Samsung Refrigerator RF26XAZBP Parts

• Not dispensing water

Purchased both the ice maker assembly and the valve assembly to replace the parts as needed. replaced the ice maker assembly first, and this fixed my problem. Took about 10 minutes, mainly because I didn't watch the YouTube video first. Had I watched that, it would have probably taken even less time. One Philips head screw driver is all you need. Read more

• Noisy

I bought new parts, motor and fan. Replace the old one. Took me no more than 15 minutes to fix it. Read more

I removed the door and the hinge assembly from the right side; it turns out the grommet had never been installed and this is what was causing the door to grind down the metal hinge. It was remarkably easy to replace and my door is working perfectly! Read more

Samsung does not make it easy to replace the casters. The shafts holding the casters are crimped at the ends and had to be cut off with little room for any tools. I had to jack up the fridge and I used a hacksaw blade with a handle to cut through the wheel shafts. I didn't want to use a reciprocating saw. I couldn't find a way to crimp the new shafts so I drilled small holes at the ends and used cotter pins to retain the shafts in place.The rear caster had no room to slide the new one in... Read more

Used the video with the parts and replaced the wheels. The only thing we did wrong was using the front wheel axle instead of the back wheel axle on the back wheels. I will just order two more front wheel axles which are longer than the back axle. Thank you for the video, it made this repair easier. Read more

Order a new fixer Read more

Samsung does not make it easy to replace the casters. The shafts holding the casters are crimped at the ends and had to be cut off with little room for any tools. I had to jack up the fridge and I used a hacksaw blade with a handle to cut through the wheel shafts. I didn't want to use a reciprocating saw. I couldn't find a way to crimp the new shafts so I drilled small holes at the ends and used cotter pins to retain the shafts in place.The rear caster had no room to slide the new one in... Read more

Ordered tank and heater, installed, so far so good. Thanks for the speedy order Roman Read more

In order it SHOULD be done: Pried off two white caps covering the screws that attach the flap to the left door, then removed screws. Lifted flap up to remove from door and disconnected cable. Used a thin blade to pry out the inner cover of the flap, then carefully pried out the insulation piece inside. Loosened the screw holding the center cap from the inside and removed cap. Worked the cable out of the hinge piece so it could be removed and cable pulled through case. Pried upper and lower caps... Read more

Repair required removing all of the interior drawers & shelves and the interior back panel. There you will find the defrost heater. Behind the defrost heater is a metal plate as well as one on the back of the front interior cover. Both were corroded and in need of replacement. I ordered Samsung part #’s AP5577767, plate drain & AP5587916, evaporator plate and replaced both. Read more

In order it SHOULD be done: Pried off two white caps covering the screws that attach the flap to the left door, then removed screws. Lifted flap up to remove from door and disconnected cable. Used a thin blade to pry out the inner cover of the flap, then carefully pried out the insulation piece inside. Loosened the screw holding the center cap from the inside and removed cap. Worked the cable out of the hinge piece so it could be removed and cable pulled through case. Pried upper and lower caps... Read more

The start button had been tricky to use. You had to push it in just a certain way to get the dryer to start. Eventually it was non-responsive. All other controls worked and there was no error code displayed. The repair was to replace the whole control board which cost around $100. Heavy sigh.. Be sure to keep track of all your screws. BTW it was not the thermal fuse. All the online videos say this is the first thing to look for when the dryer will not start. Be sure to check with the person... Read more

Completely defrosted the refrigerator ,took 2days then replaced temp sensor and heater the repair took about 45 minutes so far everything is working fine Read more

New flap housing with a new spring and the new replaceable guide. I didn't know the screw to hold the guide to the housing and forgot to add the spring bushing to my cart during checkout. It was pretty simple, only reason I didn't give it an easy rating is because having to pop off the hinge caps was making me think I was going to snap some of the cheap plastic, kinda have to be careful Read more

Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more

I removed the door and the hinge assembly from the right side; it turns out the grommet had never been installed and this is what was causing the door to grind down the metal hinge. It was remarkably easy to replace and my door is working perfectly! Read more