White Westinghouse Washer Parts

Simply open the top of the washer by inserting a putty knife (watch YouTube ) and then the front panel by removing two bottom philips head screws on the front. The whole front panel comes right off. Using pliers the spring clams holding each hose, they come off and each hose is replaced. The drain one was only leaking but since it has open I changed both and even the drive belt. Whole job less than 1 hour. BTW parts arrived next day! Read more

After first doing a Google/YouTube search, There was only one "hit" on my search results. Next I went to an appliance message board forum but after almost a week and more than a dozen views, no response was received. This is unusual. I've been on this board before with positive results. They also changed the "rules" for DIYers which could explain why I didn't have a lot of response from the experts. I attempted to get the unit into diagnostics mode. I was unable to clear the E90 "general... Read more

• Won't start

This is an easy fix, but Appliance Parts Pros make finding the correct part easy. I looked at many sites to get a new knob, as I was tired of using pliers to start the dryer. The images on the grid are worth their weight in gold! Read more

Our washing machine door boot seal was getting moldy and causing odor problems. Cleaning tablets and bleach weren't helping so it was time to be replaced. While I had the top and front off I changed all the hoses that could be collecting soap scum and mold, all other wetted parts were removed and washed. The video on the door boot seal, and inlet valve assembly were extremely helpful in understanding how these parts are removed and reassembled. Although the door boot seal is the most visible... Read more

The seal at the bottom of the tub had started to fail. On large loads water would leak so I ordered a new one rubber seal. Getting the trunnion off the transmission shaft was hard as it was calcified and corroded. I used a wire brush to get some of it off and then used a lot of WD-40. The bolt holding the trunnion plate on sheared off when I tried to remove it on one side and the other came out ok (the bolt hole through the trunnion is not threaded so it should slide out once the plate is off... Read more

New hose and clamp. Read more

Removed old baffle. Had to cut it out with a multi-purpose tool. Replaced with new one. Job was not too bad, and only took about 15-20 minutes. The best part was the fast delivery time for the part. Ordered the PM of one day, and had it in the early morning of the next day. (OUTSTANDING!!!) Read more

Watched a few of your videos and ordered the springs and a insert, and actually got the parts right. I am not a Appliance repair guy but I am retired and I am pretty handy so I thought what the heck. I watched the videos, a lot of common sense, common tools, and plenty of time. My knuckles are busted up and a little blood, but I got it done. Was actually kind of rewarding. Works like a champ. The Videos, ARE AWESOME. Read more

Ordered a shipping support kit from AppliancePartsPro.com, got it shipped next day, and installed the kit in less than 5 minutes to prep front loading washer for immediate moving. Read more

The E32 diagnostic code that the Frigidaire washer was throwing after a quick water fill attempt was not in the supplied Data Sheet that came with the washer and Frigidaire would not provide and updated Data Sheet because, "it's a liabiliity issue" was their statement, but they did tell me that the problem was in the Fill Pressure Sensor/Wire Harness or the Main Control Board (the display board). I ordered the Pressure Sensor and Main Control Board from AppliancePartsPros after checking... Read more

Three new vanes. Installation was easy, removed one stainless screw on each vane, slid the broken vanes toward the front of the machine, compressed the old vane slightly and came right out. They have to be slid about 1 to 2 inches forward for removal. This was an easy fix. Read more

The repair guy told me if I have him fix it I should just buy a new one. I like my washer and dryer because it's a combo and takes up little space so I decided to fix it myself. Not sure if I got lucky but appliance parts pros had a video with almost my exact washer which made repair very easy. Read more

SELF REPAIR, WITH A VIDEO EXAMPLE. Read more

Like the original. Read more

Found the correct part number, ordered a replacement and replaced it Read more

Purchased the door panels (both sides) and replaced them both. Not sure if spending $150 on door parts for a 15 year old washer was a great investment, but the parts worked great. Took maybe five minutes to put it all back together. Read more