Range Switch

This switch assembly is the door lock mechanism for select front-load washers. It detects when the door is closed and locks it during operation, allowing the washer to start and run safely without interruptions.

• Monitors door position and signal
  This part fixes the following symptoms

  • Doesn't shut off
  • Gas igniter glows, but will not light

  See more...
  Do-It-Yourself Stories from Customers like You All the igniters spontaneously began to fire   Michael S. • Adams , NY • October 12, 2019

  Found a YouTube video online that provided instruction on how to change out the part. Read more

Burner stuck on high or won't adjust temperature? This range infinite switch controls surface element heat levels. Common DIY fix for uneven heating.

This high-amp SPDT switch routes power between circuits in cooking appliances to control items such as locks, element relays, or fans. Replacing a worn switch restores dependable operation and helps eliminate intermittent on/off issues. What it does:

Do-It-Yourself Stories from Customers like You Faulty self cleaning latch   Gregory K. • Bel Air , MD • December 28, 2016

Replaced faulty latch with new latch. New latch was different configuration, but the fit was okay. The only issue was that the wires to the electric motor were just barely long enough. Overall easy repair if you have a T15 Torx bit, phillips screwdriver, and 1/4" nut driver. Hardest part is removing the gas cooktop to gain access to the cleaning latch. 0. Turn off electric to stove; remove the cast iron grates, center caps/orifices, and catch pans from the stovetop. 1. Disconnect the... Read more

Fixes burner stuck on high, won't heat, or uneven heating. This infinite switch regulates surface element power for precise temperature control.

If your range burner won't heat, cycles incorrectly, or buzzes when turned on, a faulty infinite switch is likely the cause. Moderately easy DIY repair.

This control-panel switch restores reliable on/off control of a selected function on your range or wall oven. Replacing a worn or intermittent switch helps ensure the appliance responds consistently when you toggle that function.

• Directs power t
  Do-It-Yourself Stories from Customers like You Defective door light switch. When temp would cool off, the switch would click on and off during heat up or cool down period   Joseph W. • Summit , MS • July 22, 2019

  Replaced switch. Read more

Fix sparking or non-working igniter switches with a new switch harness. Connects control switches to cooktop wiring. Moderate DIY repair, 1-2 hours.

This potentiometer is the rotary sensor behind the control knob. It converts knob rotation into an electrical signal the control board uses to adjust settings, restoring smooth, accurate response when a worn or erratic control causes inconsistent operatio

Burner stuck on high or won't regulate temperature? The infinite switch controls heat levels. Common DIY repair, typically 10 minutes to install.

Oven light stays on or won't turn on when door opens? This door-activated switch restores automatic light control. Easy 15-minute DIY repair.

If your burner indicator light stays on constantly or burner runs at full heat on all settings, this infinite switch controls heat levels. 10-minute fix.

Fixes burner that won't heat or indicator light stuck on. This infinite switch controls surface burner power and heat settings. Moderate DIY repair.

Fix intermittent burner failures or electrical issues with this range wiring harness. Restores power flow when connections are loose, burnt, or broken.

Fix a burner that won't heat or has no temperature control by replacing this 6-inch element switch. Restores smooth low-to-high heat adjustment in 30 minutes.

The fan control switch is the panel-mounted switch that sends power to the appliance's fan motor. Replacing a worn switch restores reliable on/off control and proper airflow so the fan starts and stops when it should.

• Provides user-operated on/o
  Do-It-Yourself Stories from Customers like You The fan switch on our jenn air cooktop broke   Jonathan B. • Bend , OR • March 29, 2015

  After looking at several YouTube videos that were only moderately helpful for my particular model, I disconnected the power at the breaker, disconnected the wires below the cooktop to the junction boxed lifted the whole unit out, including the fan assembly. I flipped it upside down and took off the screws holding the unit to the glass top. Although the new fan switch did not look the same as the original switch, the new switch does fit. The new switch did not come with a hex nut. The old hex... Read more

If your gas burner won't light or clicks continuously, this igniter switch mounts on the valve stem to restore reliable ignition. Takes 5 minutes to replace.