Range Valve

This mini burner valve controls gas flow to an individual cooktop/range burner, restoring proper ignition and flame control for affected burners. Designed as a direct-replacement service part for compatible gas ranges. What it does:

• Regulates gas flow to a single burner so the burner can light and hold a steady flame
• Commonly replaces valves that leak, stick, or fail to modulate flame size
• Used when a burner won't ignite, has uneven flame, or cannot be adjusted properly
• Works with the cooktop's ignition and safety systems to deliver controlled fuel to the burner

• One burner valve (mini)

• Turn off the gas supply and unplug the appliance before starting any work
• Use appropriate tools and replace any gaskets or fittings as needed; do not overtighten
• If you smell gas, stop work immediately, ventilate the area.

This solenoid valve is the electrical valve assembly that opens and closes to control fluid flow in the appliance, restoring proper fill and shutoff behavior when the original valve fails. What it does:

• Electrically opens and closes to allow or stop fluid flow to the appliance
• Stops unintended flowing or leaking when the valve seals properly
• Commonly linked to symptoms such as no fill, continuous filling, intermittent fill, or leaks near the valve
• Works as the actuator controlled by the appliance's control board to meter fluid delivery

• Disconnect power and shut off the water supply before servicing.
• Handle valve connections and seals carefully; replace any damaged gaskets or hoses.
• Reconnect wiring to the correct terminals and secure all fittings to avoid leaks.
• Test appliance through a full cycle after install and check for leaks.

This burner valve controls the gas flow to a single surface burner, restoring reliable ignition and consistent flame control for gas ranges. It's a direct-fit replacement when the existing valve fails. What it does

• Regulates gas delivery to one surface burner so the burner lights and holds a steady flame
• Commonly replaces valves that cause weak or no flame at a burner
• Helps stop erratic flame behavior caused by faulty gas regulation
• Works with the range's control knob to adjust flame size safely

• One burner valve

• Turn off the gas supply and electrical power before starting work
• Verify the fit and orientation before final installation; some disassembly of the cooktop or manifold may be required
• Use proper gas fittings and check all connections for leaks with a soapy-water test after installation

The Valve Control Assembly is an OEM part for GE gas ranges. It regulates the flow of gas to burners via integrated solenoid valves, ensuring safe ignition and temperature control during cooking cycles. 

Causes of a bad Valve Control Assembly can include:

• Mineral or debris buildup affecting gas flow
• Overheating warping critical valve housing parts
• Worn solenoid valves inhibiting proper opening/closing

Symptoms include:

• Uneven or inconsistent burner flame levels
• Difficulty maintaining selected temperature settings
• Burner ignition issues requiring service calls
• Potential gas leaks from faulty valve sealing integrity

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.
 

This water inlet valve controls water flow to the refrigerator's ice maker and water dispenser, restoring normal dispensing and ice production when the valve is faulty or leaking. What it does

• Opens and closes to allow water into the ice maker and dispenser as commanded by the refrigerator.
• Stops water flow to prevent overfilling; a failed valve can cause no water, slow flow, or continuous filling.
• Commonly linked to symptoms such as no ice production, weak or no water from the dispenser, or visible leaks at the valve.

• One water inlet valve assembly.

• Disconnect power and shut off the water supply before starting work.
• Relieve line pressure and have towels ready for residual water when disconnecting fittings.
• Inspect and replace any worn water line fittings or gaskets; tighten connections to manufacturer torque—do not overtighten plastic fittings.

This top-burner gas valve controls gas flow to a single surface burner, restoring proper heat adjustment and safe burner operation. It's a direct-replacement style part used on compatible ranges and cooktops. What it does:

• Regulates gas flow to a single top/surface burner so you can adjust flame intensity
• Enables ignition and consistent burner flame when operating normally
• Commonly replaces valves when a burner won't light, has no gas flow, or will not hold a steady flame
• Helps restore safe, controllable heating when the original valve is faulty

• One (1) top burner gas valve

• Turn off gas supply and disconnect power before starting work
• Inspect seals and fittings for leaks after installation; use a leak-detection solution or follow OEM leak-check procedures
• Follow OEM service instructions and local codes for safe installation

This top burner valve controls gas flow to a single cooktop burner so you can adjust heat and restore proper burner operation. It replaces a worn or failed valve to help burners light and hold a steady flame. What it does:

• Regulates gas flow from the manifold to one surface burner for precise heat control.
• Replaces valves that are stuck, hard to turn, or fail to deliver consistent flame.
• Helps resolve symptoms like a burner that won't light, weak or uneven flame, or loss of ignition control.
• Works as a direct replacement when the original valve is damaged or leaking.

• One top burner gas valve.

• Turn off gas supply and electrical power to the appliance before starting work.
• Only install on compatible gas ranges; follow OEM instructions and local codes.
• Use proper fittings and sealants rated for gas; check all connections for leaks after installation.

This burner valve controls gas flow to a single surface burner, restoring proper heat output and reliable ignition when the valve is functioning. It's the direct replacement part that lets a burner reach its correct flame level. What it does:

• Regulates gas flow to one cooktop burner so the flame responds to knob position
• Enables steady ignition and consistent heat for normal cooking
• Common symptoms it addresses: burner won't light, flame is weak or won't stay lit, or burner only works on certain knob settings
• Designed to match OEM fit and function for straightforward replacement

• Turn off gas supply and electrical power before starting any work
• Use appropriate hand tools; avoid forcing fittings or connections
• After installation, check all gas connections for leaks with a soap solution or approved leak detector

This gas valve controls fuel flow to the range/oven burner, restoring reliable ignition and heat control. Precision operation helps maintain even cooking and safe burner performance when the valve is faulty. What it does:

• Regulates gas flow to the burner assembly so the oven/range heats correctly
• Works with the appliance's safety and ignition systems to enable reliable lighting
• Commonly replaced for symptoms like no heat, intermittent ignition, or gas smell during operation
• Designed as a direct-fit valve for compatible Whirlpool-built ranges using Copreci 16k valves

• Turn off gas supply and disconnect power before attempting service
• Follow the appliance service manual for proper valve removal and gas line reconnection
• Check all fittings for leaks after installation and before returning the appliance to service