your cracked, worn, or missing 4.5-quart stainless steel mixing bowl. Fits tilt-head stand mixers with handle for easy pouring and removal.

Pouring shield attaches to the top of your stand mixer bowl to prevent ingredient splatter during mixing. Replace if cracked, broken, or missing.