Range Panel Parts

This replacement storage drawer lining protects the drawer floor and keeps stored items stable—helpful for worn, stained or missing liners. It restores a clean, non-abrasive surface so drawers look and function like new. What it does:

• Provides a protective surface that helps prevent scratches, stains and wear to the drawer floor
• Reduces item shifting and sliding inside the drawer
• Helps contain minor spills and makes cleanup easier
• Restores a finished appearance when the original liner is damaged or missing

• Remove drawer and thoroughly clean and dry the drawer floor before installing
• Align the liner with the drawer edges and press into place; trim only if explicitly required by model
• No special tools usually required; keep fingers clear of edges when fitting
• Dispose of the old liner according to local regulations

This oven door glass assembly replaces damaged or cracked door glass to restore a clear viewing window and help keep the oven cavity sealed. It's a direct-fit replacement for affected Frigidaire oven doors. What it does:

• Replaces cracked, chipped or broken oven door glass to restore safe, visible operation.
• Lets you monitor cooking without opening the door to prevent heat loss from frequent door openings.
• Helps the door maintain its sealed barrier for more consistent oven performance.
• Matches OEM form for straightforward fit and alignment when installed correctly.

• Disconnect power (and gas if applicable) before starting; handle glass with thick gloves and eye protection.
• Installation may require removing the oven door and several screws—keep parts organized and follow OEM instructions.
• Inspect door seals and mounting hardware while replacing the glass; replace any damaged components.

Color: White

This backsplash restores the rear trim behind a range or cooktop, protecting the wall and covering wiring openings for a clean, factory-look finish. It replaces a damaged, dented, or missing backsplash to improve safety and appearance. What it does:

• Covers the gap between the cooktop and the wall to block spills, splashes, and heat from reaching the wall surface
• Hides wiring and mounting holes for a neat, finished look
• Replaces bent, cracked, or corroded rear trim that can collect grease and grime
• Helps maintain proper clearance and original appearance of the appliance

• One single-piece backsplash

• Basic hardware and mounting locations are OEM-specific; confirm matching fasteners on arrival
• Turn off power to the appliance and move the unit away from the wall before removing or installing the backsplash
• Use care to avoid scratching the finish during installation; two people may be needed for larger ranges
• If mounting holes or brackets are damaged, replace those items before installing this backsplash

The Range Sub Control Assembly is an essential component for maintaining the functionality of your Samsung range. This genuine OEM part ensures seamless control over your appliance, allowing you to adjust temperatures and settings with ease. Designed specifically for Samsung ranges, it guarantees a perfect fit and reliable performance. By replacing a faulty sub control assembly with this high-quality part, you can restore your range to its optimal working condition without the need for a complete replacement. The Range Sub Control Assembly enhances the overall performance of your kitchen appliance, providing precise control and improving your cooking experience. Its durable construction ensures long-lasting use, making it a cost-effective solution for appliance repair. Whether you're dealing with unresponsive controls or inconsistent heating, this genuine OEM part offers the reliability and efficiency you need. Trust the Range Sub Control Assembly to deliver exceptional results and keep your Samsung range running smoothly for years to come.

This heat deflector directs and shields heat inside the appliance to help protect surrounding components and maintain proper airflow. It's a simple replacement for torn, warped, or missing deflectors. What it does

• Redirects heat away from sensitive components to reduce risk of heat damage
• Helps maintain consistent airflow paths for proper appliance performance
• Commonly replaced if warped, cracked, melted, or dislodged
• May reduce odors or burning smells caused by contact with hot parts

• Disconnect power (and gas, if applicable) before beginning any repair
• Inspect surrounding mounting points and replace any damaged fasteners if needed
• Handle carefully—sharp edges may be present

This control panel assembly replaces a worn or damaged front touch/control surface and restores proper user controls and display visibility on the range or oven. Designed to match original fit and appearance. What it does

• Houses the touch buttons, display window and associated front-facing controls used to set oven functions and temperatures.
• Replaces cracked, faded, or unresponsive control surfaces that can interfere with entering settings or reading the display.
• Restores a secure, finished face for the console and helps protect internal control electronics.
• Compatible with service-side mounting and connects to the internal control board via factory wiring harnesses.

• Handle carefully to avoid scratching the finished face; use soft gloves if available.
• Disconnect power at the breaker or unplug the appliance before beginning any service.
• Installation typically requires removal of the oven/range console trim and attachment screws; keep fasteners for reuse.

This replacement drawer panel restores the finished front appearance of the appliance drawer and covers the drawer opening for a clean, like-new look. It's a direct-fit cosmetic panel made to match the appliance's original finish. What it does

• Replaces a cracked, dented, scratched, or faded drawer front to restore appearance
• Covers and protects the drawer opening from dust and debris
• Provides the correct mounting surface for existing trim, handles, and clips
• Helps maintain consistent appearance across the appliance front

• High-level replacement; remove drawer assembly to access mounting screws or clips
• Keep small fasteners and mounting clips; verify orientation before tightening
• Use hand tools and avoid over-tightening to prevent panel damage
• Follow safety procedures and disconnect power if instructed by the manufacturer

This is the oven's bottom broiler pan that catches drips and supports broiling cookware for safer, cleaner cooking. It restores the oven's drip containment so you can broil and roast without excess mess. What it does:

• Catches grease and food drippings to help prevent spills and oven fouling
• Provides a stable surface for broiling pans and racks during high-heat cooking
• Helps reduce flare-ups by containing drips below the food
• Useful when replacing a worn, dented, or missing oven pan

• Allow the oven to cool and disconnect power before removing or installing the pan.
• Slide the pan into the oven bottom on the support ledges; no tools required for typical installation.
• Clean pan after each use per your oven manual to avoid heavy buildup; use non-abrasive cleaners to protect surface.
• Replace if pan is warped or damaged to ensure proper fit and performance.

This control panel is the exterior trim that houses and protects the oven/range user interface and display, restoring a clean, functional front for the appliance. It keeps buttons and indicators secure and visible for reliable operation. What it does:

• Covers and protects the appliance control buttons, touchpad, and display from spills and damage
• Provides the visible interface for selecting oven functions and viewing status
• Restores a finished appearance to a damaged, cracked, or worn control area
• Helps ensure buttons and indicators align properly for correct operation

• One control panel

• Disconnect power to the appliance before beginning any repair to avoid shock or injury
• Some models require removing screws or snap clips and gently lifting the old panel from the console
• Handle the panel carefully to avoid scratching the visible finish or bending mounting tabs
• If the panel attaches to electronic components, take care not to damage ribbon cables or connectors; take care not to damage ribbon cables or connectors.

This oven bottom pan replaces the removable bottom tray that catches spills and protects the oven floor, restoring an even surface for cooking and easier cleanup. Fits in the lower cavity under the oven racks. What it does:

• Provides a durable, porcelain-coated surface to catch drips, crumbs and spills during baking and roasting
• Helps prevent spills from contacting the oven floor and heating elements
• Restores a flat, stable cooking surface for pans and bakeware
• Can reduce time spent scrubbing baked-on messes when used with proper liners

• One oven bottom pan

• Allow the oven to cool completely and disconnect power before replacing the pan
• Remove oven racks, slide out the old pan, then slide the replacement into the same position
• No special tools typically required; handle carefully to avoid chipping the coating

This replacement cabinet frame restores the appliance's front trim for a clean, finished appearance and proper panel alignment. It helps keep edges covered and maintains the door/cabinet fit. What it does:

• Provides the front trim/frame that supports and aligns the appliance cabinet or door panels
• Covers exposed edges for a finished look and helps reduce drafts or light gaps
• Helps eliminate rattling or misalignment caused by a damaged or warped frame
• Matches OEM fit to replace a cracked, bent, or cosmetically damaged frame

• Disconnect power (and water for appliances with water) before beginning any work
• Basic hand tools typically needed; retain all fasteners from the original part for reassembly
• Handle carefully to avoid scratching the finish; check fit before tightening fasteners