Poulan Parts

Starter won't pull freely or rope doesn't retract? This recoil starter spring retracts the pull cord and activates your engine. Simple DIY repair in minutes.

This genuine Husqvarna fuel cap provides cover and protection to the hole into which engine oil is dispensed on certain lawn mowers, lawn tractors, and snowblowers. This fuel cap should remain closed when the appliance at hand is not in use in order to prevent leakage.If the engine of a small engine appliance is suffering from frequent leakages, there could be damage in the fuel cap that is causing the leaks. A fuel cap could also become misplaced. If the cap is broken or lost, it must be replaced immediately before using the small engine appliance again. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This fuel cap is compatible with the following brands: Husqvarna, Poulan, Ariens, and Craftsman. This part is sold individually.

Secures the mower blade to the motor shaft. Replace if adapter is worn, stripped, cracked, or no longer holds the blade firmly in place during use.

Steering shaft connects the steering wheel to the gearbox on riding mowers and lawn tractors. Replace if bent, cracked, or worn for proper steering control.

Genuine engine cylinder for gas line trimmers and outdoor power equipment. Houses the spark plug and piston to create the combustion chamber. Replace if cracked or worn.

Recoil spring for chainsaw starter mechanism. Applies tension to pulley for rope retraction. Replace if worn, rusted, broken, or damaged to restore operation.

The carburetor kit has a metal body that is designed to withstand high temperatures, a rubber primer bulb, and a plastic throttle lever. The carburetor is an integral part of engines in lawn and garden equipment. This is where the air and fuel will be mixed before being sent into the engine. The air comes in through the intake tube, and it flows into a smaller tube, where the fuel is injected through small holes in the carburetor body. Then, the two are mixed and released into the engine through a butterfly valve, which controls the amount of fuel going to the engine for optimal performance. The carburetor can become clogged over time or even be broken or damaged. If the engine is not running properly, the carburetor may need to be replaced. This is a simple replacement that only requires a screwdriver. Make sure to always disconnect the spark plug and wear gloves when performing engine repairs. This kit can be used with several models of lawn and garden equipment, including brands like Weed Eater, Paramount, Poulan, Jonsered, and Husqvarna.

This is a genuine OEM replacement drive V-belt for a riding lawn mower. The drive V-belt attaches to the drive pulley and transfers rotational motion from the transmission to the mower blade. This causes the blade to then spin and cut grass. By using a belt to transfer motion, the engine does not have to work as hard to spin multiple parts, meaning that it runs more efficiently. Drive V-belts are made of a rubber composite material that will begin to fray and stretch over time. Due to continuous motion, these belts absorb a lot of wear and tear, and if left for too long, they can eventually snap and leave the mower blade non-functional. Therefore, it is wise to check the condition of a V-belt during regular maintenance. As soon as it appears to be wearing away, replace it with a new part using a nut driver and screwdriver. When detaching the lower deck, be sure not to lose the bolt clips, as they are required for reassembly. As a high-quality replacement part, this drive V-belt is directly sourced from its original manufacturer. It is compatible with riding lawn mowers made by Husqvarna, Poulan, Craftsman, and Jonsered. This part ships individually.

Replacement drive control cable for walk behind lawn mowers. Installs to connect drive mechanism. Replace if snapped, worn, frayed, or damaged.

Mandrel spacer washer for riding mowers and lawn tractors. Installs between drive pulleys to maintain proper alignment and spacing. Replace if worn or missing.

Hardened washer for lawn tractors and riding mowers. Installs with bolts to redistribute pressure and prevent loosening. Replace if worn or missing.

Secures the mower blade to the spindle on riding mowers and tractors. Replace if bolt is stripped, washer is damaged, or hardware is missing.

Idler pulley for riding mowers and tractors. Maintains proper belt tension for drive system. Replace if pulley is cracked, worn, or spinning rough.

Husqvarna makes this replacement wheel assembly, which measures 8 inches in diameter and has a width of 1.75 inches. The purpose of this wheel assembly is to keep a lawnmower mobile to ensure a lawn or yard has a clean and well-maintained appearance. If the lawnmower's self-propel function is not working, the drive gear on the wheel may be stripped and need to be replaced. It is a relatively simple task that will only require a wrench. First, the lock nut will need to be removed before the old wheel is taken off. Install the new one and secure the lock nut. Aside from Husqvarna, this part is also compatible with other lawnmower brands, including AYP, Craftsman, Dixon, Jonsered, McCulloch, Poulan, Poulan Pro, Redmax, and Weed Eater. It is an OEM part sourced directly from the manufacturer and is sold individually.

This pinion gear is an essential part of the steering assembly as it translates the rotation of the steering shaft into vertical motion. The pinion gear travels along the drivetrain, which pushes the wheels either forward or backward, causing the mower to turn. Without a functioning pinion gear, the mower will no longer steer. A pinion gear's teeth can slowly wear away through repeated use, causing it to begin slipping. When this happens, the operator will no longer be able to turn their mower as effectively or possibly not at all. This can be dangerous for the operator and they should stop mowing immediately. With most push lawn mowers, the pinion gear is located inside the wheel well. To replace it, simply remove the wheel and mounting washer, pop off the retaining ring, and remove the pinion. Reassemble and test the forward motion of the wheel. This genuine replacement OEM part is compatible with a number of lawn mowers from Poulan, Jonsered, Husqvarna, and Weed Eater. It comes sourced from the original manufacturer and does not include any additional hardware.