Range / Cooktop / Oven Oven Control Or Thermostat

This electronic control board regulates your appliance's main functions and user interface, restoring responsive controls and automatic operation when the original board has failed. It replaces a faulty control to help bring back normal performance. What it does:

• Receives input from control buttons and sensors and sends commands to components
• Manages timed cycles, temperature regulation, and other automated functions
• Can stop controls from responding or cause incorrect cycle behavior when failing
• Symptom-safe examples: unresponsive display/buttons, incorrect cycles, or erratic operation

• Disconnect power to the appliance before starting any work
• Handle the board carefully to avoid ESD (static) damage; wear an anti-static wrist strap if available
• Note connector locations and take photos before disconnecting wiring for correct reassembly

The Thermostat is an OEM part for GE gas ranges. It regulates temperature settings for gas burners and oven elements. 

Causes of a bad thermostat can include worn contacts, loose terminals, or moisture damage degrading electrical pathways over time.

Symptoms of a faulty thermostat include:

• Inability to ignite or light gas burners 
• Faulty or unresponsive oven/burner temperature knobs
• Inconsistent or unstable heating from specific burners 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore gas range models. 

A safety thermostat that monitors and limits temperature at the range/stove backguard to help prevent overheating. Replaces a failed safety limiter to restore proper temperature control and safety operation. What it does:

• Acts as a temperature-limiting safety device for the range backguard assembly.
• Opens the circuit when temperatures exceed safe limits to prevent overheating.
• Commonly replaced when the oven or control fails to maintain temperature or shuts off unexpectedly.
• Helps address overheating, intermittent heating, or safety-trip symptoms tied to the backguard area.

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Access may require removing the backguard panel and control housing; keep track of fasteners and wire routing.
• Verify electrical connections are secure and intact; replace only with correct part number.

 The Thermostat is an OEM part for Whirlpool microwaves. It is a temperature-sensitive component that monitors heat levels inside the oven cavity during operation.

Causes may include damage from exposure to moisture or debris over time that disrupts accurate readings.

Symptoms of a faulty thermostat include:

• Incomplete or inconsistent heating with uneven hot/cold spots
• Food not reaching expected doneness after preset times
• Overheating errors or cycle interruptions

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This high-limit thermostat (hi-limit switch) is a temperature safety device that stops the heating circuit if the appliance overheats, helping protect the unit and restore proper heat control when replaced. What it does:

• Opens the heating circuit if internal temperature exceeds safe limits to prevent overheating.
• Controls whether the heater/element receives power based on temperature.
• When faulty, common symptoms include no heat or intermittent heating and repeated thermal cutouts.
• Can be tested for continuity to confirm electrical function.

• One high-limit thermostat (hi-limit switch).

• Disconnect power before inspecting or replacing; risk of shock or injury if energized.
• Note and label wire locations or take a photo before removal for correct reassembly.
• Verify part compatibility with your model before installing; confirm continuity after installation.

This oven thermostat regulates baking and roasting temperatures on non-self-cleaning ranges so your oven heats to the set temperature. Designed to restore accurate temperature control and consistent cooking results. What it does:

• Senses oven temperature and signals the control to cycle the heating element on and off
• Helps correct ovens that run too hot, too cold, or show inconsistent temperatures
• Supports basic mechanical temperature control on non–self-clean models
• Commonly used when the oven won't maintain set temperature or cooking results vary

• Disconnect power to the range before replacing this part to avoid electric shock
• Handle the thermostat capillary and probe carefully — avoid kinks or sharp bends
• Verify temperature with an oven thermometer after installation

This oven thermostat senses oven temperature and signals the control system to maintain set heat levels for consistent cooking. It replaces a failed temperature-sensing control to help ovens reach and hold desired baking and roasting temps. What it does:

• Regulates oven temperature by opening/closing the thermal switch at set points
• Helps correct symptoms like oven not heating, overheating, or temperature fluctuations
• Works with the oven control and heating elements to stabilize cooking temps
• Mechanical design suited for direct temperature sensing inside the oven cavity

• Disconnect power to the range before attempting any service to avoid shock
• Access may require removing the oven back panel or control panel; follow the service manual
• Handle the temperature sensing probe and capillary tube carefully to avoid kinks or damage

This mechanical temperature control thermostat replaces a failed refrigerator control that cycles the compressor to maintain proper internal temperature. Restores reliable on/off switching so the appliance can hold set temperatures. What it does:

• Senses cabinet temperature and opens/closes the compressor circuit to regulate cooling
• Stops extended compressor run or prevents compressor from starting when thermostat fails
• Addresses symptoms such as warm refrigerator, inconsistent temperatures, or excessive cycling
• Works with mechanical control systems that use a physical sensing element

• Disconnect power to the appliance before starting any work
• Access may require removing the control housing or inner cabinet trim; keep track of fasteners
• Handle the sensing element gently; avoid kinks or sharp bends in the capillary/sensing tube