Kenmore Power Snowblower V-Belt Parts

• Won't start
• Timer will not advance
• No heat or not enough heat
• Touchpad does not respond

I did the recommended checks of parts as listed on the website. I would recommend as one other person did but I did not listen the first time and that is to check all the parts don't stop at the first part you find bad. As I had to make two orders paying shipping twice because I thought I found a bad part when testing the igniter but the thermal fuse was also bad and since in a different part of the machine I did not take the time to check it, bad mistake. Also one tool mentioned in the video... Read more

• Will not tumble
• Noisy

Our Whirlpool Duet Sport Dryer, 6.7 cu. ft, Model WED8300SW0, bought new 8 years ago (2006), developed a VERY loud squeaking noise inside the dryer. Removing the top panel did not isolate the problem. I researched the problem and through the videos appearing on Appliance Parts Pros (APP) website and a few others, determined that the problem was either the drum belt, one or more of the 4 drum support rollers, or idler pulley or any combination of these. I ordered the kit to allow for... Read more

• Heat stays on after drum has stopped
• Will not tumble
• Touchpad does not respond
• No heat or not enough heat

Unpluged dryer first. Then took the lint filter out and removed the two philips screws inside the lint filter lid. Then take a paint scraper just under the top of the dryer two inches from the left front corner and pushed in a little to release the snap connector and did the same on the right side. Then lifted top over. Then take a 5/16 socket or nut driver and remove the two screws on on the left inside panel, then the right side. Lean front out a little and remove the two wires one the back... Read more

• Too hot
• Timer will not advance
• Takes too long to dry
• Doesn't shut off

After 22 years my Kenmore (Whirlpool) dryer stopped getting hot. So I went ahead and reviewed the videos and figured I could repair it myself. It should be noted that the only part that failed the Ohm test was the thermal fuse. However, I figured that since I have it apart, I might as well go ahead and replace the heating element and the cycling thermostat. Here is a rundown of what I did and how long it took: • Taking the back off and vacuum <1 minute • Finding the components (from the... Read more

• Will not tumble
• No heat or not enough heat

I was out of the country when the damage occurred but based on my wife's description I knew what had happened. Upon returning to the 1st World, i verified a totally free-spinning drum and ordered a full rebuild kit (rollers, belt & idler). The instruction video was very helpful - especially in listing every single tool needed so i only made one trip to the workshop and brought up exactly what i needed, the first time. Everything went pretty much according to the instructions except that... Read more

First, I did a search based on the problem I had with my model of dryer. The model number was on the door frame and was visible when I opened the dryer door. The problem was, when I pressed the button to start a dryer cycle, I heard a clicking noise and the indicator text changed to "Drying", but I could not hear or see the dryer drum turning. The search led me to a page that indicated my problem was usually one of 3 common causes. 1. Faulty door switch 2. Broken Drum drive belt 3. burned out... Read more

• Timer will not advance
• No heat or not enough heat
• Too hot
• Doesn't shut off

After 22 years my Kenmore (Whirlpool) dryer stopped getting hot. So I went ahead and reviewed the videos and figured I could repair it myself. It should be noted that the only part that failed the Ohm test was the thermal fuse. However, I figured that since I have it apart, I might as well go ahead and replace the heating element and the cycling thermostat. Here is a rundown of what I did and how long it took: • Taking the back off and vacuum <1 minute • Finding the components (from the... Read more

• Too hot
• Shuts off too soon

I am not an electrician, just a housewife with limited funds and a desire to DIY. I used the provided videos for knowing how to replace everything except the heating element which I just guessed based on other reviews and seeing how the other parts worked. Our dryer is 11 years old Whirlpool Gold HE and I have only ever cleaned the lint tray. My husband replaced the belt about five years ago and he did clean out the inside of the dryer. Started by ordering a thermal fuse because it was... Read more

I used the Appliance Parts Pros d.i.y. video to get some oversight on the repair; ordered the parts (heating element, Hi-Limit T-stat and Dryer Thermal Cut-Off kit). I unplugged the electric; disconnected the exhaust duct; moved the clothes dryer so that I could remove the back sheet metal panel. The electrical connection at the heater "Stacon" terminal was corroded and broken - an open circuit. This had happen about 10 years before and I was familiar with this problem. After removing the... Read more

• Will not tumble

It was the day of my birthday June 6th when my wife came to me to tell me that the dryer was not working. Immediately I started to look for a new dryer from Best Buy and the rest. Then I said It would be better if I waited for 4th of July at which time I could find a better deal. This is when I decided to take it apart to see what was wrong. Initially, I thought of the belt that could be broken and I rotated the drum by hand and I heard a noise of the belt at times falling on the drum. I was... Read more

• No heat or not enough heat
• Won't start

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

• Won't start

From watching the video I got the general idea, disassemble 50% of the dryer. Only had 2 differences in my dryer from the one used in the video, so the video was helpful. The one difference was the connections to the front side of the dryer were on the power distribution circuit board located on the left of the dryer under a sheet metal cover. These were harder to disconnect with my fat thumbs. The bigger issue was with removing the front control panel. In the video there doesn't appear to be... Read more

• Too hot

I am not an electrician, just a housewife with limited funds and a desire to DIY. I used the provided videos for knowing how to replace everything except the heating element which I just guessed based on other reviews and seeing how the other parts worked. Our dryer is 11 years old Whirlpool Gold HE and I have only ever cleaned the lint tray. My husband replaced the belt about five years ago and he did clean out the inside of the dryer. Started by ordering a thermal fuse because it was... Read more

• Will not tumble

I found a video on Youtube which described dryer drum squeaks as most likely caused by a worn rear drum bearing. I located the model number on the inside lip of the dryer door: Frigidaire Affinity LEQ6000ES2. I googled "frigidaire affinity dryer squeak". I got a link for my friends at AppliancePartsPros.com! I've used Appliance PartsPros 3 times before, so I figured I was in a "one-stop-solution" situation. I ordered a rear drum bearing kit as well as a dryer drum belt (after nearly 7 years... Read more

• Will not tumble

I disassembled/reassembled the dryer according to the ApplianceParts Youtube video. With my limited electrical knowledge (just enough to be dangerous) I initially figured it was a problem with the heating unit, sensor(s), or the control board. After diagnosing the problem (bad thermistor), I had to order the parts and was able to repair and reassemble the dryer several days later. After removing the drum, I cleaned all the dust etc. out of the inside (it gets dirty in there!) and inspected,... Read more

• Won't start

You can do this! Although an Art Director by trade, I like working with my hands. I’m adept at working with tools and following instructions. In today’s disposable society, I prefer fixing things. That said, this has to be the easiest repair I’ve ever attempted with the largest cost-savings versus hiring a professional. My brand new dryer had been in use fewer than six months (average 6 loads per week) when suddenly the dryer would not heat. The drum would spin, there were no error codes, and... Read more