Range / Cooktop / Oven Gasket & Seal

The Oven Door Gasket is an OEM replacement part for GE ranges and wall ovens. It provides a secure seal around the oven door to contain heat within the cooking cavity. The gasket is essential for efficient operation as it helps maintain optimal cooking temperatures.

Causes of a bad door gasket can include heat damage over time, warping from repeated door openings and closings, or accidental tears and ruptures. 

Symptoms of a bad oven door gasket include: 

• Excessive heat loss around the door area 
• Inconsistent or inefficient cooking performance
• The door not sealing properly, allowing heat to escape
• Rust or corrosion on interior door parts

This OEM GE part is compatible with GE, Hotpoint, Monogram, and certain Kenmore wall oven models.

This surface burner gasket seals the burner assembly to the cooktop. Replacing a worn gasket restores a tight seal to help support reliable ignition, a stable flame, and keeps spills and moisture from entering the burner well. What it does:

• Seals between the surface burner assembly and cooktop
• Helps maintain proper airflow for consistent ignition and flame
• Helps prevent liquids, crumbs, and grease from seeping below the burner
• Common symptoms of failure: distorted or hardened gasket, visible cracks, uneven/weak flame, or persistent clicking during ignition

• 1 gasket

• Disconnect power and shut off gas supply; allow the appliance to cool completely
• Remove grate, burner cap, and burner head to access the gasket
• Clean mating surfaces; seat the gasket flat and do not use sealants or adhesives unless specified by the manufacturer
• Reassemble, restore gas, and verify burner operation; leak-check with soapy water if any gas fittings were disturbed

A replacement gasket faceplate that seals the appliance faceplate to help keep out moisture, dust and debris while restoring a snug fit and reducing rattling. Fits select GE appliances as the factory-style replacement. What it does:

• Seals the faceplate to the cabinet, helping prevent drafts and moisture intrusion.
• Replaces worn, cracked or deformed gaskets that cause visible gaps or uneven fit.
• Helps reduce faceplate movement and rattling during operation.
• Use when you see splits, compression set, or persistent gaps around the faceplate.

• Disconnect power to the appliance and remove any panels necessary to access the gasket.
• Carefully remove the old gasket and clean the mating surfaces of adhesive, dirt and debris.
• Align the new gasket in the mounting channel and press into place; replace any damaged clips or fasteners.
• Follow the appliance service manual for model-specific steps.

This burner seal fits the 17k burner to restore a snug seal between the burner and cooktop, helping keep spills out of the burner assembly and keeping the flame properly aligned. Ideal for restoring a cleaner, more reliable cooktop surface. What it does:

• Creates a tight seal around the 17k burner to help prevent food and liquid from entering the burner cavity
• Keeps burner head seated correctly so the flame pattern stays consistent
• Helps reduce soot and residue buildup around the burner area
• Useful when the original seal is cracked, compressed, or missing

• One burner seal for a 17k burner (single piece)

• Always shut off power and gas supply before servicing the range
• Remove burner head and clean mating surfaces before installing the new seal
• Fit the seal in the correct orientation so the burner seats evenly; reassemble parts in reverse order
• After installation, restore power/gas and verify proper burner operation; follow manufacturer's instructions for leak checks and testing

This is a replacement refrigerator door gasket that restores the seal around the door to help maintain proper temperature and efficiency. It's a direct-fit sealing strip designed to replace a worn, torn, or deformed door seal. What it does:

• Seals the gap between the door and cabinet to help keep cold air in and warm air out
• Helps reduce frost buildup and prevents moisture and leaks around the door
• Restores consistent internal temperature for better food preservation
• Reduces compressor run time caused by an improper door seal

• One refrigerator door gasket

• Recommended: replace gasket on a clean, dry door surface; remove old gasket and adhesive residue before installing
• Use the manufacturer's recommended attachment method (snap-in or adhesive) for your model
• Inspect hinge alignment and door fit before finalizing gasket installation to ensure an even seal
• For safety, unplug the appliance or disconnect power before beginning repairs

This control panel gasket seals the appliance console to help keep moisture, grease, and debris out of the control area and maintain a tidy, responsive panel. It replaces worn or damaged seals that let contaminants reach electronics. What it does:

• Creates a protective seal around the control panel to reduce moisture and grime intrusion
• Helps prevent dirt and cooking residue from collecting under buttons and behind the console
• Reduces the chance of control panel corrosion and intermittent button response caused by contamination
• Restores a flush fit and finished appearance to the console area

• Disconnect power to the appliance before starting any repair to avoid shock or unexpected operation.
• Remove the control panel or console per the service manual to access the old gasket; follow OEM disassembly steps.
• Clean mating surfaces of old adhesive or debris before installing the new gasket for a secure fit.
• If adhesive is used, allow proper cure time and verify proper alignment before reassembly.

Black

This door gasket seals the broiler/bottom-oven door to help retain heat for more even broiling and reduce stray heat into the kitchen. It replaces worn or damaged seals that allow heat loss or uneven cooking. What it does:

• Creates a heat-tight seal around the broiler/bottom-oven door to improve cooking performance
• Helps prevent heat loss, uneven broiling, or extended cook times caused by gaps in the door seal
• Wear signs include visible cracks, flattened or torn material, and gaps around the door edge
• Replacing a damaged gasket can reduce smoke from burning food debris caught in a torn seal

• Disconnect power (and gas, if applicable) and allow the appliance to cool fully before starting
• Remove the broiler drawer or door per the owner's manual to access the gasket channel
• Clean the gasket channel of debris before seating the new gasket; press the gasket into the retainer evenly

A flexible replacement gasket that seals and side lamp glass, cushioning and securing the glass to help block moisture and debris from the lamp housing. Restores a tighter fit and reduces vibration or rattling around the lamp area. What it does:

• Seals the edge of the lamp glass to keep moisture, dust and food debris out of the lamp housing.
• Cushions and centers the lamp glass to reduce vibration and prevent rattling or glass movement.
• Helps maintain a stable lamp assembly so the light cover sits flush and stays in place.
• Use when the gasket is cracked, torn, deformed or missing, or when the lamp glass feels loose.

• Disconnect power to the appliance before servicing to avoid electrical shock.
• Handle lamp glass carefully to avoid breakage; wear gloves and eye protection as needed.
• Seat the gasket evenly around the lamp glass edge and press into the channel until fully seated; avoid stretching or deforming the seal.
• Replace only with the exact OEM part number to ensure correct fit and sealing.

This 65-inch door gasket seals the appliance door to help maintain proper temperature and prevent leaks. It replaces a worn or torn gasket to restore a tight seal and improve efficiency. What it does:

• Creates an airtight seal around the door to help prevent water leaks and air loss
• Helps maintain consistent internal temperature and protect contents
• Reduces drafts and minimizes moisture buildup that can cause odor or frost
• Common symptom: visible cracks, tears, flattening, or water leaking from the door

• Install on a clean, dry door surface; follow OEM alignment to ensure an even seal
• Inspect door frame and mounting channel for damage before installing the new gasket
• Gasket may need gentle warming or seating to fit snugly in the channel (avoid open flame)
• Disconnect power/water if removing door panels or working near electrical components