Refrigerator Blower Wheel Or Fan Blade

This replacement fan circulates air through the appliance to maintain proper airflow and stable temperatures. Installing a new fan restores efficient performance and can reduce noise, vibration, and uneven airflow or cooling. What it does:

• Circulates air to support proper airflow and temperature control
• Helps cool internal components and distribute air evenly
• Common symptoms include the fan not spinning, intermittent operation, loud or rubbing noises, excessive vibration, or weak airflow
• Visible wear or damage to the fan vanes or hub can indicate the need for replacement

• One fan, as shown

• Disconnect power before servicing; allow moving parts to stop completely
• Access the fan location and note the original orientation for correct airflow
• Transfer any clips, spacers, or fasteners from the original part as needed
• After installation, hand-spin to ensure free movement and clearance; restore power and test for smooth operation

This evaporator fan blade mounts on the freezer fan motor to move air across the evaporator coils and circulate cold air through the cabinet, helping maintain proper temperatures when the original blade is cracked, warped, or missing.

• Circulates air over the evaporator coils for efficient heat removal and even cooling
• Helps restore airflow between freezer and fresh food sections
• Addresses symptoms such as weak/no airflow from vents, rising temperatures, or rattling/scraping noises from the freezer area
• Replaces a damaged blade that wobbles or rubs the shroud

• Disconnect power; remove freezer shelves/bins and the rear panel to access the fan assembly
• Pull the old blade straight off the motor shaft; avoid prying on or bending the shaft
• Match the orientation of the original and press the new blade onto the shaft until fully seated with clearance to the shroud
• Spin by hand to ensure free movement; reassemble panels and restore power

An evaporator fan blade mounts on the evaporator fan motor to move cold air across the coils and throughout the refrigerator compartments. Replacing a cracked, warped, or loose blade restores proper airflow, temperature balance, and quiet operation.

• Circulates air across the evaporator and into the fresh food and freezer sections to maintain even temperatures
• Helps reduce frost/ice buildup on the evaporator cover by improving airflow after defrost
• Common symptoms of a damaged blade: rattling or scraping noises behind an interior panel, weak or no airflow at vents, warming in the fresh food section, or uneven cooling
• A cracked or loose blade may spin but move little air even when the motor runs

• Disconnect power to the refrigerator before service
• Access the evaporator fan behind the interior rear panel; remove the cover/shroud as required (varies by model)
• Note blade orientation; seat the new blade fully on the motor shaft and verify clearance inside the shroud
• Reassemble panels, restore power, and confirm the fan spins freely without rubbing

This condenser fan assembly circulates air across the condenser coils and compressor to remove heat from the refrigeration system. Replacing a failing fan helps restore efficient cooling performance and protects the compressor from overheating. What it does:

• Draws air through the condenser coils to dissipate heat
• Supports proper system pressures and overall cooling efficiency
• Helps maintain stable temperatures in both compartments
• Common symptoms include the fan not running, loud noise from the rear, warm cabinet temperatures, or a very hot compressor area

• Pre-assembled fan motor with blade and mounting bracket

• Disconnect power before servicing; use gloves to protect against sharp edges
• Access the lower rear compartment and remove the back cover to reach the fan
• Note wire positions; move over any reusable grommets or screws and secure the assembly firmly
• The blade spins freely and is oriented to move air across the condenser; clean coils before restoring power

Refrigerator Fan Blade is a crucial component for ensuring your Samsung refrigerator operates efficiently. This genuine OEM part is designed to maintain optimal airflow within your appliance, promoting consistent cooling and preventing temperature fluctuations. By replacing a worn or damaged fan blade with this high-quality part, you can restore your fridgeGÇÖs performance, keeping your food fresh and extending the lifespan of your refrigerator. The fan blade is crafted with precision to ensure a perfect fit for a variety of Samsung refrigerator models, making installation straightforward and hassle-free. Its durable construction resists wear and tear, providing reliable performance even in demanding environments. Additionally, a properly functioning fan helps reduce energy consumption by allowing your refrigerator to run more smoothly. Whether youGÇÖre experiencing unusual noises, inadequate cooling, or need to replace a broken fan blade, the Refrigerator Fan Blade offers a dependable solution. Trust in this genuine OEM part to deliver the quality and performance you expect from your Samsung appliance, enhancing your overall kitchen experience.

The Bottom-Mount Refrigerator Fan Propeller is essential for maintaining optimal airflow in your Samsung bottom-mount refrigerator. This genuine OEM part ensures consistent temperature distribution, helping to keep your food fresh and your appliance running efficiently. Crafted with precision, the fan propeller operates smoothly and quietly, reducing energy consumption and preventing overheating. The Bottom-Mount Refrigerator Fan Propeller is specifically designed to fit a range of Samsung bottom-mount refrigerator models, guaranteeing a secure and seamless installation. Replacing a worn or damaged fan propeller with this high-quality part restores your refrigerator's performance, enhancing its longevity and reliability. Trust in this genuine OEM part to provide the functional benefits you need for a well-performing and dependable refrigerator.

This replacement fan blade mounts on the fan motor to move air for proper cooling. A cracked, loose, or damaged blade can cause noise and weak airflow—replacing it restores smooth, reliable air circulation. What it does:

• Drives airflow to help maintain stable temperatures throughout the appliance
• Supports efficient cooling by circulating air across key areas
• Common symptoms include rattling or scraping near the fan, vibration, or wobbling
• Replacement is recommended if the motor runs but the blade slips, doesn't spin, or is visibly damaged

• 1 fan blade

• Disconnect power before servicing
• Access the fan area by removing covers/shelves as needed
• Note blade orientation; pull the old blade straight off the shaft and press the new blade on until fully seated
• Spin the blade by hand to confirm clearances, reassemble, and restore power

This is the evaporator fan assembly that circulates cold air throughout the freezer and refrigerator sections for even cooling. Replacing a failed assembly restores proper airflow and temperature consistency.

• Draws air across the evaporator coils and distributes it through the cabinet
• Helps maintain stable, uniform temperatures and prevents warm spots
• Common failure symptoms: buzzing or grinding from the freezer, weak/no airflow, warming in fresh food section, frost buildup around the evaporator cover
• Fits in the freezer compartment behind the rear interior panel

• Disconnect power before servicing; sharp edges may be present behind the panel
• Remove shelves and rear freezer panel to access the assembly
• Transfer any grommets/insulators in the same orientation if reused
• After installation, verify fan operation and ensure no wires contact the blade

This condenser fan blade mounts to the fan motor and pulls air across the condenser coil and compressor. Replacing a cracked or warped blade restores airflow so your refrigerator cools efficiently and the compressor runs at a safe temperature.

• Circulates air through the condenser coil and over the compressor to remove heat
• Helps maintain cooling performance and stable system pressures
• Common symptoms: weak or no airflow at the rear/base, rattling or scraping noises, wobble/vibration, visible cracks or missing fins, warmer-than-normal compartments or hot cabinet sides
• Works with the condenser fan motor and shroud; typically replaced when the hub is stripped or the blade is damaged

• Disconnect power and pull the refrigerator out; remove the rear access cover near the compressor
• Note blade orientation and depth on the motor shaft before removal
• Pull the old blade straight off; press the new blade onto the shaft until fully seated and ensure it spins freely with proper shroud clearance
• Reinstall the cover, restore power, and verify strong, quiet airflow

The Refrigerator Fan Blade is designed to maintain optimal airflow within your Samsung refrigerator. Crafted as a genuine OEM part, this fan blade ensures reliable performance and a perfect fit for your appliance. Made from durable materials, it withstands constant use and helps to keep your fridge consistently cool. By facilitating efficient air circulation, the Refrigerator Fan Blade helps maintain the ideal temperature, preserving your food longer and reducing energy consumption. Its precise engineering minimizes noise and vibration, enhancing the overall quiet operation of your refrigerator. Easy to install, this fan blade seamlessly integrates with your existing refrigerator system, restoring its functionality without hassle. Compatible with a wide range of Samsung refrigerator models, it is the perfect replacement part for any damaged or worn fan blades. Investing in this genuine OEM part guarantees the longevity and efficiency of your refrigerator, providing you with peace of mind and a better cooling experience. Ensure your Samsung refrigerator operates at its best with the reliable performance of the Refrigerator Fan Blade .

This evaporator fan blade mounts on the freezer fan motor and circulates air across the evaporator coils. Replacing a cracked or warped blade restores proper airflow for even cooling and more consistent temperatures throughout the refrigerator.

• Moves chilled air from the evaporator through the ducts to both compartments
• Helps maintain uniform temperatures and overall cooling performance
• Common symptoms of a faulty blade: weak airflow, poor cooling or warm spots, rattling/scraping noises from the freezer, longer run times
• Visual signs include a cracked hub, loose fit on the shaft, or broken/missing vanes

• Disconnect power before servicing
• Remove freezer shelves/ice bin and the rear panel to access the fan assembly
• Pull the old blade straight off the motor shaft; align the hub and press the new blade on until fully seated
• Verify blade orientation and free rotation inside the shroud before reassembly

The Evaporator Fan Blade is an OEM component specifically designed for Frigidaire brand refrigerators. This fan blade is located within the evaporator coil assembly and works to circulate cold air throughout the refrigerator compartment. 

Symptoms of a bad fan blade include: 

• Excessive heat buildup inside refrigerator sections
• Inability to sufficiently cool foods or maintain temperatures  
• Vibration or grinding noises emanating from rear wall
• Complete lack of air circulation felt at vents

Causes for replacement include wear and tear of plastic components over many years of constant spinning motion, cracks, or breakage from foreign object interference.

This genuine OEM Frigidaire part is also compatible with some Kelvinator and Admiral models.

Replacement fan blade that moves air across the evaporator and through the cabinet to help maintain even temperatures. Restores proper airflow and reduces noise and vibration caused by cracked, bent, or worn blades. What it does:

• Circulates cold air from the evaporator throughout the refrigerator/freezer compartments
• Helps maintain consistent temperatures and reduce hot spots
• Reduces noise and vibration when replacing damaged or unbalanced blades
• Works with the evaporator/air-movement motor to support normal defrost and cooling cycles

• Disconnect power before accessing the evaporator/fan area to avoid electric shock.
• Remove shelves, panels, and the evaporator cover as needed to reach the fan assembly.
• Handle the blade carefully — edges and nearby sheet metal can be sharp.
• Inspect the fan motor shaft and mounting hardware; replace any worn or damaged components for best results.

This replacement fan blade mounts to the fan motor to move air through the system, restoring proper airflow and helping maintain stable temperatures while reducing unwanted noise and vibration. What it does:

• Attaches to the fan motor shaft to circulate air through the appliance
• Drives airflow across coils and compartments to support proper cooling
• Helps maintain even temperatures and stable performance
• Common symptoms include rattling/whirring noises, weak airflow, warm spots, or wobbling due to a cracked or warped blade

• Disconnect power before servicing
• Access the fan housing; remove any guards/shrouds as needed
• Transfer and reuse the existing retainer/clip or fastener and fully seat the blade on the motor shaft with correct orientation
• Spin by hand to ensure free clearance; reassemble and test for smooth, quiet operation

The Fan Blade is an OEM part for Whirlpool refrigerators. It helps cool down the condenser coils by drawing air over them, providing cooling and temperature regulation inside the refrigerator.

A bad fan blade can be caused by wear and tear, damage from debris or foreign objects, or motor malfunctions. If you notice issues such as poor cooling performance, unusual noises coming from the refrigerator, or the fan not spinning properly, it may indicate a problem with the fan blade.

Symptoms of a bad fan blade include:

• Inadequate cooling or temperature fluctuations 
• Unusual noises coming from the refrigerator
• The fan not spinning or spinning slowly

Replace your faulty fan blade with this genuine OEM part to restore your refrigerator. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

Instruction sheet included.