Range / Cooktop / Oven Hinge Parts

This door hinge supports and guides the appliance door so it opens and closes smoothly and stays aligned with the latch and gasket. Replacing a worn hinge restores proper fit and closing action to reduce rubbing and poor sealing.

• Provides the pivot point and supports the door's weight during operation
• Maintains alignment for an even gap and consistent seal
• Helps correct sagging, scraping, or a door that won't close flush
• Common signs of wear: bent/cracked hinge, squeaking or popping, misalignment

• Disconnect power before servicing and support the door to prevent strain or damage
• Remove mounting fasteners; transfer any reusable screws, spacers, or covers from the old hinge
• Install and snug fasteners, then check door alignment and closure; adjust as needed
• Open and close the door several times to verify smooth operation and recheck fasteners

This oven door hinge restores smooth, controlled movement so the door opens easily and closes fully for a reliable seal. Replacing a worn hinge helps reduce heat loss and supports consistent cooking performance and safe operation.

• Provides the pivot and spring-assisted action for opening and closing the oven door
• Helps pull the door closed and hold it at intended stop positions
• Maintains even gasket contact to keep heat inside the cavity
• Common symptoms of a failing hinge: door won't close fully or sit flush, drops or slams open, binds or pops when moving, or shows an uneven gap

• Disconnect power and allow the oven to cool completely before servicing
• Support the door; open to the removal position and release hinge locks, then lift the door off
• Use caution—hinge springs are under tension; wear hand and eye protection
• Install in the same orientation and verify door alignment and smooth operation after reassembly

This oven door hinge restores smooth, controlled door movement and a proper seal. Worn hinges can cause a sagging door, poor closure, or binding—replacing the hinge helps maintain safe operation and consistent cooking performance.

• Supports the oven door with a spring mechanism for controlled opening and closing
• Helps pull the door tight against the gasket for an effective seal when closed
• Works with the opposite hinge to keep the door aligned and stable
• Common symptoms include door not closing fully, sagging or dropping, hard-to-open/close action, or heat escaping around the door

• Disconnect power and allow the oven to cool completely before servicing
• Remove the door following your model's instructions; engage hinge locks or use retaining pins if provided
• Replace the hinge in the same orientation; ensure hinge arms are fully seated in the receivers
• Reinstall the door and verify smooth motion and a complete seal

Right Side

The Door Hinge is an OEM part for GE wall ovens. It acts as the pivot point that allows easy opening and closing of the oven door during use. The durable hinge is responsible for securely yet smoothly swinging the oven door into position.

Causes of failure can be normal wear and tear over extended use. Frequent opening and shutting of a heavy oven door places considerable stress on the hinge. Accidental damage from overloading or impact can also negatively affect performance.

Symptoms of a bad hinge include:

• Difficulty opening or closing the oven door
• Excessive friction or resistance at the hinge
• Noises or squeaking emanating from the hinge area
• Visual defects such as cracks, bending, or loose/missing hardware

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Oven door hinge is an OEM part for GE ranges. This right side hinge is responsible for securely and smoothly opening and closing the oven door. It allows for comfortable access in and out of the oven cavity.

Causes of a bad hinge can include wear and tear from repeated opening and closing of the door over time, stress from excessive weight on the door, or damage from impact.

Symptoms of a bad hinge include:

• The door not opening or closing properly
• Increased resistance or hesitation when operating the door
• Loosening or sagging of the door
• Uneven gaps around the door frame

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is a replacement door hinge that restores secure, stable opening and closing for compatible appliance doors. It provides a direct-fit repair to stop sagging or misaligned doors and improve safe operation. What it does:

• Supports and guides the appliance door for smooth open/close operation
• Replaces worn or bent hinge hardware that causes door sag or uneven gaps
• Helps stop rubbing, catching, or scraping when the door moves
• Restores proper door alignment that can affect sealing and function

• One replacement hinge

• Disconnect power (or unplug) and shut off water if applicable before starting repairs
• Inspect mounting screws and strike plates; replace any damaged fasteners for secure fit
• Tighten hardware evenly and check door alignment during reassembly

This right-side refrigerator door hinge replaces a worn or damaged hinge to restore correct door alignment and smooth opening. It's a direct-fit hinge used where the door is sagging, binding, or not sealing properly. What it does:

• Supports the right-hand door and provides a pivot point for opening and closing
• Restores proper door alignment to improve sealing and temperature consistency
• Reduces binding, scraping or noisy operation caused by a bent or worn hinge
• Helps prevent accelerated wear to the door and cabinet mounting surfaces

• Disconnect power to the appliance and remove stored items from the door before starting.
• Support the door while removing and installing the hinge to prevent damage or injury.
• Use the correct hand tools and tighten fasteners to the manufacturer's torque recommendations.
• If alignment issues persist after installation, check hinge placement and door stops per service instructions.

This left-side refrigerator door hinge secures and guides the door on compatible GE refrigerators, helping the door open and close smoothly and maintain proper alignment. Replacement hinge restores stable door movement and sealing. What it does:

• Provides a reinforced pivot point so the door swings freely without sagging
• Keeps the door aligned to preserve gasket contact and cooling performance
• Replaces worn or bent hinges that cause uneven gaps or noisy operation
• Works as part of the door mounting system to support normal door weight

• One left-side door hinge

• Disconnect power to the appliance and remove stored items from the door before starting
• Support the door while removing hinge fasteners to prevent dropping or damage
• Retain original screws and hardware unless the replacement explicitly includes them

The Door Hinge (Right) is an OEM part for GE gas ranges. It acts as the pivot point allowing the right side of the range door to smoothly and securely open and close.

Causes include normal wear and tear from repeated use, accidental impacts deforming the hinge, or deterioration of spring components.

Symptoms of a bad right door hinge include:

• Resistance felt only when opening/closing the right side of the door  
• Noise, rubbing or squeaking coming from the right hinge area
• Visual bending or damage evident on the hinge itself
• Improper alignment of just the right side causing sealing issues

This OEM replacement is compatible with Hotpoint, RCA, and select Kenmore gas range models.

This right-side hinge assembly secures and guides the appliance door for consistent opening and closing, restoring proper alignment and sealing. It's a direct-fit replacement when the door feels loose, binds, or won't stay aligned. What it does:

• Supports the door on the right side and maintains correct pivoting motion
• Restores proper door alignment to improve closing and sealing
• Helps eliminate sagging, binding, or uneven gaps during operation
• Works with existing hinge pins and mounts where applicable

• Replace both hinges if the left-side hinge shows similar wear; balance is recommended for long-term alignment
• Disconnect power and remove any panels or door components per manufacturer instructions before starting
• Use proper tools and keep fasteners organized; tighten to OEM torque if specified