Thermador Dishwasher Parts

This was to address an E:09 fault code on a Bosch dishwasher. I swapped out the Circulation motor and heater assembly. The video given on APP.com was for a different model, but more or less the same. The video gave me confidence enough to order the part and attempt it. The significant difference was that in the video, the assembly is easily accessible from the bottom of the unit. On my unit, however, the bottom is a closed plastic pan that isn't easily removable, likely requiring removal of the... Read more

We replaced the black door seal gasket around the front of the dishwasher. The old black seal gasket had begun to deteriorate, every time it was touched black stuff would rub off onto hands and onto utensils in the upper basket. We wore some disposable gloves to remove the old seal to avoid getting the black stuff on our hands. Before entirely removing the old seal gasket we studied its placement to tell which way the new seal gasket should be placed. We didn’t want to place the seal gasket... Read more

I spent a lot of time taking apart and cleaning the drain pump and hoses in my Bosch dishwasher. I still got the error that the drain pump wasn't right. So, after doing some research, I learned that the motor might be done and that seemed to be the only solution. I serached for my part on APPs.com and found the part for about $43 ($50 by the time tax and shipping was added in). The part was ordered, shipped and was on my doorstep in two days. I followed the repair video instructions provided... Read more

Replaced both the Spray Arm and the Spray Arm Water Supply Tube. Highly recommend replacing base plate whenever the Spray Arm Water Supply Tube is replaced. Plastic tabs on the base plate hold those parts together and are likely to break (as seen on Appliance Parts Pros installation video!!!). I sensed tab weakness so just transferred parts needed from the new tube to the old tube and reinstalled the original tube / base plate assembly rather than risk breaking those plastic tabs. I should... Read more

• overflowing

After first thinking I had a leak under my sink (dripping into my workshop in the basement), I quickly traced the source back to my Bosch dishwasher. I removed the bottom kick plate (phillips screwdriver) and could see a continuous drip from the Water Inlet Valve. Easy to see because the Water Inlet Valve is mounted in front. I shut off the power to the dishwasher at my breaker box and turned off the water to the dishwasher. First, I easily disconnected the power clip at the back of the Water... Read more

We replaced the black door seal gasket around the front of the dishwasher. The old black seal gasket had begun to deteriorate, every time it was touched black stuff would rub off onto hands and onto utensils in the upper basket. We wore some disposable gloves to remove the old seal to avoid getting the black stuff on our hands. Before entirely removing the old seal gasket we studied its placement to tell which way the new seal gasket should be placed. We didn’t want to place the seal gasket... Read more

Popped on the new one, very easy Read more

Obtained a replacement hose from App Parts Pros. Was actually an easy fix. The old hose is detached from the housing by just pulling it out(there are no clamps) with the assist of a screwdriver for leverage. The new hose then plugs in. Voila! Read more

Ordered a new filter. Read more

I bought the door and bottom seal and was already to go. Appliance Pro got the parts to me in 2 days. I read an article that said if the spray arm holes are blocked that this could cause a wave in the dishwasher that could cause the water to fly up to the inlet used for drying and the water could run down between the front and inside door appearing to be a leak. I checked and my spray arms were indeed blocked. I pulled them out, cleaned them up, reinstalled, and low and behold that was appeared... Read more

I changed the control board (00498022) in the door of my Thermador dishwasher. Thermador, Bosch, and Siemens all use the same board for the indoor controls and display. This required a #15-star head driver to remove the screws. I used an impact wrench (set to a low torq setting) to speed things up. There are approximately 12 screws to remove. Two are long. The rest are short. Be careful to hold the door together as the last screws are removed. Everything comes apart easily and you do not... Read more

• lights flashing or blinking
• Will not drain

Dishwasher died after 1 year and two weeks after purchase! The Bosch tech arrived and recommended replacing the drain pump (as well as cleaning the filter in vinegar). Ordered pump from APPros and it arrived THE NEXT DAY! Took out old one.... installed new one... and it worked! The new pump fit perfectly. Read more

It finally gave E15 code, then after drying out the E15 code came back within 5 minutes of running. I dried out the base then I ran the dishwasher and observed water coming down the overflow chute after running only 5 minutes.There is a water inlet (clear water chamber on the side of the machine). It had some gunk inside that was stopping a black float shut-off from moving. I replaced the water inlet chamber. I also suspected the non return valve (also called a check valve). From the parts... Read more

• overflowing
• Noisy

Using instructions I obtained over the internet, I first removed the DW's bottom cover panels so I could look inside the DW (with a flashlight) while it was running. I had to put their dishwasher through several wash cycles before I could pinpoint the location of the leak. (The water appeared to be coming from above on the left side of the DW, near the top, rear of the DW's blue "Pressure Chamber." Thinking that the problem likely lay in either a malfunctioning Pressure Chamber or in a... Read more

The parts were to complete the install. Not a repair really. Although this was my first dishwasher install DIY. and thanks to the very fast and accurate parts delivery I was able to get everything done right the first time. Read more

• Will not dispense detergent

Process was a bit more complicated than the videos I had watched online. Had to remove both front panel and control panel to get to soap dispenser. Removed wires to soap dispenser and rinse aide dispenser. Removed wire "harness" around the top and right side of dispenser. Pried back the clips to allow dispenser to be pushed out. It was helpful to have another person to hold the door open at this point. Bent clips back and reinstalled everything. New part works great. Read more