Samsung Refrigerator RF268ABPNXAA Parts

• Frost buildup
• Doesn't shut off

Ordered parts, defrosted refrigerator, and replaced with new items. This problem has been going on quite some time, while Samsung refused to acknowledge the defective unit, claiming it was owner fault. The defrosting had to be completed every 3-4 months and managed in time to require defrosting every few days. Originally a repairman came and although he defrosted it the first time, he informed us, this is quite common and the unit is defective by design; which is why we continued to defrost on... Read more

I replaced the temperature sensor, the thermo fuse, and the heating element that thaws the evaporator on a cycle to keep the evaporator from freezing up. The most time consuming part of the repair was waiting for the fridge to thaw out so that I could remove the cover. I disconnected the fridge the night before and placed a fan on low with the doors open so that it was thawed out when I awoke. It was easy to remove the evaporator cover once I removed all of the shelves. I took pics as i was... Read more

The Samsung french door freezer has a handle that has plastic pivot plates that help "push" the door open during its first inch or so of travel. One morning, the handle pulled off taking portions of both pivot plates with it! The parts from AppliancePros arrived very quickly, and the repair required re-positioning the mounting holes, even thought the replacement parts looked identical to what was left of the pivot plates. Okay, that‘s not AppliancePros fault in any way whatsoever; this happens... Read more

I replaced the control board and the microswitch. Read more

Samsung does not make it easy to replace the casters. The shafts holding the casters are crimped at the ends and had to be cut off with little room for any tools. I had to jack up the fridge and I used a hacksaw blade with a handle to cut through the wheel shafts. I didn't want to use a reciprocating saw. I couldn't find a way to crimp the new shafts so I drilled small holes at the ends and used cotter pins to retain the shafts in place.The rear caster had no room to slide the new one in... Read more

Order a new fixer Read more

I looked at the blow up drawing to figure out what parts I might need. I then watched a you tube video to see how to take the handle off. I kind of figured out on my own how to remove the ruined cap handle. It took me a few minutes to figure it out and more time to remove both the handle and the broken part. Turns out I did not need the spring nor the shaft cap handle. Very proud of myself. Saved a huge amount of money. Only problem was that I could only put in one screw as the previous... Read more

Ordered tank and heater, installed, so far so good. Thanks for the speedy order Roman Read more

Repair required removing all of the interior drawers & shelves and the interior back panel. There you will find the defrost heater. Behind the defrost heater is a metal plate as well as one on the back of the front interior cover. Both were corroded and in need of replacement. I ordered Samsung part #’s AP5577767, plate drain & AP5587916, evaporator plate and replaced both. Read more

Replaced original parts- Only skill needed was finding plastic push tabs. No tools required. Most of time was used for removing food from refrigerator before looking for tabs. Read more

Ordered tank and heater, installed, so far so good. Thanks for the speedy order Roman Read more

Removed the bottom shelf by releasing the 2 clips near the water filter, then lifted the front of the shelf and slid it out. Removed 2 screws from the broken Vegetable Rail and replaced it with the new one. Slid the shelf back into place and locked it down into the clips. Done. Took longer to remove everything from the shelf than it did to fix it. Less than 5 minute repair. Read more

In order it SHOULD be done: Pried off two white caps covering the screws that attach the flap to the left door, then removed screws. Lifted flap up to remove from door and disconnected cable. Used a thin blade to pry out the inner cover of the flap, then carefully pried out the insulation piece inside. Loosened the screw holding the center cap from the inside and removed cap. Worked the cable out of the hinge piece so it could be removed and cable pulled through case. Pried upper and lower caps... Read more

I removed the broken rail saving the 2 Phillips head screws for installation of new drawer rail. Removal of the shelf above the drawers was required and was accomplished by pushing a button on the front of the shelf support. The installation was a snap and took about 10 minutes after removal of food items. The part was the correct one as verified by the model number on the inside of the refrigerator door. Thanks AppliancePartsPros.com! Read more

Replaced sensors and heater element. We'll see if that fixes the problem. It usually happens every 3 months. Read more

The start button had been tricky to use. You had to push it in just a certain way to get the dryer to start. Eventually it was non-responsive. All other controls worked and there was no error code displayed. The repair was to replace the whole control board which cost around $100. Heavy sigh.. Be sure to keep track of all your screws. BTW it was not the thermal fuse. All the online videos say this is the first thing to look for when the dryer will not start. Be sure to check with the person... Read more