Roper Fuse Or Sensor

• Won't start
• Timer will not advance
• No heat or not enough heat
• Touchpad does not respond

I did the recommended checks of parts as listed on the website. I would recommend as one other person did but I did not listen the first time and that is to check all the parts don't stop at the first part you find bad. As I had to make two orders paying shipping twice because I thought I found a bad part when testing the igniter but the thermal fuse was also bad and since in a different part of the machine I did not take the time to check it, bad mistake. Also one tool mentioned in the video... Read more

• Too hot
• Timer will not advance
• Takes too long to dry
• Doesn't shut off

After 22 years my Kenmore (Whirlpool) dryer stopped getting hot. So I went ahead and reviewed the videos and figured I could repair it myself. It should be noted that the only part that failed the Ohm test was the thermal fuse. However, I figured that since I have it apart, I might as well go ahead and replace the heating element and the cycling thermostat. Here is a rundown of what I did and how long it took: • Taking the back off and vacuum <1 minute • Finding the components (from the... Read more

• Timer will not advance
• No heat or not enough heat
• Too hot
• Doesn't shut off

After 22 years my Kenmore (Whirlpool) dryer stopped getting hot. So I went ahead and reviewed the videos and figured I could repair it myself. It should be noted that the only part that failed the Ohm test was the thermal fuse. However, I figured that since I have it apart, I might as well go ahead and replace the heating element and the cycling thermostat. Here is a rundown of what I did and how long it took: • Taking the back off and vacuum <1 minute • Finding the components (from the... Read more

I used the Appliance Parts Pros d.i.y. video to get some oversight on the repair; ordered the parts (heating element, Hi-Limit T-stat and Dryer Thermal Cut-Off kit). I unplugged the electric; disconnected the exhaust duct; moved the clothes dryer so that I could remove the back sheet metal panel. The electrical connection at the heater "Stacon" terminal was corroded and broken - an open circuit. This had happen about 10 years before and I was familiar with this problem. After removing the... Read more

• Shuts off too soon
• No heat or not enough heat
• Takes too long to dry

I used Fixya as an initial source describing my problem. I got two responses which were very helpful. One that the "coils" were probably the problem. Two, that the problem could be the thermostat or a thermistor in the dryer. I verified that AC was coming from the timing control, that both the two terminal and three terminal coils,the igniter and shut off thermostat all had continuity. I then applied AC directly to the coils: the two terminal coil ""clanked" and I interpreted that as the coil... Read more

• No heat or not enough heat
• Too hot

Since the dryer was 24 years old I opted to replace all the possible problem components, instead of just the bad one. The parts aren't that expensive and do to their age I figured it was worth it to avoid having to go back into the dryer in a few months. The repair was surprisingly easy and went pretty much as the video instruction AppliancePartPros provided with one exception. Because, my model was much older than that used in the video, I had a more difficult time replacing the Heating... Read more

• Not drying dishes properly

My Whirlpool dishwasher (wdf520padm3) started leaving food on dishes and not drying dishes as well as it used to, even when I ran the 'high temp' and 'heavy' cleaning options. This started happening after about 3 years of operation. To try to diagnose the issue, I started the diagnostics cycle (see below for instructions on how to do this). However, the 'Clean' LED is also not working on my dishwasher, so I was unable to read the error code after the service cycle finished. I decided to... Read more

• Won't start

Ordered a new thermal fuse from your website last week and installed it three days ago. This is the second fuse in one year that needed to be replaced. The dishwasher was purchased new in 2012. Relatively easy to replace. Your website had a you tube video that showed how to replace it. Power came back on the control panel, but the start button (not a button, but a touch screen) would not work. This is the second time in two years that the control panel had to be replaced because the start... Read more

• Oven is too hot
• Won't start
• Little to no heat when baking

Spoke to a parts pro and told them of the problem. there were 2 possibilieies from the explanation of what the parts do. onw could have been the Range oven igniter. that wasn't it beaacause the over was lighting fine. by process of illimination it was the Oven Sensor Assembly. Read more

My wife said we have a problem with our dishwasher (Whirlpool WDT920SADE2). The dishes were not getting clean, and the soap dispenser opened, but soap was still dribbled down the inside of the door and on the silverware caddy. I'm not the handiest guy; it took me several days to go through the trouble-shooting process, watching multiple videos and trying different things. My initial guess was that the soap dispenser was opening too late. (This turned out to be wrong.) I started off by... Read more

Purchased, Igniter Kit, Gas Valve Coil Kit, and as a precaution Thermal Fuse and Cutoff-Tml. Was pretty confident the problem was the gas valve coil, but figured that why not just replace the other items while I had the unit apart. Researching and utilizing this site certainly helped me out in figuring what the problem may be. Watched the instruction videos which were very detailed and helpful. The replacement and repair was not that difficult and the work was done rather quickly. Doing... Read more

• Ice maker not making ice

I used your online troubleshooting tips and watched the videos on your site. I determined my thermostat was defective, ordered the thermostat which arrived in two days and I replaced the thermostat and I now have a full bin of ice !!! The do it yourself video was extremely helpful and made the repair very easy. Thanks so much for the great service and quick delivery !!! Read more

Replaced the blown heating element. I also only to be on the safe side, replaced the over temp sensor. I checked it with the meter when I pulled it out and it was ok. Tested ok. Thank you very much for the less than 2 day delivery on the part. Read more

• Too hot
• No heat or not enough heat
• Shuts off too soon
• Takes too long to dry

This Maytag dryer was bought in 1985 if memory serves. It has worked hard with few repairs done by yours truly over the years. Thanks to the engineering and excellent design by Maytag staff, removing parts are relatively easy. Once I opened the unit, I found it to be full of lint. I cleaned the entire inside and the vent pipe duct work. I found the blower wheel assembly worn. Though it was not cause of my problem, I decided to change it along with the igniter, heater relay and the fan belt. I... Read more

• Won't start

I first verified the house panel circuit breaker was not tripped. It wasn't so I removed the bottom kick plate of the unit, using a circuit cricket I verified the power feed to the unit was live. The bottom kick plate had a trouble shooting guide in a plastic sleeve which I opened and reviewed. Based on information in there it appeared the TOC was likely the issue. (We recently lost power and used a stand by generator. Previously when we did the the dishwasher had a blinking LED on the... Read more

Changed parts Read more