Need Help?
Call
Fix dirty water backing up into your dishwasher with this check valve assembly. Prevents backflow from sink disposal. Easy 30-minute DIY repair.
I checked the drain hose for blocking at the garbage disposal and then at the connection point to the dishwasher. The hose was clear and nothing was obviously obstructing where the drain hose connects to the dishwasher. At this point I Googled the model number with the term "will not drain" and immediately landed on the AppliancePartsPros.com website. At the Drain & Wash Impeller Kit page amazingly had a video showing the technician replacing the impeller on a dishwasher essentially the same as... Read more
Ice maker not filling or water dispenser not working? This water inlet valve controls flow to your refrigerator's ice and water system. DIY repair.
Order new valve Read more
This is a water inlet valve with a built-in bimetal thermistor, used in washing machines to control the flow of water into the tub. The integrated thermistor helps regulate water temperature by sensing incoming water conditions. Replace this valve if the washer won't fill, fills with the wrong water temperature, leaks near the water connections, or continues running water when it shouldn't.
I order the part from appliance parts recieed it in one day and it was repaired the next day so simple watched video thanks to you all is well i highly recommend you to anyone barbara mcallister Read more
Leaking from the water inlet connection? This vacuum break prevents backflow and maintains the air gap at the inlet. Easy DIY fix in under 30 minutes.
Removed cover from Whirlpool washer (~20 years old) and found water to be leaking from hose connection at Break Vac. Obviously the hose had to be replaced but the Break Vac looked corroded and partially plugged, too, possibly inhibiting water flow. While the cabinet was off I noticed the Suspension Spring was rusted off so I ordered 1 of those, too. Total of all parts was under $45 so looks like we won't be getting a newer, more efficient washer anytime soon. Everything arrived in 3 days and... Read more
This is a water inlet valve that controls the flow of water into the washing machine during fill cycles. It is an electrically operated valve that opens and closes to allow hot or cold water into the tub as directed by the control board. Replace this valve if your washer is not filling with water, filling slowly, leaking from the back, or continuing to fill when it should stop.
Ordered this part and just changed it out. Not hard once I figured out how to get in to it. Read more
This is an electrically operated water inlet valve assembly with a built-in vacuum break (backflow preventer) for a washing machine. It controls the flow of hot and cold water into the wash tub when the machine fills during a cycle. Replace this valve if the washer is not filling with water, fills slowly, continues to fill when it should stop, or if you notice water leaking from the valve area.
New valve. Read more
This water inlet valve controls the flow of water into the washing machine during fill cycles. It uses an electrically operated solenoid to open and close in response to signals from the control board. Replace this valve if your washer is not filling with water, filling slowly, leaking from the back, or continuing to fill when it should stop.
The problem wasn't a blocked screen. I took apart my washer. Very easy on the Kenmore 600 series. Before I did this, I watched a YouTube video and it was a piece of cake. The whole job took me 35 minutes. Read more
Fix dishwasher overfilling or not filling with water by replacing the float assembly. Common issue with sticky buildup preventing proper operation.
I cleaned all the jet nozzles with a toothpick and a pipe cleaner to remove the hard water deposits. I then replace the ring bearing under the bottom spray wand and the ring bearing under the upper spray wand. I also replaced the smaller radial ring bearing. Although none of them looked overly worn, it doesn't take much to cause the spray wands to spray inadequately. Then, I replaced the float and washer assembly. Although it appeared to work properly when I lifted up on it and let it down, it... Read more
If your dishwasher shuts off mid-cycle or leaks water, a warped or stuck overfill float may be the cause. This 5-minute fix restores proper fill control.
Replace the motherboard and used YouTube to replace float switch. Part ordered was exactly what I needed Read more
Oven won't heat but igniter glows? This safety valve controls gas flow to the burner. Common fix for ranges with no heat. Moderate DIY repair.
Fix dishwasher overflows or won't fill issues. This water level float detects proper fill levels. Replaces broken or stuck floats causing drainage problems.
Usually ships within 4 - 14 days
If your range burner won't ignite, stays on low heat, or has uneven flames, the top burner valve may need replacement. Compatible with gas ranges.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.