Thermador Parts

A replacement pilot light indicator that notifies you when a range or cooktop burner circuit is energized. Restores a visible indication so you can quickly tell whether the appliance control is active. What it does:

• Illuminates when the burner or control circuit is powered to indicate an active state
• Helps diagnose control or power issues by showing whether voltage reaches the control panel
• Common symptom: no light on the control panel or indicator despite a burner selected
• Safe, low-voltage indicator used on select Bosch ranges and cooktops

• One pilot light indicator as shown

• Disconnect power to the appliance before attempting any service to avoid shock
• Access may require removing the control panel or trim
• Handle with care to avoid damaging the lens or terminals

This air interlock is the airflow switch that helps monitor and control dryer vent airflow, ensuring the appliance only runs when proper air movement is detected. It replaces a worn or failed interlock to restore normal vent sensing. What it does:

• Senses airflow through the vent and signals the control system to allow or stop operation
• Prevents dryer from starting or continuing a cycle when airflow is restricted
• Common symptom: dryer fails to start, stops mid-cycle, or shows poor drying performance
• Can help address intermittent operation caused by a faulty vent sensing switch

• Disconnect power before servicing to avoid electrical shock
• Handle the switch and wiring gently; verify connector orientation before reinstalling
• Confirm venting is clear and intact when replacing this part

This 65-inch door gasket seals the appliance door to help maintain proper temperature and prevent leaks. It replaces a worn or torn gasket to restore a tight seal and improve efficiency. What it does:

• Creates an airtight seal around the door to help prevent water leaks and air loss
• Helps maintain consistent internal temperature and protect contents
• Reduces drafts and minimizes moisture buildup that can cause odor or frost
• Common symptom: visible cracks, tears, flattening, or water leaking from the door

• Install on a clean, dry door surface; follow OEM alignment to ensure an even seal
• Inspect door frame and mounting channel for damage before installing the new gasket
• Gasket may need gentle warming or seating to fit snugly in the channel (avoid open flame)
• Disconnect power/water if removing door panels or working near electrical components

This 1/4" gas supply tubing connects the appliance's gas line to the valve, providing a secure path for fuel so the unit can ignite and operate safely. Use when tubing is damaged, leaking, or replaced during valve service. What it does:

• Channels natural gas/LP from the household supply to the appliance valve
• Replaces cracked, corroded, or bent tubing that can cause leaks
• Helps stop symptoms like a persistent gas smell, failure to ignite, or intermittent burner operation
• Works with the appliance's inlet and control valve fittings to maintain proper gas flow

• Turn off the gas supply and electrical power before starting work
• Use approved fittings, thread sealant rated for gas, and test all connections for leaks after installation
• Do not modify or reuse damaged tubing; replace with exact-fit parts

This push-button switch controls electrical power or function circuits in compatible Bosch appliances, restoring user input and on/off control when the original switch fails. What it does:

• Opens or closes the appliance's electrical circuit when pressed to enable a given function
• Commonly used where a user-operated control needs a durable, tactile interface
• Resolves symptoms like an unresponsive control panel, intermittent operation, or functions that won't toggle on
• Replaces a worn or non-clicking switch to restore reliable button response

• One replacement push-button switch

• Disconnect power to the appliance before servicing to prevent shock
• Verify correct terminal connections and orientation before final assembly
• Use basic hand tools; avoid forcing connectors to prevent damage

This actuator lever assembly with springs replaces a worn or broken control lever to restore proper mechanical movement in the appliance. It helps the dispenser/latch mechanism operate smoothly for reliable everyday use. What it does:

• Transfers motion from a control cam or motor to the latch or dispenser linkage
• Restores proper engagement when a broken or fatigued lever prevents operation
• Helps stop intermittent or failed cycle starts caused by damaged mechanical linkage
• Works as a direct-fit replacement that re-establishes spring tension and lever action

• Disconnect power before accessing internal components to avoid shock or injury
• Basic hand tools usually required; maintain original screw/hardware if reusing
• Inspect surrounding linkages and replace damaged clips or fasteners as needed

A small spring-style hose clamp used to secure flexible appliance hoses to fittings and prevent leaks. Simple, durable replacement that restores a tight connection for water and drain lines. What it does:

• Compresses around a hose to hold it firmly on an inlet, outlet or drain fitting
• Helps stop leaks caused by loose or slipping hoses
• Keeps hoses seated during normal appliance operation and vibration
• Commonly used on dishwasher and washer drain or water hoses

• One hose clip / spring clamp

• Disconnect power and water supply before starting repairs
• Use pliers to expand the clamp for removal and reinstall; ensure hose is fully seated before releasing clamp
• Inspect the hose and fitting for damage; replace any cracked or brittle hose
• Do not overtighten or deform clamp when installing; replace if corroded or weakened

A replacement spring hinge that helps support and counterbalance the appliance door for smooth opening and closing and proper alignment. Restores reliable door movement and reduces drop or slamming when the original spring is worn or broken. What it does:

• Provides counterbalance tension to help hold the door open and control closing motion
• Restores proper door alignment and prevents uneven closing or gaps
• Reduces sudden drops, slamming, or heavy-feeling doors caused by a weak or broken spring
• Works as the mechanical tension element within the hinge assembly to maintain normal door operation

• One spring hinge (single counterbalance spring)

• Install with power disconnected and door supported to prevent dropping or injury
• May require partial door removal or hinge access depending on appliance design
• Compare the new spring to the old part for correct orientation before installing
• If other hinge components show wear or damage, replace them at the same time for best performance

This griddle cover handle replaces a cracked, loose, or missing handle so you can safely lift and lower the griddle cover. It restores a secure grip and the cover's intended ease of use. What it does:

• Provides a stable grip for lifting and lowering the griddle cover
• Replaces broken, cracked, or worn handle that won't stay secure
• Helps prevent accidental drops or contact with hot surfaces while handling the cover
• Matches the original appearance and mounting location for a clean repair

• Turn off and disconnect power to the appliance before starting any work.
• Allow the griddle and surrounding surfaces to cool completely to avoid burns.
• Use basic hand tools; handle attaches at the cover's designated mounting points—do not force or modify the cover.
• Replace with OEM-specified fasteners.

This silicone adhesive-backed seal replaces a worn or damaged dishwasher door/tub perimeter gasket to restore a tight seal and reduce leaks and dampness around the door. Flexible silicone resists common household temperatures and moisture. What it does:

• Forms a watertight barrier around the dishwasher door/tub edge to help prevent leaks during cycles
• Adhesive backing allows the seal to stick in place for consistent contact and reduced movement
• Commonly used when the existing gasket is cracked, flattened, torn, or no longer sealing
• Helps reduce water pooling, floor damage, and poor wash performance caused by door leaks

• One silicone adhesive-backed seal (33.75 in.)

• Clean and dry the mounting surface thoroughly before applying to ensure proper adhesion
• Peel backing and press seal into place, working slowly to avoid gaps or twists
• Trim excess if necessary with a sharp utility knife; avoid stretching the gasket while installing

Support, hinge counter restores proper hinge support and door balance for a worn or damaged hinge assembly. This replacement helps the appliance door open and close smoothly and stay aligned for reliable everyday use. What it does:

• Provides structural support to the door hinge and helps counterbalance the door
• Stabilizes hinge movement to reduce sagging, binding, or uneven closing
• Helps the door latch and seal correctly by keeping the hinge alignment consistent
• Use when you notice door droop, difficulty latching, or irregular door motion

• Installation may require partial disassembly of the door or hinge assembly—refer to the OEM instructions for your model
• Disconnect power and turn off water supply before beginning any repair
• Inspect surrounding hinge components and fasteners; replace any damaged parts and test door operation after installation

This radiant cooktop element replaces a failed dual-size burner to restore proper heating on compatible glass-ceramic ranges. It provides the inner and outer cooking zones in one dual-ring element for flexible cookware sizing. What it does:

• Heats cookware using the inner or outer cooking ring for small or large pots and pans
• Restores normal cooking when a burner won't heat or heats only on one ring
• Replaces cracked, visibly damaged, or non-responsive radiant elements
• Helps eliminate uneven heating or intermittent power to the cooktop zone

• One radiant cooktop element (dual-size 230/140 mm)

• Disconnect power at the breaker before servicing the cooktop to avoid shock
• Handle the glass-ceramic surface and element carefully to prevent cracking
• After installation, test the burner on low and high settings to confirm operation

This impeller is the rotating pump component that moves water through the appliance, restoring spray and circulation performance. Replacing a worn or damaged impeller helps resolve poor wash/rinse results and noisy pump operation. What it does:

• Drives water flow inside the pump housing to maintain proper spray and circulation.
• Can cause weak sprays, poor cleaning, or unusual pump noises when worn or broken.
• Fits the CW H98/HB style pump assembly and interfaces with the pump shaft and housing.
• Designed for direct OEM-fit replacement where this impeller is specified.

• Recommended for users comfortable disassembling pump housings; refer to your service manual for specific steps.
• Disconnect power and turn off the water supply before starting service.
• Inspect the pump housing, seals, and shaft for wear; replace any damaged components to prevent repeat failure.
• Use appropriate tools and handle plastic parts carefully to avoid cracking.

This lava rock basket holds and secures lava rocks used with compatible gas burner assemblies to support even heat distribution and protect the burner area. It replaces a worn, broken, or missing basket for safe operation. What it does:

• Holds lava rocks in place so they heat evenly for consistent burner performance
• Protects the burner tray from direct contact with lava rock and debris
• Helps prevent lava rocks from shifting or falling into the burner area
• Addresses symptoms such as loose or missing rock support, shifting lava rock, or unstable burner arrangement

• One lava rock basket assembly

• Turn off the gas supply and power to the appliance before servicing
• Use basic hand tools; verify correct fit and orientation before finalizing installation
• Dispose of damaged lava rocks and worn parts responsibly

This grill grate provides a stable, even cooking surface for compatible Bosch grills, restoring proper support and heat contact for pans and food. It replaces worn, bent, or missing grates to improve cooking consistency. What it does:

• Serves as the primary cooking surface, supporting cookware and food above the burner or heat source.
• Restores proper clearance and airflow for even heating when original grate is warped or damaged.
• Keeps food elevated and stable to prevent tipping or contact with burners.
• Foot provides extra stability and corrects alignment within the grill frame.

• One grill grate with attached foot

• Ensure the appliance is completely cool and gas/electric supply is turned off before handling.
• Typically installs as a drop-in replacement; align grate and foot with existing supports and seating points.
• Inspect surrounding seals and supports; replace any damaged mounting hardware for secure fit.
• Clean with non-abrasive cleaners; avoid harsh scrubbing that could remove coatings or finish.