Wall Oven Parts

• Won't start

Removed and replaced 3 door switches and mounting bar that holds switches plastic gets brittle with age and each switch comes out slightly different from each other, the chances of breaking a mounting pin is very easy. care should be taken when snapping mounting bar back into place to insure top latch and bottom latch locate properly insure bar is proper aligned when tightening screws their is free play in mounting bracket that could affect door properly engaging switches. NOTE that their are... Read more

• Little to no heat when baking
• Element will not heat

I wanted to get the upper oven baking element replaced; it hasn't been working for a few months. This double oven has had two other issues, there is a fan that comes on to cool the electronics panel, That fan has made excessive noise and it operates for 2-3 hours after the oven turns off. The other problem with the oven is the Self-Cleaning feature runs for about 15-30 minutes and then turns off with an error code. I've had a local appliance repair person in to address the error code and... Read more

Ordered new seal pulled old one off and put new one in its place Read more

• Gas igniter glows, but will not light
• Won't start

After 5 igniter replacements, I've gotten pretty good at this. Less than 30 minutes start to finish -- including mopping under the range, etc. You need one hex driver for the whole job -- 3/8" I believe. 1. Remove all of the racks and the oven door. Remove the bottom panel inside the oven. Now unscrew the flame cover (4 hex screws), remove, and unscrew the old igniter (2 hex screws). 2. Pull the oven away from the wall. Be careful not to kink the gas line. Unplug the range. Remove... Read more

Replaced element. The new element was perfect. The shipping was perfect. Installation would have taken less than 10 minutes if the two range wires attaching to element had been 1 inch longer. Attached thin nosed vice grips to wires at spade terminals to facilitate attachment to element. The repair was simple enough but it would have been perfect if GE engineers had made wires 1 inch longer. Read more

Replacing head burner d solved the problem. The 8 year old original developed a mild warp, replacing it was the solution. GE gas cook top Model JGP933SEK1SS. I replaced the other burner caps for a cosmetic renewal. Read more

We are very inexperienced appliance repair people. Thus check it out first to see if we can fixit...successs. First checked to be sure it wasn't the actual switch. Did this by numbering the wires and then switching the two switches b/w the right and left front dual burners. Success, the switch was fine but kinda disappointed cause this part was less expensive. Proceeded to then order the left front dual burner. Arrived in a few days, packed well. We unplugged the appliance, as it been a... Read more

Replaced the burner. Read more

Ordered all the parts Read more

• Little to no heat when broiling
• Element will not heat

Once I received the element within three days, I simply removed the other element by unclipping and unplugging lugs in rear. Placed the new one in clips and connected lugs and all was good! Read more

• Oven is too hot
• Won't start
• Little to no heat when baking

Spoke to a parts pro and told them of the problem. there were 2 possibilieies from the explanation of what the parts do. onw could have been the Range oven igniter. that wasn't it beaacause the over was lighting fine. by process of illimination it was the Oven Sensor Assembly. Read more

I first felt along each heating element (bake and broil) hoping to find a rough or blistered place on them. But they were both smooth with no irregular places. (replacing the elements would have been the easiest and cheapest repair. Pulled the back off the range (unplugged, of course) - checked wiring. There were no loose connections or burned wiring. I disconnected the elements and checked them with a ohmmeter (VOM) and both had continuity. Discovered that both elements used the same... Read more

I ordered this glass and used a youtube video to replace the shattered glass step-by-step. I was a bit wary of doing this work myself, but it proved to be a snap. Within an hour of finding this package on my front porch, I had the oven as good as new. Read more

Replacing head burner d solved the problem. The 8 year old original developed a mild warp, replacing it was the solution. GE gas cook top Model JGP933SEK1SS. I replaced the other burner caps for a cosmetic renewal. Read more

• Won't start

The full story: Dishwasher stopped running mid-cycle. When I first began troubleshooting I tried manually advancing the timer knob, and the machine would run. That led me to believe that the actual timer assembly was bad, so I replaced it. The dishwasher ran fine for a day, and then the same problem came back. This time, however, I also had to push in on the door to get it to run. I looked around online, and someone suggested that the door latch wasn't closing tightly enough. I adjusted the... Read more

Went to the AppliancePart Pros website, found the OEM replacement parts and at a price that was better than any of the other sites I had looked into. Ordered the parts and they arrived within 2 days. Excellent service. Read more