Need Help?
Call
Burner stuck on high or not heating? This infinite switch regulates cooktop burner power. Typical DIY repair takes about 30 minutes with basic tools.
Ordered infinity switches for both rear stove top elements and replaced them in about a half hour. I have experience with a variety of appliance repair, so this was a snap. Parts are genuine and were exact to the originals replaced. I received the parts the very next day after I placed the order. Now that's fast shipping! Read more
Burner won't turn off or element light stays on? This range burner control switch regulates temperature and power. Moderate DIY repair, 30-60 minutes.
I went on your website found the parts needed to make the repairs. I watched the short video on installation. The parts arrived just a few days after I placed the order. I finished the repair in less than an hour and had to wait a few minutes to test the switch since the power was off and on due to a wind storm. Simple easy to do repair and I saved $90.00 on service fee for a tech to do the repair. Read more
Fix burners that won't spark or click constantly. This igniter switch wiring harness restores reliable lighting on gas ranges. DIY-friendly repair.
I replaced the switch/wire harness that connects to the gas valves. Read more
Fix a burner that won't turn off or heat properly with this dual infinite switch. Controls both inner and outer element rings. Moderate DIY repair.
Relatively easy DIY Read more
Burner won't heat or stays stuck on? This surface element rocker switch restores reliable on/off control. Simple DIY repair—just 4 screws, 30 minutes.
Worst part of job was sliding stove out from wall. Remove 4 small screws from shield on top of stove, disconnect two connectors from switch rocker, push lock tabs inward so you can push switch rocker outward from back toward burners threw frame of stove, insert new unit until click locks, reconnect wires, and reinsert shield back on top stove and secure with 4 screws removed earlier. Easy job, part shipped from AppliancePartsPros.com Fedex ASAP. Read more
This assembly includes the spark ignition switches and wiring harness that control the igniter circuits on a gas range or cooktop. The switches detect burner position and signal the igniters to spark when a burner knob is turned. Replace this assembly if burners fail to ignite, click continuously without lighting, or if the spark module does not activate consistently.
My husband and myself didn't agree on which part was the exact problem. He felt it was the valve. I felt it was the ignitor/ orifice. And we both agreed the Harness-Ignitor needed to be replaced. So we ordered all 3, and I'm not sure if in fact all three were needed or not, but now with those parts replaced, the range is working like brand new!! Thanks to all the videos and diagrams on the website we were able to fix it ourselves easily. And the price was cheaper then other websites, also it... Read more
Burner won't turn off or stays on high? This infinite switch controls power to your surface element. Moderate DIY repair restores heat control.
Disconnected ( already tripped) breaker in the panel. Lifted cooked top unscrewed the glass top and set aside. I took the picture of the wires connected to the control on my ipad and replaced broken control. reconnected the wires as per picture. Cleaned the greased glass top and replaced the infinite switch seal for the broken control. Then reinstall glass top back on the cooktop and put the cooktop back in in place. Enable breaker in the panel and now i have good working cooktop again. ( do... Read more
Fix a burner stuck on high or won't adjust temperature with this infinite switch. Controls cooktop burner heat levels. DIY repair in under 30 minutes.
Replaced the Infinite Switch and that solved the problem. Did not need to replace the Surface Element Read more
The Rocker Switch is an OEM part for Frigidaire ranges and ovens. It is responsible for turning the interior oven light on and off. The light switch allows visibility of the oven cavity for viewing food during the cooking process.
Causes can include normal wear and tear over time, exposure to heat inside the oven cavity, or accidental damage.
Symptoms of a bad oven light rocker switch include:
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Removed & replaced igniter switch assembly. The hardest part was figuring out how to remove the range top...look up a YouTube video with your manufacturer and model number to see how to do it. Read more
Fix a burner stuck on high or that won't heat properly with this cooktop infinite switch. Restores accurate temperature control. 30-minute DIY repair.
This cooktop has a dual element with an inner burner surrounded by an outer burner. The switch controls either the inner burner alone or both. The switch failed in that it would not operate the inner burner by itself, both burners would come on and only on high. On 8/14/2014 I replaced the failed dual element switch as follows: • Turned power off to cooktop. • Removed unit from cabinet. • Removed metal edging and glass top. • Removed screws holding switch panel access underside. • Removed old... Read more
Provides electrical connection and control for gas burner ignition on cooktop surfaces. Replace if burners won't light, produce weak sparks, or if you hear clicking without ignition.
I called a rpair service. The men came to the house, torn apart the stove top and advised Replacement of the wire harness. The trip charge of $100 would be deducted from a repair bill of $350, thus they needed an additional $150 for parts and $100 for labor after paying the trip charge. I bought the harness for $60, and the star bits I needed for my drill for $10. My son and I installed the new harness in about 30 minutes, which included a thorough cleanup, saving us $180. Read more
The Door Switch is an OEM replacement part for Frigidaire wall ovens. It is a component located on the oven door that detects when the door is opened and closed. The door switch works alongside the control board to regulate oven operations based on door position.
Symptoms of a bad door switch can include:
Causes relate to normal wear over extended use as the door switch mechanism cycles with frequent door openings and closings. Moisture exposure or impacts could also degrade switch performance.
This OEM Frigidaire switch is compatible with Amana, Jenn-Air, KitchenAid, and some Electrolux wall oven models as well.
I diagnosed this problem via the web and the advice was spot on. The problem was a failure of the bottom door switch. I used a multimeter to verify that the switched never closed properly. It took me a minute to figure out how to remove the old switch (press a release tab under the switch while simultaneously rotating counter-clockwise). That was about the most difficult part of the repair. Read more
Oven won't change modes or burner won't heat? The selector switch routes power to cooking functions. Moderate DIY repair with video guidance available.
My cooktop repair was a total success from start to finish. I reviewed and later followed the APP repair video, which helped me decide if I wanted to tackle the repairs and guided me right before I started. The APP phone staff member was very helpful verifying the parts I had identified online using the model number of my older GE Profile cooktop to locate and view the correct online exploded view diagram. I told him it was a pleasure working with him. The parts arrived within 3 days of... Read more
This is a spark ignition switch assembly with wiring harness that controls the electric igniters on a gas range cooktop. It sends voltage to the spark modules when a burner knob is turned, initiating the clicking ignition sequence. Replace this part if your burners won't spark when turned on, spark continuously even when knobs are in the off position, or if only some burners ignite properly.
Found a YouTube video online that provided instruction on how to change out the part. Read more
6" element switch
Talked to a representative at your company they said it was probably the infinite switch. I purchased all four switches, replaced all four burner switches. Very easy to do. In less than an hour to replace all four. Read more
This is a high-amp SPDT (single pole, double throw) switch used in the oven door mechanism. It detects whether the oven door is open or closed and signals the control to enable or disable certain functions such as the oven light or broil element. Replace this switch if the oven light does not turn on or off when the door is opened or closed, or if the oven does not operate correctly in relation to door position.
Replaced faulty latch with new latch. New latch was different configuration, but the fit was okay. The only issue was that the wires to the electric motor were just barely long enough. Overall easy repair if you have a T15 Torx bit, phillips screwdriver, and 1/4" nut driver. Hardest part is removing the gas cooktop to gain access to the cleaning latch. 0. Turn off electric to stove; remove the cast iron grates, center caps/orifices, and catch pans from the stovetop. 1. Disconnect the... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.