Whirlpool Blower Wheel Or Fan Blade

This replacement fan blade mounts to the fan motor to move air through the system, restoring proper airflow and helping maintain stable temperatures while reducing unwanted noise and vibration. What it does:

• Attaches to the fan motor shaft to circulate air through the appliance
• Drives airflow across coils and compartments to support proper cooling
• Helps maintain even temperatures and stable performance
• Common symptoms include rattling/whirring noises, weak airflow, warm spots, or wobbling due to a cracked or warped blade

• Disconnect power before servicing
• Access the fan housing; remove any guards/shrouds as needed
• Transfer and reuse the existing retainer/clip or fastener and fully seat the blade on the motor shaft with correct orientation
• Spin by hand to ensure free clearance; reassemble and test for smooth, quiet operation

This is the fan blade that attaches to the condenser fan motor, typically located near the bottom rear of the refrigerator. It draws air across the condenser coils to dissipate heat and keep the refrigerator running efficiently. Replace this blade if it is cracked, warped, or broken, which can cause loud noises, reduced cooling performance, or the compressor overheating.

The Fan Blade is an OEM part for Whirlpool refrigerators. It helps cool down the condenser coils by drawing air over them, providing cooling and temperature regulation inside the refrigerator.

A bad fan blade can be caused by wear and tear, damage from debris or foreign objects, or motor malfunctions. If you notice issues such as poor cooling performance, unusual noises coming from the refrigerator, or the fan not spinning properly, it may indicate a problem with the fan blade.

Symptoms of a bad fan blade include:

• Inadequate cooling or temperature fluctuations 
• Unusual noises coming from the refrigerator
• The fan not spinning or spinning slowly

Replace your faulty fan blade with this genuine OEM part to restore your refrigerator. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

Instruction sheet included.

This blower housing assembly replaces the blower chamber that supports the blower wheel and routes air through the dryer for proper tumbling and drying. Restores correct airflow and helps reduce overheating or poor drying performance. What it does:

• Houses and supports the blower wheel to direct airflow from the drum to the exhaust.
• Ensures proper airflow for consistent drying and venting.
• Can address symptoms like weak airflow, long dry times, or unusual blower noise when damaged or cracked.
• Works with the blower wheel and motor to maintain lint passage and exhaust flow.

• Disconnect power before inspecting or replacing the blower housing; follow manufacturer safety procedures.
• Access may require removing the dryer front or rear panel depending on model.
• Inspect the blower wheel and motor for damage or obstructions while replacing the housing.

If your dryer takes too long or overheats, a worn blower wheel may be reducing airflow. This assembly restores proper air circulation through the drum.

This blower wheel attaches to the motor shaft inside the dryer and draws heated air through the drum and out the exhaust vent. It is typically made of plastic or composite material with angled fins designed to create strong airflow. Replace this part if the dryer takes too long to dry clothes, makes squealing or rattling noises, or produces weak airflow at the exhaust vent.

This is a plastic fan blade that attaches to the ventilation motor inside the microwave. It circulates air to cool internal components and, in over-the-range models, helps vent steam and cooking odors. Replace this blade if it is cracked, broken, or wobbling, which can cause excessive noise or reduced ventilation performance.

This replacement blade-fan moves air inside the appliance to help maintain proper temperature and prevent ice buildup. It restores airflow so the appliance can cool and cycle as designed. What it does

• Circulates air over coils and compartments to support even cooling
• Helps prevent frost accumulation and hot spots caused by poor airflow
• Commonly replaced when airflow is weak or the fan is noisy or damaged
• Works with the original fan motor hub to spin smoothly and efficiently

• One blade-fan

• Disconnect power before beginning any repair to avoid electrical shock
• Handle the fan blades carefully to avoid bending; a warped blade can vibrate or rub
• Inspect the fan hub and motor before installation; replace damaged mounting hardware as needed

This is a fan blade that attaches to the motor shaft inside the microwave to circulate air for cooling internal components. It helps prevent the magnetron and other electronics from overheating during operation. Replace this blade if it is cracked, broken, or warped, or if the microwave is running louder than normal or overheating during use.

Freezer not cooling evenly or running warm? This evaporator fan blade circulates cold air throughout your refrigerator. Simple press-on installation.

Fixes uneven heating in your microwave. This stirrer blade distributes microwave energy evenly. Simple 10-minute repair restores proper cooking.

This stirrer fan disk is the replacement disk that mounts to the microwave stirrer/fan assembly to help distribute microwave energy and airflow for more even cooking. Durable OEM-style fit for straightforward replacement. What it does:

• Spins with the stirrer/fan assembly to help diffuse microwave energy for more even heating
• Helps direct airflow from the stirrer fan to reduce hotspots and improve cooking consistency
• Worn, cracked, or broken disks can cause uneven cooking, rattling, or noise from the stirrer area
• Designed to match OEM form and fit for reliable performance

• One stirrer fan disk

• Disconnect power before servicing; follow microwave service safety procedures
• Access requires removing the microwave's rear/upper cover — keep fasteners and shielding in a safe place
• Align and secure the disk to the stirrer/fan hub per OEM diagram; do not force or overtighten
• If you see additional damage to the stirrer motor or housing, replace those components as needed