Range Fuse Or Sensor

Oven won't heat or element burned out? This high-temperature cut-out fuse interrupts power when temperatures exceed safe levels. Often fails with elements.

Oven won't heat after self-clean cycle? A faulty limit switch prevents operation when stuck open. Tests quickly with a multimeter for continuity.

Fix a burner that overheats or won't turn off. This surface element limiter switch monitors temperature and prevents damage. Direct replacement part.

This 250V, 1A fuse protects your washer's control circuit from overcurrent. Replacing it can restore control power once the root cause is corrected.

• Opens to protect electronics when current exceeds its 1A rating
• Check this part if the washer has no power, the control panel is dead, or it won't start
• A blown fuse will test open for continuity
• Repeated failure points to an underlying short or component fault that must be fixed

• Disconnect power before servicing
• Access the fuse at the control board or fuse holder
• Replace only with the same rating: 1A, 250V
• Inspect wiring/components and correct any short before restoring power

Primary limit switch that interrupts the heating circuit when temperatures exceed safe limits to prevent overheating. Replacing this switch restores the appliance's temperature safety control and helps return normal heating behavior. What it does:

• Monitors temperature and breaks power to the heating element when the preset limit is reached.
• Acts as a safety cutoff to help prevent overheating and related damage.
• A failed-open switch commonly causes no heat or intermittent heating.
• A failed-closed switch can allow excessive heat or repeated thermal trips.

• Disconnect power before servicing to avoid shock or injury.
• Note terminal locations and wiring before removal; reconnect each wire to its original terminal.
• Handle the part and terminals carefully to avoid damage; secure fasteners firmly but do not overtighten.

Fixes F1 or F2 error codes and prevents overheating in ovens. This safety switch monitors temperature limits to protect components. Direct fit part.

Microwave shuts down during use? This thermal cutoff thermostat prevents overheating by interrupting power when temperatures exceed safe limits.

Oven won't heat properly or overheats after self-cleaning? A faulty lower thermostat often causes temperature regulation issues. Moderate DIY repair.

Replaces the refrigerator temperature control thermostat to restore consistent cooling. This direct-replacement thermostat helps regulate compartment temperature so food stays at the set level and reduces temperature swings. What it does

• Senses compartment temperature and switches the cooling system on and off to maintain the selected temperature range.
• Helps prevent temperature fluctuations that can cause food to spoil or freeze unexpectedly.
• Commonly used when the refrigerator runs continuously, won't reach set temperature, or cycles erratically.
• Works with the existing control knob and wiring—intended as a like-for-like replacement.

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Basic hand tools are typically required; take care not to damage the sensor bulb or capillary if present.

The Microwave Thermostat is a reliable component designed to regulate temperature in your microwave, ensuring optimal performance and safety. This genuine OEM part is specifically compatible with a wide range of Samsung microwave models, providing a secure and precise fit. By maintaining the correct temperature levels, the Microwave Thermostat helps prevent overheating and extends the lifespan of your appliance. Installing the THERM thermostat restores your microwaveGÇÖs functionality, allowing you to enjoy consistent heating results every time. Crafted from high-quality materials, this thermostat offers durability and dependable operation, giving you peace of mind with your repair. Whether your original thermostat is malfunctioning or needs replacement, the Microwave Thermostat is the perfect solution to maintain your microwaveGÇÖs efficiency and reliability. Trust in this genuine OEM part to keep your Samsung microwave running smoothly and effectively.

Fix an oven that overheats or won't heat properly. This high-limit thermostat monitors temperature and shuts off power if the cavity gets too hot.

Fix an oven that overheats or shuts off unexpectedly with this high limit thermostat. Safety cutoff prevents damage. DIY-friendly replacement part.

This SPDT high-amp switch controls high-current circuits by switching one input between two outputs, restoring proper electrical control in affected appliance functions. Built for high-load switching where reliable on/off selection is required. What it does:

• Directs high-current power from a single input to one of two outputs (single-pole, double-throw action)
• Replaces worn or failed selector/limit-style switches that cause intermittent or no power to a circuit
• Commonly used where a high-amp, durable switching contact is required to complete a function
• Helps stop symptoms like intermittent operation, failure to switch between states, or no power to the controlled circuit

• One SPDT high-amp switch (WB24T10160)

• Disconnect power to the appliance before inspecting or replacing the switch
• Verify wiring locations and take a photo before removal for correct reconnection
• Use proper tools and avoid touching energized contacts;

Oven won't heat after self-clean? This thermal fuse protects your oven from overheating. Replacement takes about 1 hour with basic tools. Video guide included.

Replacement thermostat that senses and controls the appliance heating system to restore accurate heating and stable temperature cycles, helping the appliance reach and maintain the set temperature. What it does:

• Senses temperature and signals the heating element or valve to turn on/off to maintain set temperature.
• Commonly linked to symptoms such as failure to reach set temperature, temperature fluctuating or cycling erratically, or continuous heating.
• Works as the temperature-regulation component in the appliance's control pathway to stabilize performance.
• Matches the OEM function for temperature control; use when thermostat diagnostics indicate a failed or inaccurate sensor.

• Disconnect power to the appliance before attempting removal or installation to avoid shock or ignition hazards.
• Handle the sensing element and terminals carefully to avoid damage; ensure secure electrical connections and proper routing of any capillary or sensor lead.
• After installation, test the appliance through a full heat cycle to confirm correct operation.

This limit switch is a position-sensing safety switch used in cooking appliances. It signals the control when a mechanism reaches the correct position, helping the unit start or stop related functions reliably.

• Detects the position of a latch, cam, or actuator and opens/closes the circuit accordingly
• Allows the control to enable features only when the correct position is reached
• Common symptoms: related feature won't start or finish, motor runs but never "signals done," intermittent operation, or no continuity change when the switch is actuated
• Restores dependable interlock/position feedback to the control

• Disconnect power at the breaker before servicing
• Access point varies by model; the switch is typically mounted near the associated mechanism it monitors
• Move wires over one at a time and note terminal orientation to match the original setup
• The actuator is aligned and the switch clicks/changes continuity when pressed; test operation before reassembly