Lnc8764a741 Parts

• Heat stays on after drum has stopped
• Will not tumble
• Touchpad does not respond
• No heat or not enough heat

Unpluged dryer first. Then took the lint filter out and removed the two philips screws inside the lint filter lid. Then take a paint scraper just under the top of the dryer two inches from the left front corner and pushed in a little to release the snap connector and did the same on the right side. Then lifted top over. Then take a 5/16 socket or nut driver and remove the two screws on on the left inside panel, then the right side. Lean front out a little and remove the two wires one the back... Read more

• Timer will not advance
• No heat or not enough heat
• Shuts off too soon
• Takes too long to dry

I'm starting with a quick background on my dryer. About 18 months ago the belt on the dryer started slipping and squealing. I had a can of belt dressing spray so I popped the top open and sprayed the belt. It actually worked for about a year before it started squealing again. For the next 6 months I had to spray it more and more often. Then the clothes stopped drying. Obviously, at this point, I had to get off my lazy ass and fix the dryer. Searched my dryer's model number on the internet and... Read more

• Shuts off too soon
• No heat or not enough heat
• Takes too long to dry

I used Fixya as an initial source describing my problem. I got two responses which were very helpful. One that the "coils" were probably the problem. Two, that the problem could be the thermostat or a thermistor in the dryer. I verified that AC was coming from the timing control, that both the two terminal and three terminal coils,the igniter and shut off thermostat all had continuity. I then applied AC directly to the coils: the two terminal coil ""clanked" and I interpreted that as the coil... Read more

• Too hot
• Shuts off too soon

I posted the following on the Facebook page ; SOoooo my 10 year old clothes dryer stopped and like almost everyone else I just figured it's shot, burned up, gotta get a new one. Well, due to a few bumps in the road I cannot afford another problem. My 2 vehicles are not running and with one being in the shop for 3 weeks and not being able to afford a rental car anymore this dryer was another headache. It sat for weeks and laundry started piling up. While looking online for sales somehow I... Read more

I removed the front panel of the dryer and the metal cover over the blower wheel. Removed the lock ring and clamp. Removed the old wheel and placed the new wheel on the shaft. I thoroughly cleaned all the lint around the area and inside the front cover. I resealed the metal cover over the blower and reinstalled the front cover. Dryer works great. Easy fix, I spent more time thoroughly cleaning all the lint. Read more

• No heat or not enough heat
• Takes too long to dry
• Noisy

Our Maytag gas clothes dryer was not drying like it should/used to and was making a lot of noise. After researching online I figured the vent was partially blocked and/or the blower wheel was bad. When I took it apart, the vent had very little lint in the lower elbow exiting the back of the dryer but the blower wheel was loose on the shaft and was missing the clamp. I cleaned out the vent and put a hose clamp on the blower wheel to tighten it to the shaft and tried it again. The noise was... Read more

• No heat or not enough heat

The root cause was the front glides. They were virtually gone, and the drum was on metal to metal. So I replaced them with a front glide kit. I also replaced the belt, rear rollers, and lint screen. I am happy to say all the parts fit perfectly, and I couldn't find a better price anywhere else. I will definitely keep you on file for the next time I need appliance parts! Thank you! Sincerely, pw Read more

• Door won't close
• Shuts off too soon
• Doesn't shut off
• Takes too long to dry

Ordered a new clip and installed it. Easy to do. Unplugged the dryer. Removed the front. It is only held on by two screws. Removed wires to the door switch. removed the female end (it had the broken male piece in it. Inserted the new female part in the front, clipped in the male part into the door and reconnected the door switch wires, screwed the front back on. Job done. Total time was less than 10 minutes. Works like new. Read more

I watched the video at your website. I unplugged the electric first. When I opened up the machine up, It was loaded with lint.I found the source was a hole in the vent tube outside the machine. I fixed that first . The lint had been sucked back into the machine. The first half hour was spent vacuuming out all the lint and then I could proceeded with the motor change. I followed the video exactly. I removed the screws at the two front corners, after lifting the top and controls and tying it... Read more

I took the dryer apart.....first had to clean out all the lint here and there. Took the drum out, inspected the belt and back support wheels. They seemed to be fine. In the front the drum turns on two supports that have a Teflon glide. Those two glides had been worn off with their pad so metal was rubbing against metal. Went online to appliancepartspros.com and looked up on the schematic what parts I needed. I also had called around locally and the same parts cost twice as much....so I... Read more

Found the parts in the diagram of my fridge and simply installed it very easy Read more

One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more

Overall the fix wasn't too hard. The challenge was putting the oven door back together and holding it together while trying to tighten the screws. Enlisted my wife's help to hold the door and at first the handle screws wouldn't tighten. My cordless screwdriver's battery was under-charged. Once I switched batteries I was able to tighten the screws. Seemed like I needed to push too hard (my wife freaked "not so hard you will strip them!") however pushing hard was what was needed. Both screws... Read more

• Timer will not advance
• Doesn't shut off

First off let me say thank you for having the part to me in 1 day. all it took were 5 screws and to lay the new timer next to the old one and exchange the wires from one to another. it was easier than making a peanut butter and jelly sandwich Read more

When I pulled out the dryer from the wall, I could see dust/lint had accumulated everywhere and the vent system was compromised. I vacuumed up the dust/lint accumulation outside and then inside the vent system. I then opened the lower cabinet to clean and check its condition. I removed the water steamer bottle and its sub-assembly and then the drum. After cleaning and inspecting components — both visually and with a multi-meter I determined the problem was the appliance doing what it was... Read more

I put the new motor pulley on and re-attached the belt. I watched a crap ton of YouTube videos and performed what the professionals did. I ate food before the repair so my body would perform as a top ranked athlete. I moved my body in multiple positions between sitting down and kneeling over. I used a soft towel for my knees when kneeling. I asked my wife to "hold this" while I attached the belt. I screamed, "Quit moving it!!!!! (The drum)," while I put the belt around the pulley. I left my... Read more