Refrigerator Touch Pad

Fix a dispenser that won't shut off or won't respond when you press the lever. This control module reads paddle inputs and coordinates ice/water flow.

Dispenser cover broken or cracked? This protective trim snaps into place over dispenser components. Simple DIY repair—tabs pop off with gentle prying.

Fix unresponsive water or ice buttons, stuck dispenser, or blank display. This control board processes touchpad inputs. Easy 10-minute DIY repair.

Replace worn or faded dispenser control labels that make settings hard to read. This overlay restores clear ice/water markings. Simple peel-and-stick fix.

Fix a blank or unresponsive ice and water dispenser display. This touchpad interface assembly restores control panel function. Moderate DIY repair.

Fix dispenser lights not working or unresponsive touch controls. This glass touch dispenser assembly restores water and ice dispensing on your refrigerator.

This dispenser cover assembly replaces a cracked or damaged dispenser housing cover to restore a clean appearance and help the dispenser direct ice and water properly. Molded plastic protects internal components and maintains dispenser alignment. What it does:

• Covers and protects the dispenser opening and internal components from dirt, moisture, and impact.
• Helps guide ice and water to reduce jams, misfeeds, and drips at the dispenser opening.
• Restores appearance when the original cover is cracked, split, or cosmetically damaged.
• Seats into the dispenser housing using factory clips and mounts to maintain proper alignment.

• Disconnect power and shut off the water supply before servicing to prevent shock and leaks.
• Remove dispenser trim or inner door panel to access the cover; support the door/trim while working.
• Handle plastic clips and tabs carefully—damaged clips may require replacement.
• After installation, restore power/water and test the dispenser for proper function and leaks.

Fix unresponsive ice or water dispenser buttons with this control panel. Snaps into place on the dispenser assembly. Moderate DIY difficulty.

Ice and water dispenser buttons not working? This control panel restores touchpad function. Common DIY fix when buttons are unresponsive or stuck on one mode.

This is the touchpad membrane switch used on the refrigerator's dispenser control panel. It registers button presses for selecting water, ice, or other dispenser functions. Replace this part if the dispenser buttons are unresponsive, require excessive pressure, or activate the wrong function when pressed.

This dispenser cover assembly restores a clean, secure front to the refrigerator's ice/water dispenser area. It protects internal components and provides the finished bezel for the user interface on the freezer door.

• Covers and protects the dispenser compartment and wiring
• Provides the front bezel for dispenser selections and indicators
• Helps keep internal components aligned and securely mounted
• Common symptoms: cracked or missing bezel, broken tabs, loose/rattling panel, worn appearance

• Disconnect power before servicing
• Remove the drip tray and any retaining screws/clips; carefully release the old cover
• Transfer existing controls/electronics and hardware to the new cover
• Reinstall cover and fasteners; restore power and test dispenser functions

Dispenser facade cracked or discolored? This trim assembly restores your refrigerator's dispenser appearance and proper fit. Straightforward install.

Dispenser not working or unresponsive? This control assembly operates water and ice dispensing functions. Direct replacement for failed touchpad controls.

This separator is a molded plastic divider that helps keep ice organized inside the ice bin for smoother dispensing and less clumping. It restores proper spacing so ice moves freely during dispense cycles. What it does:

• Divides and guides ice inside the ice bin to reduce jamming and clumping
• Helps improve ice feed into the auger or dispenser chute
• Reduces shifting and rattling of ice during door movement
• Restores intended bin geometry after a cracked or missing divider

• One separator

• Unplug the refrigerator or shut off power before working on the ice bin or dispenser
• Empty the ice bin and remove any loose ice to avoid spills during replacement
• Snap the separator into the molded slots in the ice bin; no tools typically required

Fix a cracked or faded dispenser front panel with this exterior trim bezel. Restores a finished look around your ice and water dispenser controls.