Range / Cooktop / Oven Fuse Or Sensor

This probe thermistor monitors interior temperature and sends readings to the control board so your appliance can maintain the correct cooling cycle. It replaces a failed or inaccurate sensor to help restore proper temperature regulation. What it does:

• Senses air or evaporator temperature and reports it to the control module
• Commonly related to warm/freezing issues, incorrect temperature readings, or erratic cycling
• Used by the control system to trigger fans, defrost, and compressor operation as needed
• Works as a direct replacement for the listed OEM temperature probe

• Disconnect power before replacing to avoid shock or damage
• Handle the sensor tip and wiring gently to avoid damage to the element or insulation
• Route and secure the wiring so it does not contact moving parts or hot surfaces

This 15 amp, 250 volt replacement fuse protects your appliance's electrical circuits by interrupting power when a fault or overload occurs. It restores safe operation once the underlying issue is fixed and the fuse is replaced. What it does:

• Acts as an overcurrent protection device for circuits rated up to 15 A and 250 V
• Prevents damage to wiring and components by opening the circuit during an overload or short
• Common symptom: appliance has no power or specific functions stop working after a sudden failure
• Replacing a blown fuse can resolve intermittent power loss or complete power failure tied to a single blown element

• Disconnect power to the appliance before inspecting or replacing the fuse
• Replace only with a fuse of the same amperage and voltage rating to maintain safety and proper protection
• Use insulated tools and avoid touching live terminals; internal access may require disassembly, follow OEM service instructions
• If fuses blow repeatedly, stop using the appliance.

This thermoprotector switch is a safety device that monitors oven temperature and cuts power to the heating element if the oven exceeds safe operating temperatures. It helps prevent overheating and potential damage to the oven's components. Replace this switch if your oven shuts off unexpectedly, fails to heat properly, or if you suspect the thermal safety cutoff is no longer functioning correctly.

This humidity sensor detects moisture levels inside the microwave cavity during cooking. It allows the microwave to automatically adjust cooking time and power when using sensor-cook or auto-reheat functions. Replace this sensor if your microwave consistently overcooks or undercooks food on sensor settings, or if you receive error codes related to the humidity sensor.

This is a thermal fuse used in a range vent hood to protect the electrical circuit from overheating. It acts as a safety device that interrupts power if temperatures exceed safe limits. Replace this fuse if the vent hood suddenly stops working or loses power without any other visible electrical issues.

This is a humidity sensor that detects steam levels inside the microwave cavity during cooking. It communicates moisture readings to the control board, allowing auto-cook and sensor-reheat functions to determine when food is done. Replace this sensor if your microwave's auto-cook cycles run too long or too short, or if sensor cooking modes no longer work properly.

This high limit safety thermostat monitors the oven temperature and cuts power to the heating elements if the temperature exceeds a safe threshold. It helps prevent overheating and potential fire hazards. Replace this part if the oven shuts off unexpectedly, fails to heat at all, or if the oven temperature runs excessively high.

Oven won't heat or suddenly stops working? This thermal fuse cuts power when temperatures exceed safe limits. Moderate DIY repair in 30-45 minutes.

Microwave won't start or stops mid-cycle? A blown fuse is often the culprit. This 5 amp fuse protects your microwave's electrical system. Quick DIY fix.

Oven overheating or won't heat properly? This safety thermostat monitors backguard temperature to prevent overheating. Simple DIY fix restores safe operation.

Range not heating properly or showing temperature errors? This temperature sensor probe monitors oven heat levels. Moderately easy repair in 30-45 minutes.

This is a thermal cut-out safety device that shuts off the microwave when internal temperatures exceed safe operating limits. It functions as a protective thermostat to prevent overheating and potential damage to the appliance. Replace this part if the microwave shuts off unexpectedly during use, fails to power on, or if the unit is overheating.

 The Thermostat is an OEM part for Whirlpool microwaves. It is a temperature-sensitive component that monitors heat levels inside the oven cavity during operation.

Causes may include damage from exposure to moisture or debris over time that disrupts accurate readings.

Symptoms of a faulty thermostat include:

• Incomplete or inconsistent heating with uneven hot/cold spots
• Food not reaching expected doneness after preset times
• Overheating errors or cycle interruptions

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.