Admiral Washer Parts

• Will not agitate
• Spins slowly

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

• Pumps but will not spin
• Will not agitate
• Burning smell
• Touchpad does not respond

My whirlpool washer was no longer spinning, so my first stop was YouTube where I found the video from AppliancePartsPros showing how to replace the motor coupling. In addition to the replacement guide, Matt also shows you how to diagnose the problem by looking for rubber shavings under the washer. Seeing the rubber shavings under the washer, combined with the fact that the washer still drained meant that the motor was still working, so something else in the drive train was bad. I took the... Read more

After looking up the model number of my washing machine on AppliancePartsPros.com I ordered the suspension rod kit, two sets of tub centering springs (one spring per corner), a Ring-Tub (mine was breaking apart due to banging around) and a spare suspension bearing kit in case I need it later. I spoke to a very helpful customer service rep on the phone just before placing my order. They have customer service representatives answering the phone late at night. I was surprised. All of my parts were... Read more

Replaced washer drive block and Cam. I called around and finally settled on Appliance Parts Pros because they helped diagnose the problem, told me what parts to replace and had videos to show me how to do it. In completing the repair I had to remove quite a few pieces of hardware in order to get at the part I was to replace. The videos helped but there is a learning curve while you familiarize yourself with the parts and figure out how the remove them. Eventually I got to a large nut that,... Read more

I watched a video on YouTube that showed my exact problem. It had a link to this part AP5665171 Hub and it showed how to fix it. It was a fairly simple fix. I did not even have to remove the tub. I popped the cap on top of the agitator plate (AGP), removed the bolt hold the AGP on. I tapped on the bolt several time to loosen it. Using an angled screw driver, carefully and slowly lifted up the edges of the AGP until I could use my fingers to carefully pull the AGP off the splined drive... Read more

• Spins slowly
• Pumps but will not spin
• Burning smell

A couple of years ago, I had an issue with my Whirlpool washer which is every bit of 18 years old. I checked the internet for what might be wrong and stumbled across some how to videos on how to fix it. So, the other day, when my washer quit spinning the first thing I did is go to the internet again to see if I would be able to fix again. Thank you, Appliance Part pro.com, for your very helpful website with the very informative video's on how to replace parts! After I watched a... Read more

This was my first attempt, ever, to repair a washing machine. After some internet research on the problems, I was able to determine that the shaft seal on the gearcase probably was leaking water into the gearcase with each use. No water was ever found on the floor, but when I turned the washer over to inspect the gearcase, I found a black, oily residue on the outside of it along with the same residue on the pulleys, the belt and the motor. I ordered a new gearcase, shift actuator, splutch... Read more

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

Replaced suspension springs/rods and all associated bushings in the kit. Read more

The part is so new no video so I went onto a similar part and watched video that got me about 80%. Then, called and customer service sent me a service Manual but this still was not specific so I broke the old to get it out and in the process figured out how to do it correctly. So I installed the last bit of it which was the bezel through the machine top by myself correctly. So you take the old one out by pushing out to the right from the bottom side using a screw driver for leverage. It will... Read more

When I removed the cabinet, all of the springs appeared in tact, I had already replaced the counter balance spring so I knew that was not the issue. None of the suspension springs or brackets were broken but they did look worn/rusty so I replaced all of the brackets (2 in front and 1 large in back), all of the suspension spring retainers, and all of the suspension springs and it fixed the issue! I plan to also replace the Self leveling leg spring which is an easy fix since it's on the back of... Read more

• Won't start
• Timer will not advance
• Will not drain

First I checked the circuit breakers and power to the outlet, then next wanted to check the lid switch, but it wasn't where I had found it on older models. I could hear it clicking on and off as I raised and lowered the lid, but it wasn't visible. I drained the tub through a siphon hose to lighten the machine, so I could slide it away from the wall to better see. Couldn't see the switch anywhere and decided it must be hiding in the raised console, but was unsure of how to attack it without... Read more

• Lid or door won't close
• Won't start

Not wanting to spend hundreds of dollars on an appliance technician's service call, I searched online to troubleshoot the problems with my particular Maytag Washer Model Number MVWX500BW0. I stumbled across AppliancePartsPros.com and investigated there the most likely causes for my Maytag Washer's not agitating properly and not spinning at all. In order to acquire some additional information, I telephoned AppliancePartsPros.com and spoke with an extremely professional, knowledgeable and helpful... Read more

• Spins slowly
• Burning smell
• Pumps but will not spin
• Noisy

The washer was on, and I heard a faint humming sound in the laundry room. I went in and opened the washer and it was full of soapy water in the middle of its cycle and was not agitating. I also smelled a faint burning smell. At this point I figured the problem was a bad motor, as the washer is more than 20 years old. I have fixed it twice before, because the first time, the repairman said I should keep this washer going as long as possible. It was made to last with a metal drum, unlike newer... Read more

Installed new agitator Read more

• Leaking

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more