Range Fuse Or Sensor

This SPDT high-amp switch controls high-current circuits by switching one input between two outputs, restoring proper electrical control in affected appliance functions. Built for high-load switching where reliable on/off selection is required. What it does:

• Directs high-current power from a single input to one of two outputs (single-pole, double-throw action)
• Replaces worn or failed selector/limit-style switches that cause intermittent or no power to a circuit
• Commonly used where a high-amp, durable switching contact is required to complete a function
• Helps stop symptoms like intermittent operation, failure to switch between states, or no power to the controlled circuit

• One SPDT high-amp switch (WB24T10160)

• Disconnect power to the appliance before inspecting or replacing the switch
• Verify wiring locations and take a photo before removal for correct reconnection
• Use proper tools and avoid touching energized contacts;

This limit switch is a position-sensing safety switch used in cooking appliances. It signals the control when a mechanism reaches the correct position, helping the unit start or stop related functions reliably.

• Detects the position of a latch, cam, or actuator and opens/closes the circuit accordingly
• Allows the control to enable features only when the correct position is reached
• Common symptoms: related feature won't start or finish, motor runs but never "signals done," intermittent operation, or no continuity change when the switch is actuated
• Restores dependable interlock/position feedback to the control

• Disconnect power at the breaker before servicing
• Access point varies by model; the switch is typically mounted near the associated mechanism it monitors
• Move wires over one at a time and note terminal orientation to match the original setup
• The actuator is aligned and the switch clicks/changes continuity when pressed; test operation before reassembly

This push-button replacement switch restores reliable user control for compatible Frigidaire appliances. It replaces a worn or failed control switch so buttons respond correctly and features return to normal operation. What it does:

• Completes the electrical circuit when pressed to send the user command to the appliance control
• Helps fix symptoms such as unresponsive or intermittent button operation
• Prevents unintended cycling or failure to start when the original switch has worn contacts
• Works as the user-interface switching component for the affected control panel or assembly

• One replacement push-button switch

• Disconnect power to the appliance before attempting service to avoid electrical shock
• Access may require removing the control panel or trim; keep fasteners organized for reassembly
• Verify panel orientation and wire connector positions before removing the old switch

A hi-limit safety switch that stops heating when temperatures get too high, protecting the appliance from overheating and helping prevent damage. Designed to replace a failed thermal cutoff to restore safe temperature control. What it does:

• Opens the heating circuit when internal temperature exceeds the safe limit to prevent overheating
• Commonly replaces a failed or intermittently opening thermal limit control
• Helps stop burners or heating elements from running unchecked when a thermostat fails
• Addresses symptoms like no heat, intermittent heating, or safety trip shutdowns

• Disconnect power before accessing heating components and wiring
• Verify the part matches the appliance diagram and wiring orientation before installation
• If corrosion or other damage is present on connectors or terminals, replace or repair per OEM guidance

This thermostat temperature limiter helps stop heating when temperatures exceed safe levels, protecting the appliance and preventing overheating. It fits specific Whirlpool systems and restores proper temperature control when the limiter has failed. What it does

• Acts as a safety cutoff to interrupt heating when internal temperatures get too high.
• Prevents the appliance from continuing to heat during an over-temperature condition.
• Common symptom: appliance runs but produces little or no heat.
• Common symptom: heating cycles off prematurely or intermittently.

• One thermostat temperature limiter.

• Disconnect power (unplug or shut off breaker) before accessing the appliance.
• Handle and route wiring carefully; replace only with the exact OEM part number.
• Test circuits with a multimeter to confirm thermostat failure before replacing.

This temperature control thermostat replaces the refrigerator's manual/mechanical control that cycles the compressor and fans to maintain set temperatures, helping restore consistent cooling. Simple, direct replacement for units using this style of controller. What it does:

• Opens and closes the cooling circuit based on the temperature setting to regulate cabinet temperature
• Stops continuous running when the compressor fails to cycle or restarts cooling when the temperature rises
• Commonly used when the refrigerator won't reach or hold set temperatures or runs constantly
• Compatible with systems that use a mechanical dial-style temperature control and capillary sensing tube

• Disconnect power before servicing to avoid shock or injury
• Replace the thermostat in the same orientation and secure sensing tube without kinks; handle the capillary tube carefully
• Verify electrical connections match the original and restore power only after mounting is complete
• If temperature issues persist after replacement, check related components (evaporator, defrost, compressor)

This bimetal limit thermostat is a safety temperature cutoff that stops heat when an oven or range overheats, helping protect the appliance and prevent further damage. It replaces a failed thermal cutoff that won't reset or maintain safe temperatures. What it does:

• Opens the circuit to the oven heating system when internal temperature exceeds safe limits
• Helps prevent overheating and reduces risk of heat-related component failure
• Common symptom: oven heats inconsistently or will not come up to temperature
• Common symptom: oven elements or burners remain off after an overheat event

• Disconnect power to the appliance before servicing to avoid electrical shock.
• Access typically requires removing the oven back panel or control housing; follow OEM service instructions.
• Replace only with the exact part number; do not attempt to modify or bend the thermostat.

This 15 amp, 250 volt replacement fuse protects your appliance's electrical circuits by interrupting power when a fault or overload occurs. It restores safe operation once the underlying issue is fixed and the fuse is replaced. What it does:

• Acts as an overcurrent protection device for circuits rated up to 15 A and 250 V
• Prevents damage to wiring and components by opening the circuit during an overload or short
• Common symptom: appliance has no power or specific functions stop working after a sudden failure
• Replacing a blown fuse can resolve intermittent power loss or complete power failure tied to a single blown element

• Disconnect power to the appliance before inspecting or replacing the fuse
• Replace only with a fuse of the same amperage and voltage rating to maintain safety and proper protection
• Use insulated tools and avoid touching live terminals; internal access may require disassembly, follow OEM service instructions
• If fuses blow repeatedly, stop using the appliance.

This hi-limit thermostat is a temperature-sensing safety switch that stops power to the heating circuit if temperatures rise above safe levels, helping protect the appliance from overheating and heat-related damage. What it does:

• Senses excessive temperature and interrupts power to the heating element
• Helps prevent continuous heating and potential overheating hazards
• Can cause the appliance to lose heat or fail to maintain temperature when it trips or fails
• Common symptom: no heat or intermittent heating when the limiter is open

• Disconnect power to the appliance before inspecting or replacing the limiter
• Locate and replace only the thermostat explicitly matching the appliance's wiring and mounting
• Verify wiring terminals match and are secure; do not modify terminals or leads

This fixed thermostat monitors and limits temperature to protect the appliance's system and components. It's a simple, non-adjustable sensor/limit switch used where a set cutoff temperature is required for safe operation. What it does:

• Opens or cuts power when the monitored temperature reaches its fixed limit to prevent overheating
• Helps stop continuous heating cycles caused by a failed control or sensor
• Commonly used as a safety cutoff in temperature-control circuits
• Can resolve symptoms like persistent overheating, failure to stop heating, or temperature-related shutdowns

• One fixed thermostat (single unit)

• Disconnect power before inspecting or replacing the thermostat to avoid shock or damage
• Handle gently; avoid bending terminals or stressing sensing elements

This high-limit thermostat is a temperature safety switch that helps prevent overheating by opening the circuit when temperatures exceed safe limits. It restores normal operation once the temperature cools, protecting the appliance and reducing fire risk. What it does:

• Monitors internal temperature and opens the circuit if heat gets too high
• Prevents overheating that can cause damage or burn odors
• Commonly replaces a failed or intermittently tripping thermal safety switch
• Works as part of the appliance's temperature-safety system, not a primary temperature control

• Disconnect power to the appliance before attempting replacement
• Observe proper wiring orientation and secure terminal connections
• Replace only with the exact part specified for your appliance