Wall Oven Burner & Related Parts

This small surface burner assembly replaces a worn or damaged top burner on your gas range or cooktop, restoring quick ignition and an even flame so the small burner heats predictably for simmering and everyday cooking.

• Distributes gas through the burner ports to create a steady, controllable flame at the small-burner position
• Works with the igniter/orifice holder to light reliably
• Common symptoms: burner won't light or only clicks, weak or uneven flame, yellow tips, delayed ignition, or flame that sputters out
• Visible cracks, warping, or heavy corrosion on the burner head

• Shut off gas supply and power; allow the cooktop to cool completely before servicing
• Remove grate and cap, then take out the old burner assembly; retain any screws or brackets as required by your model
• Align the new assembly over the orifice and igniter; seat fully and secure per the manufacturer's instructions
• Restore gas and power, then check for proper ignition and flame; verify there are no gas leaks

Replacement surface burner for gas range cooktops. Installs directly onto the burner base. Order when your existing burner is cracked, clogged, or missing.

This is a black burner cap that sits on top of a gas range surface burner head. It distributes the gas flame evenly around the burner for consistent heating. Replace this cap if it is cracked, chipped, warped, or heavily corroded, which can cause uneven flames, poor ignition, or yellow/orange flame color.

Burner cap for gas range cooktops. Distributes flame evenly over the burner. Replace if cracked, chipped, worn, discolored, or missing.

Burner cap sits on top of the gas burner head to shape the flame and shield it from spills. Replace if cracked, broken, worn, or missing.

Surface burner cap sits on top of the gas burner head to shape the flame. Replace if yours is missing, chipped, cracked, or warped for proper appearance.

Natural gas burner orifice meters gas flow to range burners. Replace worn or clogged orifices for stable flame. Used for LP to natural gas conversions.

The Burner Valve is an OEM component specifically designed for Frigidaire ranges. It controls gas flow to individual burners, providing a selection of different heat levels when operating the cooktop.

Causes of a bad burner valve can include wear over extended usage periods, damage from water, or gas blockage impeding operation. 

Symptoms of a bad burner valve include:

• Inability to light specific burners or adjust the flame height
• Uneven or intermittent burner performance  
• Gas leaks at burner valve connections
• Recurring error codes due to valve malfunctions

Replacing with this OEM valve restores full functionality to the range cooktop. Compatible with existing gas lines, it supports safe and reliable cooking performance.

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace before issues worsen.
 

This valve-to-regulator tube carries fuel between the pressure regulator and gas control valve, maintaining a sealed path for proper ignition and stable flame. Replace if the tube is kinked, damaged, or leaking.

• Provides a rigid, factory-formed connection between the pressure regulator and valve
• Helps ensure correct gas flow to the burner system
• Failure signs include weak or no flame, delayed ignition, repeated clicking, or a gas odor
• Visible kinks, corrosion, or stripped fittings indicate the tube should be replaced

• Disconnect power and shut off the gas supply; ventilate the area before servicing
• Use two wrenches to back up fittings; avoid twisting the regulator or valve bodies
• Route the tube without kinks and tighten flare connections securely
• Leak-test all joints with an approved solution—never an open flame—before restoring service.

Controls gas flow to your range's top burner. Replace if the valve stem breaks, knob won't turn, or gas won't adjust properly for simmering or boiling.

Replaces a damaged, missing, or incorrect LP bake burner orifice in gas ranges. Essential for propane conversion to meter gas properly to the oven.

Distributes gas through ports to create an even cooking flame. Replace if cracked, clogged, or worn to restore proper ignition and consistent heat output.

Secures the gas orifice and aligns it with the burner assembly on your gas range. Replace if cracked, damaged, or missing to restore proper gas flow path.

The surface burner orifice holder is a brass or metal fitting that threads into the gas valve and holds the orifice, which is the small precisely sized opening that controls how much gas flows to a cooktop burner. Together with the orifice, it regulates flame size and ensures proper combustion. Replace this part if a burner produces an uneven, weak, or oversized flame, or if the holder is damaged, corroded, or leaking gas at the burner connection.

Black burner caps sit atop gas range burner heads to shape the flame. Replace cracked, worn, or missing caps to restore even cooking and a clean look.

Controls and stabilizes incoming gas supply to burners and oven. Replace if regulator is cracked, leaking, or fails to maintain consistent gas pressure.