Poulan Chainsaw Parts

This genuine Husqvarna bolt and washer replacement part is specifically engineered to hold and secure the lawnmower blade in place. The bolt is threaded while the washer has a curved or rounded headed. A washer is needed for even load distribution of the threaded bolt. Fastening the bolt without the fastener may cause stress to the material it's driven into. One of the warning signs that the bolt and washer are broken is if the lawnmower blade doesn't rotate properly. Instead of moving in one circular motion, it turns erratically and goes up and down. In some cases, it will make a loud grinding noise during cutting. The lawnmower blade may even fly out from its normal position. Replacing the worn-down bolt and washer is fast and straightforward. First, shut down the engine and let it cool. Then, take out the spark plug and turn the mower on its side. Use a socket to remove the old bolt and washer. Then, grab the replacement and insert it through the blade's hole. Tighten it using the socket. This original Husqvarna bolt and washer is only suitable for lawnmowers made by Husqvarna, Craftsman, and Weed Eater. It is also compatible with some Dixon and Poulan lawnmowers. This bolt and washer replacement is sold individually.

This genuine Husqvarna fuel cap provides cover and protection to the hole into which engine oil is dispensed on certain lawn mowers, lawn tractors, and snowblowers. This fuel cap should remain closed when the appliance at hand is not in use in order to prevent leakage.If the engine of a small engine appliance is suffering from frequent leakages, there could be damage in the fuel cap that is causing the leaks. A fuel cap could also become misplaced. If the cap is broken or lost, it must be replaced immediately before using the small engine appliance again. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This fuel cap is compatible with the following brands: Husqvarna, Poulan, Ariens, and Craftsman. This part is sold individually.

The chainsaw thumb wheel assembly, sometimes called a wheel gear assembly or a chainsaw knob, is an important part of the chain adjustment system. Turning the wheel will allow users to tighten or loosen the chain on the saw. The thumb wheel assembly, made of plastic and metal, could become worn down or broken over time, which will require a replacement. If this part of the chainsaw is not working properly, it will not be possible to make adjustments to the chain's tension. Owners would not be able to remove their old chain or add a new one. The new thumb wheel assembly is easy to install and will get the chainsaw back in working order. The authentic OEM chainsaw thumb wheel assembly is sold individually. It is compatible with models from Husqvarna, Poulan, Poulan Pro, and Craftsman. Buyers should consult their manuals to ensure they are getting the correct part for their chainsaw's make and model.

The recoil spring is a vital part of the starter mechanism in chainsaws. It will apply tension on the pulley, which allows it to retract the rope. Without a working spring, it will be difficult or even impossible to start the chainsaw. While the metal springs are durable, they could start to wear out over time and will no longer be effective. In addition, the springs could suffer damage or could become corroded. They could also be lost when making other repairs to the chainsaw. If there is any issue with the spring, it will require a replacement. This authentic OEM replacement recoil spring is sold individually. The chainsaw recoil spring is compatible with several brands including Poulan, Poulan Pro, Husqvarna, Jonsered, Craftsman.

This wire harness assembly is an authentic replacement for chainsaws. It is supplied from the manufacturer. The wire harness assembly connects to the ignition module. It is made of two wires. One of the wires carries the power from the coil to the switch, while the other wire attaches to the engine ground on one side and has a switch contact on the other side. The wires have a rubber insulated coating that helps to protect them from high heat. These wires can suffer damage in many ways. They could become frayed or cut, they could have been subject to extremely high temperatures, and more. When they are damaged, it can cause a continuity loss in the circuit which can shut off the saw. Owners should look for broken or frayed wires. They can also use a multimeter to check the wires for continuity. If there are issues, the wires should be replaced right away. The chainsaw wire harness assembly is a genuine OEM replacement part for use with chainsaws. The assembly is sold individually. It will work with select chainsaws from Craftsman, Husqvarna, Poulan, and Poulan Pro.

This chain brake is made to connect above the drum of a chainsaw. It has a metal band that goes around the drum and a handguard that also connects to the brake. When the guard is pressed forward, the brake band tightens on the clutch drum, making the chain stop immediately. The brake is pre-assembled and consists of both metal and plastic parts. The spring, brake band, and linkage are all metal, and the housing is plastic. A common chain brake problem is the brake band becoming worn out or damaged. This causes the brake to no longer stop the chain fast enough or at all. This can be incredibly dangerous, so it’s important to check the brake regularly. Installing a new chain brake is straightforward with this genuine OEM part sourced directly from the manufacturer. Just remove the clutch cover assembly, take off the old chain brake, and screw in the new kit. Be sure to wear gloves and let the engine cool completely before making repairs. Compatible with Craftsman, Poulan, and Poulan Pro chainsaws. Sold individually.

This is a complete set of gaskets designed as a set to make the most of chainsaw maintenance and repair. This OEM gasket kit contains seven unique gaskets that should be replaced whenever a chainsaw's motor is serviced or repaired. Gaskets are designed to ensure that fuel remains where it is intended within the engine and parts and does not leak or seep into other areas. The pressure is maintained in the machine through the use of effective gaskets and seals. This is a complete kit and comes with every gasket needed for chainsaws made by Craftsman, Husqvarna, Poulan, and McCulloch, among others. It does not come with any associated parts necessary for full chainsaw maintenance and will require disassembly of several systems to install the new gaskets.

This is a brake pad. The brake pads attach to clips and serve to stop the mower. The pads push against the rotors and cause friction, allowing the mower the stop movement. Worn-down brake pads can be hazardous to the rider and the mower. There are several signs of worn-down pads. There may be a squeaking or scraping sound coming from the wheel area. If the problem persists, a noticeable grinding sound can even be felt when the mower is driven.Replace the pads by removing the wheels. The pads are attached to calipers that fasten to the rotors. These are removed with a socket wrench. After removing the calipers, there are clips that fasten the pad in place. Push these clips and remove the old pad. Repeat these steps in reverse to install the new pads.This product is a genuine OEM part and is sourced directly from the manufacturer. These Husqvarna brake pads are sold individually as separate components from the rest of the machine. This product is only compatible with Husqvarna machines.

This genuine OEM replacement washer is a specially hardened washer to provide more support for a wide range of different lawn appliances. Washers are usually used in conjunction with a nut and a bolt and act as a barrier between those two parts. Washers help to redistribute pressure to prevent the bolt from giving out over time, as well as to provide a stronger grip. Washers can begin to corrode over time, and when this happens, the washer can fuse together with the bolt or nut. This would make the connection difficult to disengage in the case of a bigger repair. It is good practice, then, to replace washers anytime the nut or bolt is also replaced. This way, all parts age at the same rate and will not have to be individually changed out. Use a wrench to unthread the nut and change out a washer. This part is a top of the line replacement washer for a Husqvarna, Weed Eater, Ryobi, Jonsered, or Poulan engine. It comes sourced from the original manufacturer and does not include any other hardware.

This linkage brake is a genuine Husqvarna part, sold individually. This linkage brake can be used as a replacement part in a lawnmower. The purpose of the linkage brake in a lawnmower is to affix in the space between the idler arm and the mower arm brake such that the brake arm can facilitate the ceasing of rotation of the blades.The linkage brake could suffer damage from general wear and tear over long-term use or as the result of a collision with a hard object such as a rock or a curb. If this occurs, the linkage brake should be removed and replaced by this genuine OEM replacement part in accordance with the proper set of instructions sourced from a relevant appliance manual. This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This linkage brake is compatible with the following outdoor appliance brands: Husqvarna and Craftsman.

This replacement starter spring is a genuine OEM model from Husqvarna. The starter spring, also sometimes called the recoil spring or recoil starter spring, is part of the entire starter assembly. It attaches to the fan and flywheel housing and is responsible for helping to retract the starter rope when it is pulled to engage the engine. Over time, the spring can wear out or become twisted. This can cause the starter rope to no longer retract or it can even seize up the entire starter assembly. Replacement of the spring is the only option and this OEM part can provide an exact fit for select engines. This part is designed for use with blowers, edgers, trimmers, and pruners that feature Husqvarna engines and that are manufactured by brands like Weed Eater, Poulan, and Husqvarna themselves. The starter spring is made of durable metal and is sold individually. Always disengage the spark plug and allow the engine to cool completely before beginning and repair projects, and protect the hands by wearing gloves.

This is a replacement chainsaw bar adjustment pin that is a part of the clutch cover assembly. The pin connects to the adjustment screw and will fit into the hole on the bar. By turning the screw, it will turn the adjustment pin, which will loosen or tighten the chain on the bar. The bar adjustment pin is hearty, but it can become damaged through corrosion, wear and tear, and more. In addition, it could also be lost. Because the pin is essential, it is important to replace the pain when it shows signs of distress or when it is lost. When using the adjustment pin or adding a replacement, the owner mustn't overtighten the pin. This can cause damage to the pin, which would necessitate another replacement. This is a genuine OEM replacement pin that is sold individually for use on chainsaws. The pin is compatible with several brands including Craftsman, Husqvarna, Poulan, and Poulan Pro.

This is a genuine air filter replacement designed for use in select lawn and garden equipment engines. The air filter is responsible for catching debris and dirt that may be in the air as it comes into the engine. This prevents the engine from being damaged by debris or buildup. Over time, the air filter will become clogged and should be replaced as a part of routine maintenance. It is helpful to keep an extra air filter on hand in case of an emergency replacement need. This genuine OEM air filter is manufactured by Husqvarna and meets exact standards for compatible models. It can be used in select models of chainsaws from the brand, as well as some from Jonsered. This air filter is sold as an individual unit and does not include any additional parts or accessories. A screwdriver will be required for replacement. To replace the filter, allow the engine to cool. Then, remove the screws from the cover of the filter and take out the old filter. Put the new filter in place and replace the cover. Then, reattach the screws and the job is done. Be sure to wear gloves when performing engine repairs.