Refrigerator Ice Maker & Related

The Refrigerator Ice Maker Assembly is an essential component for maintaining a steady supply of ice in your Samsung refrigerator. This genuine OEM part ensures perfect compatibility and seamless integration with your appliance, providing reliable performance you can count on. Crafted with durable materials, the ice maker module is designed to withstand regular use, delivering consistent ice production without compromise. Installing this replacement part is straightforward, allowing you to restore your refrigeratorGÇÖs ice-making capabilities quickly and efficiently. By choosing the Refrigerator Ice Maker Assembly , you benefit from the same quality and functionality as the original component, ensuring your fridge operates smoothly. Whether your current ice maker is malfunctioning or has been damaged, this genuine OEM part is the ideal solution to enhance your refrigeratorGÇÖs performance and extend its lifespan. Enjoy the convenience of fresh ice whenever you need it with this reliable and high-quality ice maker assembly.

This refrigerator ice maker assembly automatically freezes water and harvests cubes so you have a steady supply of ice in the freezer. Replacing a failed assembly restores consistent, hands-off ice production.

• Freezes water in the mold and ejects cubes on a controlled cycle
• Signals the water inlet valve to refill after each harvest
• Pauses production when the bin is full via the unit's shutoff mechanism
• Common signs of failure: no ice production, won't eject or refill, intermittent cycling, or very small/hollow cubes

• Unplug the refrigerator and shut off the water supply before servicing
• Take photos of wiring and mounting to match connections and positions during reassembly
• Reuse any model-specific brackets or covers from the original unit if required
• After installation, restore power/water and allow several hours for the first batches

This is the condenser fan motor for select LG-built refrigerators. It drives the outside rear fan that pulls air across the condenser coils and over the compressor to remove heat so the refrigerator can cool efficiently.

• Circulates air through the condenser section to dissipate heat
• Helps prevent overheating of the compressor
• Common failure symptoms: fridge not cooling well, compressor running hot, loud or grinding noise from rear bottom, fan not spinning
• May run intermittently or seize when failing

• Disconnect power before servicing; use cut-resistant gloves
• Access from the rear lower service panel near the compressor
• Note wire orientation and fan blade position before removal
• After replacement, ensure the fan spins freely and no wiring contacts the blade

This small plastic control arm extension links to the mechanism it serves, restoring proper movement and engagement so the appliance can operate as intended. It's a simple, direct-replacement component designed to snap in and align correctly.

• Connects to the existing control arm to extend its reach and function
• Helps correct issues like improper engagement or intermittent operation
• Can address symptoms such as sticking, misalignment, or failure to activate
• Sized to fit the original mounting points for consistent motion

• Disconnect power (and water if applicable) before servicing
• Note the orientation of the original part to match during reassembly
• Inspect the mating control arm and linkage for wear or damage
• Test operation before fully reassembling panels or covers

The Ice Maker Scoop is an OEM component specifically designed for Whirlpool ice machines. As an included accessory, it provides a sanitary and convenient way for users to fetch ice from the storage bin.

The scoop is strategically designed with an ergonomic handle and wide opening bowl shape. This facilitates easy scooping and transport of ice cubes without spillage or crumbling. Its food-safe materials maintain hygienic conditions in the storage area. 

Symptoms of a faulty scoop include:

• Cracks or breaks that compromise the scooping surface 
• Leaks or spills of ice when trying to scoop
• Sharp edges that risk cuts or scratches
• Warping or loosening of the handle attachment over time

This OEM Whirlpool scoop is also compatible with some Scotsman and Manitowoc ice machines. Replace yours today to restore safe and hygienic ice retrieval from the storage bin.
 

This replacement ice bin stores the ice produced by your refrigerator's icemaker and fits into its designated compartment for easy access. Replace a cracked or warped container to restore reliable ice storage and smooth dispensing.

• Holds harvested ice until use
• Guides cubes toward the dispenser outlet
• Restores proper fit when the original bin is cracked, broken, or warped
• Common symptoms: ice won't dispense or jams; ice spills into the freezer; bin won't seat or latch properly

• Unplug the refrigerator or disconnect power before servicing
• Empty and remove the old bin from the compartment
• Align and slide the new bin into position until fully seated
• Restore power and allow time for new ice to accumulate

The Ice Container Assembly is an OEM part for Frigidaire refrigerators. This assembly stores batches of fresh ice for retrieval.

Causes of a bad ice container can include cracks or damage allowing water to leak or ice to melt prematurely. Hinges or latches may weaken over time. Mineral deposits may clog drains and hamper ice ejection.

Symptoms of a bad ice container assembly include:

• Ice crushing or cracking inside the container
• Inability to fully rotate or lift the container out
• Water puddling inside versus stored as intended
• Ice frozen together into a solid block

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This coupling is the small connector that links a drive motor to its mating component, transferring rotation so the appliance operates smoothly. Replacing a cracked or stripped coupling restores reliable drive and helps prevent further wear.

• Connects the motor shaft to the driven part to transmit torque
• Maintains alignment to reduce wobble and slippage
• Failure signs can include no movement, intermittent operation, clicking/grinding, or visible cracks/rounding
• Restores consistent motion of the connected part once replaced

• Disconnect power (and shut off water/gas if applicable) before servicing
• Access the drive area and remove any covers/tray/drive components as needed
• Pull the old coupling straight off the keyed or D-shaped shaft; clean and inspect the shaft
• Align and press the new coupling fully onto the shaft, reassemble, and test

This ice bin assembly stores the cubes your icemaker produces and makes them easy to access or dispense. Replacing a cracked or worn bin prevents spills and jams and keeps your refrigerator's ice service working smoothly.

• Collects and holds ice produced by the icemaker
• Slides in and out for convenient ice access
• Helps prevent stray cubes and spills inside the freezer
• Common symptoms of failure: cracked or broken bin, ice spilling, difficulty dispensing or removing ice

• Disconnect power before servicing for safety
• Empty and remove the old bin per your model's procedure
• Seat the new bin fully on its rails or locator tabs
• Restore power, make a small batch of ice, and check operation

This ice maker assembly replaces the complete cube-making unit in your refrigerator. It restores automatic freezing, harvesting, and bin-level shutoff so your appliance can reliably produce a steady supply of ice again.

• Freezes water in the mold and ejects cubes into the ice bin during each harvest cycle
• Pauses production when the bin is full via the built-in shutoff mechanism
• Typical failure symptoms: no ice production, cubes not ejecting or stuck mid-cycle, intermittent clicking/grinding from the module
• Can replace a cracked or seized ice mold assembly that jams or leaks at the icemaker

• Disconnect power and shut off the refrigerator's water supply before servicing
• Remove the ice bin; loosen mounting screws and unplug the wire harness to release the old unit
• Transfer any mounting brackets or covers from the original unit if needed; reuse existing hardware
• Restore power and water; ensure the fill tube is clear and allow the icemaker to begin cycling

The Icemaker is an OEM component specifically designed for Whirlpool refrigerators. As the name implies, it is responsible for automatically producing ice through the process of harvesting and manufacturing. The icemaker freezes water into individual ice cubes and deposits them into the ice bin.

Causes of a bad icemaker can include clogged or frozen water lines preventing proper water flow, malfunctioning electronic controls that fail to trigger harvesting and freezing cycles, or damage and wear to mechanical components like gears or augers.  

Symptoms of a bad icemaker include:

• No ice production over multiple cycles  
• Inconsistently sized or misshapen cubes
• Cubes that fuse together or fail to eject properly
• Leaks or drips from the icemaker area
• Loud knocking or grinding noises during the operation

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Refrigerator Ice Guide Assembly is essential for maintaining smooth ice dispensing in your Samsung refrigerator. This genuine OEM part ensures that ice cubes flow efficiently from the ice maker to your desired location, enhancing the overall functionality of your appliance. Designed specifically for Samsung refrigerators, the Refrigerator Ice Guide Assembly guarantees a secure fit and seamless integration with your existing system. Its durable construction prevents jams and minimizes ice dispensing issues, providing a reliable solution for your kitchen needs. Installing this genuine OEM part restores the optimal performance of your ice dispensing feature, ensuring you enjoy fresh ice whenever you need it. Whether your original ice guide is cracked, broken, or no longer functioning correctly, the Refrigerator Ice Guide Assembly offers a straightforward and effective replacement. Enhance your refrigeratorGÇÖs performance and enjoy the convenience of consistent ice flow with this high-quality, customer-focused replacement part.

The Ice Cube Tray is an OEM part for Whirlpool refrigerators. This tray is designed to fit securely in the freezer compartment and is used to form and hold ice cubes. The tray ensures that ice cubes are consistently shaped and easily removable for everyday use. The tray measures about 8-1/2 inches wide by 11 inches deep.

Over time, ice cube trays can become damaged or worn due to repeated use, exposure to cold temperatures, or mishandling. Cracks or warping in the tray can lead to leaks or difficulties in removing the ice cubes.

Symptoms of a bad ice cube tray include:

• Cracked or broken sections
• Difficulty in removing ice cubes
• Leaks or water pooling in the freezer
• Misshapen or irregular ice cubes

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

This replacement ice container assembly stores and delivers ice from the freezer to the dispenser. Replacing a cracked or jammed bin restores smooth cubed/crushed dispensing and dependable ice flow.

• Holds harvested ice in the freezer and interfaces with the dispenser
• Feeds ice toward the chute when you press the dispenser lever
• Supports cubed or crushed selections (as designed for your model)
• Common symptoms: won't dispense, dispenses slowly, only cubes or only crushed, cracked/warped bucket, grinding or jamming noises

• Unplug the refrigerator and wear cut-resistant gloves
• Empty remaining ice, release and lift out the old bin, then slide the new assembly fully into place
• Restore power and test both cube and crush functions at the dispenser

This Arm-Stripper is the factory replacement stripper arm that restores the original part that guides and supports related moving components, helping the appliance operate smoothly and quietly. What it does

• Positions and guides the component it mates with to prevent binding or misalignment.
• Helps maintain proper contact/clearance between moving parts for reliable operation.
• Prevents rubbing or wear that can cause noise or uneven performance.
• Common signs it may be needed: rubbing or scraping noises, part misalignment, or erratic movement where the arm is located.

• One Arm-Stripper replacement part.

• Recommended for users familiar with basic appliance repair; verify power is disconnected before starting.
• Inspect surrounding clips, fasteners and mating parts; replace damaged hardware as needed.
• Handle carefully to avoid bending or damaging the arm during installation.

Optional flexible ice tray for those that dont have an icemaker