Range Fuse Or Sensor

This thermal cutoff (runaway) is a temperature-safety device that stops the dryer's heating circuit if temperatures exceed safe limits, helping prevent overheating and potential fire hazards. Replaces a failed or tripped runaway TCO in dryer heating assemblies. What it does:

• Opens the heating circuit if the dryer temperature climbs above safe thresholds to stop further heating.
• Prevents uncontrolled heating when other thermostats or controls fail.
• Common symptom: dryer overheats or element stays energized; may also result in no heat if the cutoff is open.
• Works with the dryer's existing thermostats and heating element assembly as a safety interlock.

• One thermal cutoff (runaway) device.

• Disconnect all power before accessing the dryer heating assembly.
• Locate and replace the TCO on or near the heater housing; keep wiring orientation the same.
• Do not bypass or defeat safety devices; After replacement, inspect other thermostats, fuses, and the heating element for related faults.

This time delay fuse protects the appliance from overheating by opening the circuit when temperatures exceed safe limits. It's a direct-replacement electrical safety fuse used in heating circuits to help prevent damage and fire risk. What it does:

• Opens the circuit when the detected temperature rises above safe operating limits to stop the heating element
• Helps prevent overheating-related damage to internal components and wiring
• Can cause intermittent or no heating when failed
• Commonly associated with symptoms such as no heat, reduced or inconsistent heating, or a unit that stops running during heating cycles

• Disconnect power to the appliance before accessing or replacing the fuse to avoid electrical shock
• Locate the fuse according to your appliance's service manual or diagram and replace with the exact part number
• If the fuse is blown, inspect heating element, thermostat/thermal cutouts, and venting for underlying faults before reinstalling

This bimetal limit thermostat is a safety cutoff that helps prevent ovens and ranges from overheating. It replaces a failed temperature limit control to restore proper high-temperature protection and safe operation. What it does:

• Acts as a high-limit cutoff to stop heat if the appliance exceeds safe temperatures
• Prevents excessive heating that can cause burnout or unsafe operation
• Can cause an oven or burner to stop heating or fail to reach temperature when it has failed
• Supports normal cycling of the appliance by sensing and responding to over-temperature conditions

• One bimetal limit thermostat

• Disconnect power to the appliance before inspecting or replacing this part
• Replace with the exact part number shown on the old thermostat to ensure proper fit
• Handle with care; avoid bending the sensing element or terminals

This high-limit thermostat (hi-limit switch) is a temperature safety device that stops the heating circuit if the appliance overheats, helping protect the unit and restore proper heat control when replaced. What it does:

• Opens the heating circuit if internal temperature exceeds safe limits to prevent overheating.
• Controls whether the heater/element receives power based on temperature.
• When faulty, common symptoms include no heat or intermittent heating and repeated thermal cutouts.
• Can be tested for continuity to confirm electrical function.

• One high-limit thermostat (hi-limit switch).

• Disconnect power before inspecting or replacing; risk of shock or injury if energized.
• Note and label wire locations or take a photo before removal for correct reassembly.
• Verify part compatibility with your model before installing; confirm continuity after installation.

A limit switch that stops power when temperatures exceed safe levels, preventing overheating and protecting the appliance and its controls. Installs at the heat source to help maintain safe operation and reliable performance. What it does:

• Acts as a temperature-activated safety cutoff to interrupt power when temps climb too high
• Can prevent continuous heating and protect control components from heat damage
• A failed switch may cause intermittent operation, no heat to the element, or a complete shutdown
• Works as a protective device in heating circuits and safety interlocks

• Disconnect power to the appliance before servicing to avoid shock or burns
• Verify correct part placement and wire connections; note terminal locations before removal
• Test continuity with a multimeter to confirm failure before replacing

This door push-button light switch controls the interior lamp by turning it on when the refrigerator door opens and off when the door closes. It replaces a worn or failed push-button actuator to restore reliable light operation. What it does:

• Completes the circuit to the interior light when the door opens and breaks the circuit when closed
• Commonly causes no interior light, intermittent lighting, or lights that stay on
• Fits in the refrigerator door frame and interfaces with the existing wiring harness
• Simple, single-function electromechanical switch—no electronics to program

• One door push-button light switch

• Disconnect power to the appliance before servicing to avoid shock
• Remove the door trim or bezel as needed to access the switch (requires basic hand tools)
• Handle the switch and wiring gently; do not force connectors or overtighten fasteners

This thermal fuse stops excessive heat build-up by opening the circuit when temperatures get unsafe, protecting the appliance and its heating components. Replace a failed fuse to restore normal heating and safety functions. What it does

• Opens the circuit if overheating is detected to prevent damage or fire risk.
• Prevents the heating element or motor from running when the fuse is blown.
• Common symptom: appliance fails to heat or runs but produces no heat.
• Common symptom: appliance does not start or suddenly stops during a heat cycle.

• One thermal fuse.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Replace with the exact OEM part number; improper substitutes may cause malfunction or safety issues.
• Inspect surrounding wiring and heating components for faults that could cause repeated fuse failures.

This safety thermostat helps prevent overheating by cutting power when temperatures get too high. It's a direct-replacement safety control used in heating circuits to protect the appliance and reduce fire risk. What it does:

• Opens the circuit when internal temperatures exceed safe limits to stop heating
• Prevents overheating of components and wiring
• Helps stop recurring high-heat faults that can damage the appliance
• Used as a fail-safe backup to the main temperature control

• One safety thermostat

• Disconnect power to the appliance before servicing to avoid electrical shock
• Replace only with the exact part number to maintain safety function
• Handle terminals carefully; ensure secure electrical connections and proper mounting