Refrigerator Ice Door Or Ice Chute

This funnel directs water into the ice maker fill cup to ensure proper filling and reduce spills. It helps maintain reliable ice production by guiding water flow to the correct inlet area. What it does:

• Directs incoming water into the ice maker's fill cup so the correct amount reaches the ice mold
• Reduces splashing and overflow during the fill cycle
• Helps prevent water from pooling inside the freezer compartment near the ice maker
• Supports consistent ice production when installed and aligned properly

• Disconnect power to the appliance before servicing to avoid electrical shock
• Remove the ice maker or access panel as needed to reach the old funnel
• Align the replacement funnel with the mounting tabs and secure per OEM orientation; avoid forcing it into place
• Test fill cycle after installation and check for leaks; for detailed steps

A protective housing cover that shields internal components and restores the appliance's finished appearance. Replaces a cracked, broken, or missing cover to help keep wiring and controls protected from dirt and accidental contact. What it does

• Covers and protects internal wiring, connectors, and control components from debris and accidental contact
• Restores the appliance's exterior appearance when the original cover is damaged or missing
• Helps prevent moisture and small objects from entering the component area
• Reduces risk of further damage to underlying parts caused by impact or wear

• Disconnect power to the appliance before attempting any repair.
• Handle edges carefully; some covers have sharp edges or fragile tabs.
• May require removal of nearby trim or screws for access; keep fasteners organized.

This plug seals an unused hole in an appliance cabinet or inner liner to help block drafts, pests and moisture. It restores a clean, finished appearance and prevents accidental debris entry where a fitting or fastener is not used. What it does:

• Seals unused openings in the appliance cabinet or liner to keep out dust, moisture and pests
• Helps prevent air leaks that can affect temperature stability in refrigerators and freezers
• Covers exposed holes left after removing or relocating components or fasteners
• Restores a finished look to access areas and reduces risk of small-item ingress

• One cabinet sealing plug

• Push the plug into the hole until fully seated; no special tools usually required
• Turn off and unplug the appliance before reaching into compartments or behind panels
• Inspect the hole and plug for correct fit; replace if cracked or deformed

This ice guide directs ice from the ice maker into the storage bin to help prevent spills and misfeeds. It replaces a cracked, worn or misaligned guide so ice drops cleanly into the bin. What it does:

• Guides ice cubes from the dispenser/ice maker outlet into the ice bin to reduce jams and spillage
• Helps keep cubes aligned for smooth dispensing and bin storage
• Addresses symptoms like ice falling outside the bin, frequent jams, or a broken/missing chute
• Molded plastic design resists normal freezer conditions

• Disconnect power to the refrigerator before starting work
• Remove the ice bin and any obstructing trim to access the guide
• Align tabs with mounting slots and press until the guide snaps into place; do not force
• If icy buildup is present, defrost or clear ice before installing to ensure proper fit

This separator is a molded baffle that helps position and isolate internal components to ensure proper airflow and reliable operation. Replaces a worn or broken separator to restore correct internal alignment and reduce noise or rubbing. What it does:

• Keeps internal parts separated and secured to prevent contact or misalignment
• Directs or channels airflow where required for proper operation
• Helps reduce vibration noise caused by loose or shifted components
• Prevents chafing or rubbing that can lead to premature wear on nearby parts

• One separator/baffle as shown

• Refer to your model's exploded parts diagram for correct placement and orientation
• Disconnect power (and water, if applicable) before beginning repairs
• Use basic hand tools; avoid forcing the part into place to prevent damage
• If other plastic mounting tabs are damaged, inspect and replace those parts as needed

This replacement plastic ice scoop makes it easy and sanitary to transfer ice from the bin to glasses or trays. Durable, lightweight design restores convenient ice handling after the original scoop is lost or worn. What it does:

• Provides a hygienic way to scoop and serve ice without using hands
• Fits standard refrigerator ice bins and buckets for easy access
• Helps prevent spills and keeps ice contained while serving
• Replaces missing, cracked, or discolored scoops to restore everyday use

• No tools required — simply place scoop in the ice bin or store in a convenient location
• Wash before first use and after each use with warm, soapy water
• Keep away from high heat to avoid warping or damage
• Not an electrical component; disconnecting power is not required for replacement

This replacement ice door is the dispenser flap that opens and closes to release ice from the freezer into the dispenser chute, restoring normal ice delivery and helping keep the dispenser sealed when idle. What it does:

• Replaces a cracked, warped, or broken dispenser/ice door that won't open or close properly
• Helps stop ice from jamming or falling into the dispenser area
• Restores the seal that keeps warm air out of the ice chute
• Works with the dispenser actuator to allow normal ice dispensing

• Disconnect power to the refrigerator before starting any work.
• Remove the dispenser housing trim per your model's service instructions to access the door; handle carefully to avoid damaging surrounding components.
• Inspect the actuator arm and mounting tabs during install; replace or realign if worn or broken.
• Test dispenser operation after installation to ensure the door opens and closes smoothly.

The Ice Scoop is an OEM part for Whirlpool refrigerators. This accessory is designed to make scooping ice from your refrigerator's ice bin easier. It features a comfortable handle and a well-designed scoop, allowing you to easily serve ice for your beverages or other cooling needs.

A bad ice scoop can occur due to wear and tear, damage, or loss. If you find yourself struggling to scoop ice or if your current ice scoop is damaged or missing, it's time to replace it with this genuine OEM part.

Symptoms of a bad ice scoop include:

• Difficulty in scooping ice
• Broken or cracked scoop
• Missing or lost ice scoop

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

The Ice Maker Cooling Duct is an OEM part for Frigidaire refrigerators. It directs cold air flow to the ice maker.

Causes of failure can be blockages or damage to the duct over time that impact efficient air flow.

Symptoms of a bad cooling duct include:

• Inconsistently shaped or formed ice cubes
• Slow or reduced ice production
• The ice maker failing to dispense ice properly
• Higher than normal interior refrigerator temperatures near the ice maker

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models. 

The Refrigerator Ice Seal Cover is an essential component for maintaining the efficiency and performance of your Samsung refrigerator. This genuine OEM part is specifically designed to ensure a secure and airtight seal around the ice compartment, preventing unwanted moisture and ice buildup. Crafted from durable materials, the seal cover offers long-lasting protection, helping to keep your ice maker functioning optimally. Installing the Refrigerator Ice Seal Cover is straightforward, allowing you to replace any cracked, worn, or damaged seals easily without the need for professional assistance. By maintaining the integrity of your refrigeratorGÇÖs ice system, this part contributes to better energy efficiency and helps preserve the freshness of your stored items. Compatible with a range of Samsung refrigerator models, the Refrigerator Ice Seal Cover guarantees a perfect fit and reliable performance. Enhance your applianceGÇÖs functionality and ensure a seamless user experience with this high-quality, genuine OEM part.

This outer front panel replaces a worn, cracked or damaged front cover to restore the appliance's appearance and protect internal components. It matches OEM form and fit for an exact external repair. What it does

• Covers and protects internal components at the front of the appliance.
• Restores a finished appearance if the original front panel is dented, cracked or scratched.
• Helps keep lint, dust and debris away from internal parts behind the panel.
• Supports proper alignment of control and door openings (when applicable).

• One front cover (single outer front panel) as shown.

• Installation requires basic tools; remove power and disconnect appliance before starting.
• Support the cabinet or door while removing fasteners to avoid damage or injury.
• Retain and re-use any original screws, clips or gaskets unless replacements are supplied separately.

This ice guide directs ice from the ice maker into the bin or dispenser, reducing jams and misfeeds for smoother ice delivery. Durable molded plastic fits into the ice path to keep cubes aligned as they drop. What it does

• Guides ice from the ice maker to the storage bin or dispenser chute
• Helps prevent cubes from getting stuck or misdirected during harvest
• Maintains a clear path to reduce clumping and improve dispensing consistency
• Replaces a cracked, broken, or missing plastic guide

• One ice guide

• Disconnect power to the appliance before starting any work
• Remove the ice bin or access panels as needed for clear access
• Usually installs by snapping into place or securing with the existing fastener(s); do not force parts