Snowblower Cogged Belt Parts

• Will not tumble
• Noisy

Our Whirlpool Duet Sport Dryer, 6.7 cu. ft, Model WED8300SW0, bought new 8 years ago (2006), developed a VERY loud squeaking noise inside the dryer. Removing the top panel did not isolate the problem. I researched the problem and through the videos appearing on Appliance Parts Pros (APP) website and a few others, determined that the problem was either the drum belt, one or more of the 4 drum support rollers, or idler pulley or any combination of these. I ordered the kit to allow for... Read more

• Heat stays on after drum has stopped
• Will not tumble
• Touchpad does not respond
• No heat or not enough heat

Unpluged dryer first. Then took the lint filter out and removed the two philips screws inside the lint filter lid. Then take a paint scraper just under the top of the dryer two inches from the left front corner and pushed in a little to release the snap connector and did the same on the right side. Then lifted top over. Then take a 5/16 socket or nut driver and remove the two screws on on the left inside panel, then the right side. Lean front out a little and remove the two wires one the back... Read more

• Will not tumble
• No heat or not enough heat

I was out of the country when the damage occurred but based on my wife's description I knew what had happened. Upon returning to the 1st World, i verified a totally free-spinning drum and ordered a full rebuild kit (rollers, belt & idler). The instruction video was very helpful - especially in listing every single tool needed so i only made one trip to the workshop and brought up exactly what i needed, the first time. Everything went pretty much according to the instructions except that... Read more

First, I did a search based on the problem I had with my model of dryer. The model number was on the door frame and was visible when I opened the dryer door. The problem was, when I pressed the button to start a dryer cycle, I heard a clicking noise and the indicator text changed to "Drying", but I could not hear or see the dryer drum turning. The search led me to a page that indicated my problem was usually one of 3 common causes. 1. Faulty door switch 2. Broken Drum drive belt 3. burned out... Read more

• Won't start

From watching the video I got the general idea, disassemble 50% of the dryer. Only had 2 differences in my dryer from the one used in the video, so the video was helpful. The one difference was the connections to the front side of the dryer were on the power distribution circuit board located on the left of the dryer under a sheet metal cover. These were harder to disconnect with my fat thumbs. The bigger issue was with removing the front control panel. In the video there doesn't appear to be... Read more

• Will not tumble

It was the day of my birthday June 6th when my wife came to me to tell me that the dryer was not working. Immediately I started to look for a new dryer from Best Buy and the rest. Then I said It would be better if I waited for 4th of July at which time I could find a better deal. This is when I decided to take it apart to see what was wrong. Initially, I thought of the belt that could be broken and I rotated the drum by hand and I heard a noise of the belt at times falling on the drum. I was... Read more

• Will not tumble

I found a video on Youtube which described dryer drum squeaks as most likely caused by a worn rear drum bearing. I located the model number on the inside lip of the dryer door: Frigidaire Affinity LEQ6000ES2. I googled "frigidaire affinity dryer squeak". I got a link for my friends at AppliancePartsPros.com! I've used Appliance PartsPros 3 times before, so I figured I was in a "one-stop-solution" situation. I ordered a rear drum bearing kit as well as a dryer drum belt (after nearly 7 years... Read more

This was my first attempt, ever, to repair a washing machine. After some internet research on the problems, I was able to determine that the shaft seal on the gearcase probably was leaking water into the gearcase with each use. No water was ever found on the floor, but when I turned the washer over to inspect the gearcase, I found a black, oily residue on the outside of it along with the same residue on the pulleys, the belt and the motor. I ordered a new gearcase, shift actuator, splutch... Read more

• Will not tumble

I disassembled/reassembled the dryer according to the ApplianceParts Youtube video. With my limited electrical knowledge (just enough to be dangerous) I initially figured it was a problem with the heating unit, sensor(s), or the control board. After diagnosing the problem (bad thermistor), I had to order the parts and was able to repair and reassemble the dryer several days later. After removing the drum, I cleaned all the dust etc. out of the inside (it gets dirty in there!) and inspected,... Read more

• Will not tumble

I watched your initial video which gave me some insight into the repair. I removed power from the dryer and positioned it for maintenance. Since my dryer was a Maytag, I needed to remove to two front bottom Phillips screws from the front panel of the dryer prior to pulling the panel and door assy. from the unit. The top of the dryer now needs to be removed. Two screws, one on each side holds the top of the dryer in place accessible from within and under the top of the dryer. Once those two... Read more

I replaced the belt, belt tension pulley, both dryer drum roller axles and both drum support rollers. Although I bought 2 tumbler bearing kits, because those still look good I am saving them for when they go bad. The videos were fantastic! I also took pictures as I went of wiring so there would be no question where things went when reassembling. It should be noted some models have extra terminals near the sensor terminals... just be aware and look closely/take pics as you are taking things... Read more

• Will not tumble

I went to the local Home Depot and Lowes, but they did not have the parts because they do not carry parts for the items they actually sell to people. Jumped on the phone and did a quick search for parts and came across appliancepartspros.com. I put in the make and model of my dryer and all the parts for the dryer where listed. I ordered the items on a Wednesday night. I opted for the two day shipping. I thought the items would be at my house by Friday but they did not arrive until Monday. I... Read more

• Spins slowly
• Burning smell
• Pumps but will not spin
• Noisy

The washer was on, and I heard a faint humming sound in the laundry room. I went in and opened the washer and it was full of soapy water in the middle of its cycle and was not agitating. I also smelled a faint burning smell. At this point I figured the problem was a bad motor, as the washer is more than 20 years old. I have fixed it twice before, because the first time, the repairman said I should keep this washer going as long as possible. It was made to last with a metal drum, unlike newer... Read more

I found a YouTube video, order the parts about midnight Saturday and-they came in the mail before lunch on Tuesday. I laid the washer on the rear panel, removed both pulleys to clean them, installed the speed sensor. bolted the pulleys back in place, installed the new belt-making sure it was centered and everything moved freely, and attached the belt/pulleys cover. I set the washer back up, reattached the water lines, placed the drain tube, and plugged in back in. Works like new !!! 30 minutes... Read more

Replaced the belt. Read more

• Burning smell
• Will not agitate
• Spins slowly
• Pumps but will not spin

I Purchased a new belt and replaced it. If I had not watched the video telling me how it is done the job would have been much more difficult. After watching the video I changed the belt in less than 2 minutes. I ordered the belt from Appliance Parts Pros and got it the next day. I am thankful that when I started my search I landed on your web site. Thanks for the quick service and the video. Read more