Mtd Control Cable

The cable seen here is an authentic replacement that is sourced from the manufacturer. This control cable is used for lawn mowers. It will pivot to pull the belt idler pulley, which will fasten the belt and spin the mower's cutting blades. When the cable is not working properly, it could mean that the blades will not spin properly and not provide the mower with the cutting capability that it should have. The cable that comes with the mower tends to be durable, but this does not mean that it will not need to be replaced at some point. Many things could happen to the cable that would require a replacement. The spring might start to wear out, for example. The cable could become frayed or corroded, as well. Owners should always make sure they are wearing gloves when replacing this part. They will need a screwdriver and pliers to complete the repair. The cable is a genuine OEM replacement part that is sold individually. This cable will work with more than 130 models of mowers. Brands with compatible models include Craftsman, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, and MasterCut.

This is a durable rubber clutch cable that is used on lawn and garden tillers. It is used to connect the drive system to the clutch control arm in the equipment. It is an important component that controls the clutch to engage the machine. Over time, the clutch cable can break or become damaged and will need to be replaced. If a visual inspection shows that the clutch cable is broken, the first step is to remove the clutch handle. Take out the bolt on the cover plate for the arm. Take the old cable off of the handle and remove the cover plate. Loosen the screws so the old clutch cable can be removed. Remove the screws on the cover over the clutch and belt. Take off the old cable and attach the new one to the clutch. Tighten the screws and reassemble the parts and make adjustments before using the new cable.This clutch cable is a genuine OEM replacement component sourced directly from the manufacturer. It is sold as an individual part. This cable is compatible with tillers manufactured by MTD, Huskee, MasterCut, and Yard Machines.

This throttle cable is a genuine MTD part, sold individually. This throttle cable can be used as a replacement part for string trimmers. The purpose of a throttle cable for a string trimmer is to allow the speed of the engine to be easily regulated when pulling on and engaging the cable.The throttle cable of a string trimmer might have to be replaced at some point within the standard lifespan of a string trimmer in the event that the component is not functioning as it usually does. This could be the case if the throttle cable is damaged in the form of tearing, ripping, fraying, or erosion to the material. If the speed of the engine is not being regulated by the throttle cable when pulled or engaged, the throttle cable should be removed and replaced by this genuine OEM replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer. It is sold individually. This throttle cable is compatible with the following outdoor appliance brands: MTD, Troy-Bilt, Cub Cadet, and Craftsman.

This is a genuine OEM throttle cable that is designed for use with select gas string trimmers. The throttle cable connects to the carburetor and is used to stop the engine from running when the lever is shifted from throttle to choke. Over time, this cable is extended and retracted frequently and can become worn with use. It consists of the metal throttle cable and the plastic housing, and those can get broken or damaged as well, which will require the need for a full replacement. Without a functioning throttle cable, the engine may not run correctly, or the speed of the engine will not be able to be controlled. This replacement cable is ideal for compatible devices. This OEM throttle cable is manufactured to exact standards by MTD. It can be used with a variety of models of trimmers from MTD, Troy-Bilt, Yard Man, Cub Cadet, and Yard Machines. It is made of durable metal with a composite plastic housing. The trigger and screws are sold separately and will require an additional purchase if needed. Be sure to wear gloves when performing any equipment repairs.

This is a reverse cable that is used on many tillers. It's made of durable plastic and metal. The reverse cable is the component in a tool that allows the tiller to help disengage and engage the reverse drive function of the tiller. In some cases, the part will become frayed or broken and must be replaced. The cable also contains delicate connectors that can become damaged. If this occurs, the reverse cable itself will need a replacement. The cable can also become too stretched out and stop working correctly.If the reverse cable for a tiller is broken, stretched out, or otherwise damaged, a pair of pliers will be needed to replace the part. This is a simple repair that only takes a few minutes to handle. The frayed or damaged cable should be removed from the tiller so the new one can be installed in the same place. Before making the replacement, make sure the spark plug wire has been disconnected.This is an authentic OEM replacement component that is directly sourced from the manufacturer. The reverse cable is sold as an individual item. It is designed to be compatible with tillers manufactured by Yard-Man, Craftsman, Huskee, Cub Cadet, MTD, and Yard Machines.

The forward cable is used in yard and garden tillers. It is responsible for engaging the transmission which will cause the tiller to propel forward. It also works to rotate the tines in situations where the bail arm has been pulled toward the handle. If the forward cable starts to come loose or has lost proper tension, it may need to be tightening or replaced. This part will lose tension as time goes on, so making adjustments is part of its regular maintenance. However, a forward cable that is damaged or broken will need to be replaced. Work gloves should be worn when replacing the forward cable. Before replacement, the spark plug cap plug should be removed and the throttle lever needs to be pushed down. Next, remove the throttle lever, throttle cable clip, and then the forward cable. The new part can then be installed and the rest of the components replaced. This forward cable is created for use with Yard Man, Cub Cadet, MTD, Craftsman, Huskee, and Yard Machines tillers. It is an individual component that is genuine OEM and comes directly from the manufacturer. Various tools, including a screwdriver, pliers, and socket wrench may be needed for the replacement.

This lift cable is designed for use with many lawnmowers and snowblowers to ensure that the gears run smoothly while using the equipment. The lift cable is made of durable materials but has delicate connectors on each end which may eventually wear out. When the connectors or cables are damaged, the part will need to be replaced. This component is important since it helps control how fast the blades or other parts of the tool can operate. If the cable breaks, the tool may not start.If the lift cable has gone bad, is worn out, or is damaged, replacement is needed. There will be no need to use tools during the process, but work gloves can be helpful. The lift cable can be untwisted from the housing and removed from the tool. Take the new component and place it in the same location. Make sure to reassemble any additional parts before useThis is an authentic OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual component. The lift cable is made to fit lawnmowers and snowblowers manufactured by Craftsman, Toro, Cub Cadet, Troy-Bilt, MTD, Huskee, Montgomery Wards, and Yard-Man.

This throttle cable is a used on string trimmers. This part links the carburetor assembly to the throttle trigger. Each throttle cable is made with a connector on each end. Over time, the throttle cable can be damaged or kinked through use. If this occurs, the cable will need to be replaced.Replacing the throttle cable will require basic tools and a set of work gloves. The first step to replacing the throttle cable is removing the original component. The throttle housing will need to be taken apart on each side of the string trimmer. The replacement cable will pass through the carburetor mounting plate hole and the engine housing before reassembling the rest of the parts.This throttle cable is sold as an individual component. It is a genuine OEM replacement part that is sourced directly from the manufacturer. The throttle cable is made for use with string trimmers manufactured by Yard Machines, MTD, Craftsman, Murray, Yard-Man, Bolens, and Cub Cadet.

This part is a replacement speed control cable. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a defective, broken, or worn speed control cable in a variety of chipper and shredder models. The speed control cable allows the user to select the desired transmission speed. This part is subject to wear and tear and can snap or stretch over time. If this occurs, the equipment will not be able to be controlled properly and may be inoperable. It is always recommended that the appropriate safety precautions are adhered to when attempting to fix any power tools or machinery. For more accurate information on how and where to install this speed control cable, the appropriate owner's manual and included diagrams should be referenced.As an authentic replacement part, this speed control cable is suitable for use on several different models of chipper or shredders manufactured by MTD, Troy-Bilt, and Cub Cadet. This is a genuine part made of high-quality, durable materials and is sold individually.