Microwave Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

After extremely poor support from WhirlpooI and researching numerous U-Tube videos, I fully troubleshot potential failed components and connections. All appeared to function properly, so I reassembled the unit and experienced the same problem as before. I then narrowed down the problem to either the Touchpad ($57+$8 shipping) or the control board ($295+shipping). If those did not work, then a new Microwave of better quality, reliability and support than original microwave, Unfortunately,... Read more

We bought a new filter. Read more

• Exhaust fan not working

Replacing this filter was very easy: two screws hold in the grill cover at the top of the microwave, and then the filter just slides in and out of its holder. There was quite a bit of grease in the area, probably pulled there by the vent from the stove top. I cleaned the grease up and also hand-washed the wire-mesh filter on the bottom of the microwave with soap and warm water. Airflow when running the vent is now noticeably better. Read more

• Doesn't shut off
• No heat
• Won't start

The first symptom was our microwave would continue to run after the time was up. The light would go out, the turn table would stop but you could still hear the microwave running and whatever was in it would continue to cook. The only way to stop it was to open the door. It was intermittent at first but eventually it would always run no matter what as long as the door was closed. Several other posts referenced these switches as the problem. I just replaced both and problem gone. It turns out... Read more

• Door won't close
• Door stuck closed

This was much easier than expected. I called Appliance Parts Pros with my model # and you told me what part I needed. It was shipped the same day and arrived the next day. I removed the inner door trim with a table knife ( don't rush this or you might crack the trim ). I then unhooked the old door latch disconnected the spring from the door hooked on the spring from the new latch and clipped in the latch to the door. Final step was to reattach the door trim. It was very easy and all I used... Read more

After checking other reviews, we decided it was best to replace the interlocks, cam and all three switches. You're going to need a phillips screwdriver, star driver, small screwdriver and needle nose pliers. You need to remove the ONE Phillips screw above the control panel inside the vent. The contol panel is on hinges that you can slide up and towards you. Using caution remove the wires noting how they're connected. Pinch the top of the white connectors and wiggle them free. We couldn't get... Read more

Vent snapped on at ease, but handle need a little modification(saw off a protruding plastic where the screws go) to get it sits flat on the door. Read more

After checking other reviews, we decided it was best to replace the interlocks, cam and all three switches. You're going to need a phillips screwdriver, star driver, small screwdriver and needle nose pliers. You need to remove the ONE Phillips screw above the control panel inside the vent. The contol panel is on hinges that you can slide up and towards you. Using caution remove the wires noting how they're connected. Pinch the top of the white connectors and wiggle them free. We couldn't get... Read more

• Won't start

Removed and replaced 3 door switches and mounting bar that holds switches plastic gets brittle with age and each switch comes out slightly different from each other, the chances of breaking a mounting pin is very easy. care should be taken when snapping mounting bar back into place to insure top latch and bottom latch locate properly insure bar is proper aligned when tightening screws their is free play in mounting bracket that could affect door properly engaging switches. NOTE that their are... Read more

• No heat
• Won't start
• shuts off after a few seconds

Knowing the odds of 2 failures occurring at the same exact time was unusually high, I just searched your site for what other broken items might affect these two failures. Came up with next control item upstream and tallied that item failure with percentages of successful repairs, (4 mins.) door safety switch. Since I had to change out the most likely of the 3 and since I was already was going to be into the switch panel I ordered all 3 and swapped them all out to cover my butt, as they were... Read more

Ordered mounting bracket but was surprised to find that the bracket model number had changed many times from the manufacter date of the microwave vent unit. Was hesitant if I was ordering the right part but I trusted the cross referencing of appliance parts pro and I got the exact bracket that I needed Read more

• Won't start
• No heat
• not self-cleaning

Did some Google searches and most comments concerning this issue on LG stoves indicated the high temperature thermostat malfunctions when using the self cleaning function. This malfunction causes complete loss of power for the entire stove and locks the oven door. Since I wasn't completely sure if it was the thermostat or where it was for that matter, I called a service tech to troubleshoot the stove. He was able to determine it was the thermostat and further tested his findings by... Read more

The first symptom was our microwave would continue to run after the time was up. The light would go out, the turn table would stop but you could still hear the microwave running and whatever was in it would continue to cook. The only way to stop it was to open the door. It was intermittent at first but eventually it would always run no matter what as long as the door was closed. Several other posts referenced these switches as the problem. I just replaced both and problem gone. It turns out... Read more

It was a really simple fix, and I kick myself for waiting so long to attempt the repair. Following the YouTube video, I had the old motor out and the new one in in approximately 10 minutes. I even felt the satisfaction of having completed a repair project. Read more

Check fan operation and was OK. Everything else worked except when microwave was started for a cycle. I looked around on internet and found someone had trouble with the door switches. I started to check door switches and found one shorted. I replaced both lower door switches and it took care of problem. Read more