Poulan Parts

This is a replacement carburetor for Husqvarna string trimmers and is also used on some Craftsman models. It consists of an aluminum body with a bright blue choke and cherry red primer bulb. Engines rely on a mixture of fuel and air for proper operation. In a small engine, the fuel and air mix inside the carburetor. This is achieved with a series of small channels, which release a fine mist of fuel into a vortex of air. When one of these channels gets clogged, it can negatively impact engine performance. Carburetors can often be cleaned with a commercial carburetor cleaning spray, but this is sometimes not sufficient to clean a badly clogged carburetor. In this case, other measures such as hypersonic cleaners can often be effective, but they’re not always worth the cost. The alternative is replacing the entire carburetor, which can be done using this kit. This is an OEM part sourced directly from the manufacturer, and it is sold individually. A heat shield is also included with the kit.

This is a grass catcher frame that secures the grass catcher bag to the body of the mower. Mowers are twisted, lifted, and banged constantly, so a frame may become warped beyond use. If so, this OEM manufactured part is the solution. The replacement is an easy fix and should require less than 15 minutes and doesn’t require any tools. Simply remove the grass bag from the old frame, noting how the bag fit. Slide the new frame inside the bag. It should fit snugly with no undue tautness or slack. To make certain the frame was properly introduced into the bag, attach the frame to the mower. If the frame fits securely against the cowling of the mower, then the bag and frame have been fitted properly together. This grass catcher frame was designed specifically for Husqvarna and Poulan lawnmowers, though there are also a number of Craftsmen mowers on which this frame can be installed. This OEM part is sold individually. Bag sold separately.

Lawn tractor won't start when you turn the key? This starter solenoid links your battery to the starter motor. Common DIY fix for no-crank issues.

Mixes air and fuel for your chainsaw engine. Replace if cracked, damaged, or leaking. Installs on engine, may include primer and fuel lines.

Filters air to remove dust and debris that could damage your chainsaw engine. Replace regularly as part of normal maintenance. Confirm fit with your model.

Replacement fuel line kit for chainsaws. Includes tubes that feed fuel to carburetor and return unused fuel to tank. Replace if cracked, brittle, or leaking.

Replacement blade cap assembly for riding mower tractors. Secures mower blade to spindle shaft. Replace if cracked, broken, or missing for safe operation.

Greaseable blade spindle assembly for riding mower decks. Mounts to the underside of the mower deck and holds the cutting blade. Replace if cracked, worn, or damaged.

Ignition module for gas leaf blowers and trimmers. Works with flywheel to create spark timing. Replace if damaged by heat exposure or engine won't spark.

Clutch washer kit includes washer and clip. Protects engine by evenly distributing pressure at connection points. Replace if worn, corroded, or missing.

Blocks dirt and debris from entering your trimmer engine. Replace when clogged or worn to restore proper airflow and prevent rough running or starting issues.

This is a genuine OEM replacement drive V-belt for a riding lawn mower. The drive V-belt attaches to the drive pulley and transfers rotational motion from the transmission to the mower blade. This causes the blade to then spin and cut grass. By using a belt to transfer motion, the engine does not have to work as hard to spin multiple parts, meaning that it runs more efficiently. Drive V-belts are made of a rubber composite material that will begin to fray and stretch over time. Due to continuous motion, these belts absorb a lot of wear and tear, and if left for too long, they can eventually snap and leave the mower blade non-functional. Therefore, it is wise to check the condition of a V-belt during regular maintenance. As soon as it appears to be wearing away, replace it with a new part using a nut driver and screwdriver. When detaching the lower deck, be sure not to lose the bolt clips, as they are required for reassembly. As a high-quality replacement part, this drive V-belt is directly sourced from its original manufacturer. It is compatible with riding lawn mowers made by Husqvarna, Poulan, Craftsman, and Jonsered. This part ships individually.

A V-belt is responsible for transmitting energy. It is made from a thick and sturdy rubber material. It features grooves for improved traction and measures ½ x 95-1/2. A worn-down v-belt can lead to inefficient energy loss, and therefore poor performance. Installing this v-belt requires pliers and a wrench. First, the spark plug wire needs to be removed. Then, position the mower deck to the lowest possible level. Move the machine's blade engagement level to OFF. Remove the belt found from the engine pulley. Don't forget to take out the bow-tie pins and blade engagement cable as well. Remove the bolt from the pulley cover and loosen the nuts found at the idler pulley. Put the new belt and then tighten the nuts on the idler pulleys. The deck can now be re-assembled to its original position. This Husqvarna 532144959 V-Belt OEM Replacement can help keep a lawnmower in top condition. This genuine Husqvarna made V-belt is specifically for driving the blades on a lawnmower. It is compatible with Ariens, Craftsman, Poulan Pro, Dixon, and Husqvarna mowers. This V-belt is sold individually.

Mower won't start or starter doesn't engage? This ignition switch activates your riding mower's electrical system. Simple DIY repair in under 30 minutes.

If your chainsaw rope won't retract after pulling, the starter spring likely needs replacement. This spring creates the recoil to start the engine.

Replacement fuel tank for front-engine lawn tractors and riding mowers. Installs to store fuel. Replace if cracked, damaged, or leaking.