Samsung Refrigerator RF268ABPNXAA Parts

We had a hard time finding a tutorial that showed how to replace the part of the handle that broke. After several attempts to fix on our own we gave up. A few weeks later a friend came to our house and we were discussing the fix for the handle and She helped me to fix the handle just buy trying a new way to remove the old broken part. It took us several tries but with her help I was able to fix the door handle and remove the broken part. I really wish your site had a tutorial for this... Read more

• Fridge too warm
• Doesn't shut off
• Noisy

The blower motor that circulates air through the refrigerator was broken. I had to remove all the shelving and drawers from the refrigerator. Then I had to remove the plastic light cover from the center of the fridge. Then I removed all visible screws to uncover the evaporator/radiator. I then unplugged the light bulb and motor wires. Luckily all wiring is keyed so that it can be plugged in again without error. I removed the motor by opening the motor housing. The housing has 1 screw and... Read more

Turn off the water to the ice maker. Unload the freezer and remove the freezer door so you have room to work. Remove the ice maker by removing 2 screws in the front then pull the unit toward the front and unplug the wiring connection. The pipe will now be exposed. Remove the flexible piece from the front of the pipe that directs the water flow to the ice cube tray. Remove the wire tie on the front of the pipe and peel off the insulation surrounding the pipe. The heater will now be exposed.... Read more

I took all the items out of the refrigerator. Removed the screws that hold the cover over the evaporator motor. Than for three hours used a hair drier to remove ice. The panel was frozen on if you pull on it it will break. Soaked up all the water removed the panel and took the fan blade off. That was difficult because it looks like a regular screw head however, you need to push in that which will cause it to release the blades and than push it onto the new motor. Than replace the panel put the... Read more

Using the website, I was able to locate the part and order it Read more

Took a bit to diagnose. First tried cleaning coils but the problem still persisted. Next took of the back panel and put the system into diag mode. (Press energy save button and fridge button for eight seconds system ding once a second and inverter board red LED will blink a code or be on solid if no issue. See back of the refrigerator for a sticker with what the number of blinks means. My unit one blinking 1 time. So I measured the resistance of the compressor between windings (8.9 ohms between... Read more

Ordered the two motors plus ordered the fan blades since I was afraid one might break during replacement. Changed out without breaking Freezer and both ice makers now working fine Read more

Replaced sensors and heater element. We'll see if that fixes the problem. It usually happens every 3 months. Read more

Took off the old ones, put on the new ones. Read more

First, I modified old butter knife by bending a 90° angle about 3/4" from the tip. I slid the bent in up under the bottom of the switch cover and worked it to one side. I then rotated the knife downward using the bent end to pry the cover off. The switch is held by plastic arms on each side. The bottom right arm has a locating pin that fits into the switch. Unplugged the switch and re-installed. Read more

• Noisy

I bought new parts, motor and fan. Replace the old one. Took me no more than 15 minutes to fix it. Read more

Samsung refrrigerator. it started when the setting was on cubes but was putting out crushed ice. then months later the water refill was running down into the ice bucket causing a massive block of ice in the bucket. look closely at the first two or three cubes in the ice tray after they unload. mine were not dumping and staying in the tray. when the water refill kicked on it would overfill the tray (because of the leftover cubes remaining in the tray) and would run down into the ice bucket... Read more

The Samsung french door freezer has a handle that has plastic pivot plates that help "push" the door open during its first inch or so of travel. One morning, the handle pulled off taking portions of both pivot plates with it! The parts from AppliancePros arrived very quickly, and the repair required re-positioning the mounting holes, even thought the replacement parts looked identical to what was left of the pivot plates. Okay, that‘s not AppliancePros fault in any way whatsoever; this happens... Read more

I removed the door and the hinge assembly from the right side; it turns out the grommet had never been installed and this is what was causing the door to grind down the metal hinge. It was remarkably easy to replace and my door is working perfectly! Read more

In order it SHOULD be done: Pried off two white caps covering the screws that attach the flap to the left door, then removed screws. Lifted flap up to remove from door and disconnected cable. Used a thin blade to pry out the inner cover of the flap, then carefully pried out the insulation piece inside. Loosened the screw holding the center cap from the inside and removed cap. Worked the cable out of the hinge piece so it could be removed and cable pulled through case. Pried upper and lower caps... Read more

Samsung does not make it easy to replace the casters. The shafts holding the casters are crimped at the ends and had to be cut off with little room for any tools. I had to jack up the fridge and I used a hacksaw blade with a handle to cut through the wheel shafts. I didn't want to use a reciprocating saw. I couldn't find a way to crimp the new shafts so I drilled small holes at the ends and used cotter pins to retain the shafts in place.The rear caster had no room to slide the new one in... Read more