Need Help?
Call or text
If your range burner won't turn on or off properly, or the indicator light stays on when turned off, this infinite switch restores control. DIY repair.
Remove front panel and replaced. Received parts fast. Read more
Replace a non-functioning oven light switch that won't illuminate the cavity. Simple DIY repair—typically takes 15-30 minutes with basic tools.
Removed & replaced igniter switch assembly. The hardest part was figuring out how to remove the range top...look up a YouTube video with your manufacturer and model number to see how to do it. Read more
Fix a burner stuck on high or that won't heat properly with this cooktop infinite switch. Restores accurate temperature control. 30-minute DIY repair.
This cooktop has a dual element with an inner burner surrounded by an outer burner. The switch controls either the inner burner alone or both. The switch failed in that it would not operate the inner burner by itself, both burners would come on and only on high. On 8/14/2014 I replaced the failed dual element switch as follows: • Turned power off to cooktop. • Removed unit from cabinet. • Removed metal edging and glass top. • Removed screws holding switch panel access underside. • Removed old... Read more
Burner won't turn off or element light stays on? This range burner control switch regulates temperature and power. Moderate DIY repair, 30-60 minutes.
I went on your website found the parts needed to make the repairs. I watched the short video on installation. The parts arrived just a few days after I placed the order. I finished the repair in less than an hour and had to wait a few minutes to test the switch since the power was off and on due to a wind storm. Simple easy to do repair and I saved $90.00 on service fee for a tech to do the repair. Read more
Fix a burner stuck on high or won't adjust temperature with this infinite switch. Controls cooktop burner heat levels. DIY repair in under 30 minutes.
Replaced the Infinite Switch and that solved the problem. Did not need to replace the Surface Element Read more
Fix a burner that won't turn off or heat properly with this dual infinite switch. Controls both inner and outer element rings. Moderate DIY repair.
Relatively easy DIY Read more
Burner won't heat, stuck on high, or works intermittently? This cooktop burner control switch restores reliable on/off control. Easy DIY repair.
Replaced the switch Read more
If your triple burner stays on high or won't adjust temperature, this infinite switch restores precise heat control for small, medium, and large rings.
Replace switch Read more
Oven light won't turn off when door closes? This door-mounted light switch is often the culprit. Easy 5-minute fix—just unplug power and swap it out.
When trouble shooting the problem I found that the light switch housing outer lip was broken allowing the switch to push through mounting surface behind the oven door. This is a slide in range so, I proceeded to pull the range away from the counter where I could unplug the power cord. Once the power was off like located the panel on the right upper side of the unit and removed the screws to allow access to the switch. I then unplugged the switch from the wiring harness and removed the damaged... Read more
Burner won't ignite or fires intermittently? This gas range igniter switch assembly detects spark signals to light burners. DIY-friendly repair.
Found a YouTube video online that provided instruction on how to change out the part. Read more
Oven won't heat or fan won't run? This high-amp SPDT switch routes power to locks, relays, and fans. Fixes intermittent operation. Moderate DIY fix.
Replaced faulty latch with new latch. New latch was different configuration, but the fit was okay. The only issue was that the wires to the electric motor were just barely long enough. Overall easy repair if you have a T15 Torx bit, phillips screwdriver, and 1/4" nut driver. Hardest part is removing the gas cooktop to gain access to the cleaning latch. 0. Turn off electric to stove; remove the cast iron grates, center caps/orifices, and catch pans from the stovetop. 1. Disconnect the... Read more
If your range burner won't heat, cycles incorrectly, or buzzes when turned on, a faulty infinite switch is likely the cause. Moderately easy DIY repair.
Had to replace both switches. The hard part was getting the control panel off to get access. Only a few screws but even after getting them out, really struggled getting it off. After getting off, discovered that you need to get it lifted up before pulling it off. Read more
Fix an oven light that won't turn off or controls that don't respond. This control panel switch restores reliable on/off function. DIY-friendly repair.
Replaced switch. Read more
Fix sparking or non-working igniter switches with a new switch harness. Connects control switches to cooktop wiring. Moderate DIY repair, 1-2 hours.
I replaced the igniter module. Read more
Fix unresponsive or erratic burner controls with this rotary sensor. Restores accurate knob response when settings don't match heat output. Advanced repair.
I ordered all the parts from AppliancePartsPros.com and in two days I had every new part that was. Ordered. After being told from the appliance repair company that I wouldn’t get parts for months. I received all parts within 4 days, 19 different parts! Read more
Burner stuck on high or won't regulate temperature? The infinite switch controls heat levels. Common DIY repair, typically 10 minutes to install.
I watched an 8-minute video on YouTube. Identified and ordered the part from AppliancePartsPros that a $12 shipping fee was received in 2 days. Took 10 minutes or less to install. Years ago without next-day parts and YouTube, this $60 repair would have cost me $200+. Read more