Thermador Parts

A replacement spring hinge that helps support and counterbalance the appliance door for smooth opening and closing and proper alignment. Restores reliable door movement and reduces drop or slamming when the original spring is worn or broken. What it does:

• Provides counterbalance tension to help hold the door open and control closing motion
• Restores proper door alignment and prevents uneven closing or gaps
• Reduces sudden drops, slamming, or heavy-feeling doors caused by a weak or broken spring
• Works as the mechanical tension element within the hinge assembly to maintain normal door operation

• One spring hinge (single counterbalance spring)

• Install with power disconnected and door supported to prevent dropping or injury
• May require partial door removal or hinge access depending on appliance design
• Compare the new spring to the old part for correct orientation before installing
• If other hinge components show wear or damage, replace them at the same time for best performance

This griddle cover handle replaces a cracked, loose, or missing handle so you can safely lift and lower the griddle cover. It restores a secure grip and the cover's intended ease of use. What it does:

• Provides a stable grip for lifting and lowering the griddle cover
• Replaces broken, cracked, or worn handle that won't stay secure
• Helps prevent accidental drops or contact with hot surfaces while handling the cover
• Matches the original appearance and mounting location for a clean repair

• Turn off and disconnect power to the appliance before starting any work.
• Allow the griddle and surrounding surfaces to cool completely to avoid burns.
• Use basic hand tools; handle attaches at the cover's designated mounting points—do not force or modify the cover.
• Replace with OEM-specified fasteners.

This silicone adhesive-backed seal replaces a worn or damaged dishwasher door/tub perimeter gasket to restore a tight seal and reduce leaks and dampness around the door. Flexible silicone resists common household temperatures and moisture. What it does:

• Forms a watertight barrier around the dishwasher door/tub edge to help prevent leaks during cycles
• Adhesive backing allows the seal to stick in place for consistent contact and reduced movement
• Commonly used when the existing gasket is cracked, flattened, torn, or no longer sealing
• Helps reduce water pooling, floor damage, and poor wash performance caused by door leaks

• One silicone adhesive-backed seal (33.75 in.)

• Clean and dry the mounting surface thoroughly before applying to ensure proper adhesion
• Peel backing and press seal into place, working slowly to avoid gaps or twists
• Trim excess if necessary with a sharp utility knife; avoid stretching the gasket while installing

This radiant cooktop element replaces a failed dual-size burner to restore proper heating on compatible glass-ceramic ranges. It provides the inner and outer cooking zones in one dual-ring element for flexible cookware sizing. What it does:

• Heats cookware using the inner or outer cooking ring for small or large pots and pans
• Restores normal cooking when a burner won't heat or heats only on one ring
• Replaces cracked, visibly damaged, or non-responsive radiant elements
• Helps eliminate uneven heating or intermittent power to the cooktop zone

• One radiant cooktop element (dual-size 230/140 mm)

• Disconnect power at the breaker before servicing the cooktop to avoid shock
• Handle the glass-ceramic surface and element carefully to prevent cracking
• After installation, test the burner on low and high settings to confirm operation

This impeller is the rotating pump component that moves water through the appliance, restoring spray and circulation performance. Replacing a worn or damaged impeller helps resolve poor wash/rinse results and noisy pump operation. What it does:

• Drives water flow inside the pump housing to maintain proper spray and circulation.
• Can cause weak sprays, poor cleaning, or unusual pump noises when worn or broken.
• Fits the CW H98/HB style pump assembly and interfaces with the pump shaft and housing.
• Designed for direct OEM-fit replacement where this impeller is specified.

• Recommended for users comfortable disassembling pump housings; refer to your service manual for specific steps.
• Disconnect power and turn off the water supply before starting service.
• Inspect the pump housing, seals, and shaft for wear; replace any damaged components to prevent repeat failure.
• Use appropriate tools and handle plastic parts carefully to avoid cracking.

This lava rock basket holds and secures lava rocks used with compatible gas burner assemblies to support even heat distribution and protect the burner area. It replaces a worn, broken, or missing basket for safe operation. What it does:

• Holds lava rocks in place so they heat evenly for consistent burner performance
• Protects the burner tray from direct contact with lava rock and debris
• Helps prevent lava rocks from shifting or falling into the burner area
• Addresses symptoms such as loose or missing rock support, shifting lava rock, or unstable burner arrangement

• One lava rock basket assembly

• Turn off the gas supply and power to the appliance before servicing
• Use basic hand tools; verify correct fit and orientation before finalizing installation
• Dispose of damaged lava rocks and worn parts responsibly

This grill grate provides a stable, even cooking surface for compatible Bosch grills, restoring proper support and heat contact for pans and food. It replaces worn, bent, or missing grates to improve cooking consistency. What it does:

• Serves as the primary cooking surface, supporting cookware and food above the burner or heat source.
• Restores proper clearance and airflow for even heating when original grate is warped or damaged.
• Keeps food elevated and stable to prevent tipping or contact with burners.
• Foot provides extra stability and corrects alignment within the grill frame.

• One grill grate with attached foot

• Ensure the appliance is completely cool and gas/electric supply is turned off before handling.
• Typically installs as a drop-in replacement; align grate and foot with existing supports and seating points.
• Inspect surrounding seals and supports; replace any damaged mounting hardware for secure fit.
• Clean with non-abrasive cleaners; avoid harsh scrubbing that could remove coatings or finish.

This is the left hinge cap. For right hinge cap use 00165295.

This door latch cover is a direct-fit replacement trim piece that protects and conceals the dishwasher door latch assembly while restoring a finished appearance. Keeps the latch area tidy and helps ensure the door closes cleanly. What it does:

• Covers and protects the door latch mechanism from debris and wear
• Helps the door latch engage and the door sit flush when closed
• Restores the appliance's cosmetic finish around the latch area
• Can address symptoms such as a loose-looking latch area or an unsealed door edge

• Disconnect power to the appliance before installing; follow lockout/tagout practices
• Basic hand tools (screwdriver or trim tool) are typically required to remove the old cover
• Align the new cover over the latch assembly and snap or fasten into place per OEM diagram
• If the latch mechanism or strike is damaged, replace those parts as needed for full repair

A reed switch door sensor that detects when the appliance door is closed so the control can start cycles. Replaces a failed magnetic sensor to restore reliable door-closed detection and normal operation. What it does

• Acts as a magnetic contact that signals the control when the door or lid is closed
• Helps prevent the appliance from starting if the door is open or not fully latched
• Common symptom fix for no-start, intermittent cycle start, or control not recognizing a closed door
• Works as the electrical switching element in the door/detector assembly

• One reed switch (single replacement sensor)

• Disconnect power to the appliance before replacing the part to avoid shock or damage
• Handle the switch and wiring gently; avoid bending or stressing terminals and solder joints
• Locate and access the door/detector area per your service manual or tech sheet; confirm connector orientation before installing

This replacement inner oven door glass restores a clear viewing window and helps contain heat for safe, efficient baking. It fits into the oven door assembly to replace cracked, chipped, or cloudy glass. What it does:

• Restores a clear view into the oven cavity so you can monitor cooking without opening the door
• Helps seal the door to reduce heat loss and maintain consistent cooking temperatures
• Replaces cracked, shattered, or damaged inner glass that can compromise safety or appliance performance
• Matches OEM fit and form for a secure installation when used with the correct door hardware

• High-level job: remove the oven door, disassemble door panels to access inner glass; reassemble in reverse order
• Handle glass carefully and wear cut-resistant gloves and eye protection
• Inspect door seals and mounting clips during reassembly; replace any damaged hardware

This blue spark electrode wire connects the oven/range spark electrode to the ignition module so burners or the oven spark reliably. Replacing a damaged or frayed wire restores proper ignition and reduces intermittent or no-spark problems. What it does

• Carries the high-voltage spark from the ignition module to the electrode so the gas ignites.
• Commonly fixes symptoms like burners or oven not sparking, intermittent ignition, or visible wire damage.
• Helps prevent arcing and erratic ignition when the original wire is cracked, burnt, or corroded.
• Matches the OEM shape/color for proper routing and fit in compatible models.

• One blue spark electrode wire (single wire as shown)

• Disconnect power and shut off gas supply before starting any work; follow all safety precautions.
• Handle porcelain/ceramic electrode tips and insulation carefully to avoid damage.
• Route the wire along the original path and secure any retainers; avoid contact with hot surfaces.

This float switch lever is the actuator that moves the dishwasher's tub float to operate the water-level/flood-sensing switch, helping the appliance detect overfill and control fill/drain cycles. Replaces a worn or broken lever to restore proper float activation. What it does:

• Transfers movement from the tub float to the float switch so the machine senses water level correctly
• Commonly needed when a cracked or detached lever prevents the float from engaging the switch
• Can stop overfill-safety trips or no-fill symptoms caused by a non-responsive float assembly
• Works with the existing float and float switch; restores mechanical linkage function

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove lower access panels or tub components as required to reach the float assembly
• Inspect surrounding clips and the float for damage; replace any broken hardware
• Tighten securely but avoid over-torquing; test float movement and switch activation before reassembly

This tubing assembly routes water inside the refrigerator to the dispenser/ice system, restoring a sealed water path and reliable flow. Use it to replace cracked, kinked, or leaking tubing for better water delivery. What it does:

• Carries water from the inlet to the dispenser/ice components to enable ice and water dispensing
• Stops leaks and seepage caused by cracked or damaged tubing
• Restores proper water routing when bends or kinks restrict flow

• Tubing assembly

• Turn off the refrigerator and shut off the water supply before starting work
• Drain any remaining water from lines and have a towel/container ready for spills
• Inspect connections and use new fittings or seals if the old ones are damaged

The Bracket, Motor Mounting is an OEM part for Bosch range hoods. It is responsible for securely mounting the internal motor and fan assembly within the range hood structure. The motor mounting bracket provides a sturdy foundation that isolates vibrations and minimizes noise transfer during operation.

Causes of a bad bracket can include cracks, breaks, or detachment from normal wear and tear over time or failure from repeated exposure to motor vibrations.

Symptoms of a bad bracket include:

• Loosening or detachment of the internal motor/fan assembly
• Increase in noise levels and vibration transfer to surrounding cabinets
• Instability or shifting of the motor during range hood operation
• Possible interference or contact between moving components

Replacing with this OEM Bosch bracket restores the proper mounting and isolation of drivetrain components, ensuring smooth, reliable performance. This part is also compatible with Thermador, Gaggenau, and some Kenmore branded range hood models.