Whirlpool Clip Or Clamp

This console clip secures the appliance control console or control panel to the cabinet, restoring a snug, stable fit and stopping rattles or loose movement. Durable plastic clip designed to replace a broken or worn fastener. What it does:

• Holds the control console in place to prevent sagging or separation from the cabinet
• Stops rattling or vibration noise caused by a loose console
• Restores proper alignment for buttons and switches on the control panel
• Replaces a cracked, worn, or missing mounting clip

• One console mounting clip (1 each)

• Disconnect power before attempting any service to avoid shock or injury
• Remove the console or access panel per your model's service instructions to reach the clip
• Pry out the damaged clip carefully and snap the new clip into the factory mounting boss until it seats
• Handle plastic parts gently to avoid cracking; before reassembling

This band is a replacement drum drive band that helps transfer motor power to the dryer drum for proper tumbling and rotation, restoring normal drying performance and reducing rubbing or slipping. What it does:

• Wraps around the drum to provide a friction surface for the drive motor to turn the drum
• Helps maintain consistent drum rotation for even drying
• Can reduce slipping, squealing, or intermittent tumbling when worn
• Supports smooth operation and prevents excessive wear on related drive parts

• One replacement band

• Disconnect power before beginning
• Inspect drum, idler, and motor for wear while replacing the band
• Use proper routing and tension per the appliance's service diagram to avoid slipping
• Do not overtighten; ensure secure seating before testing operation

This clip is a small retainer used to secure panels, wiring, or hoses so components stay in place and operate quietly. It prevents loose parts from shifting during normal use and helps maintain appliance fit and finish. What it does:

• Holds wiring, harnesses, or small hoses in position to prevent rubbing or disconnection
• Keeps trim or access panels seated to reduce vibration and noise
• Helps maintain correct routing to avoid wear on wires and hoses
• Commonly replaced when the original clip is broken, cracked, or missing

• One clip

• Disconnect power to the appliance before attempting any repair
• Access the area and remove any panels or covers that block the clip location
• Press the clip into its mounting slot or snap the harness into the clip until it seats securely
• Replace any damaged surrounding fasteners or retainers; do not use damaged clips

This clamp secures a flexible appliance hose or tube to prevent leaks and keep connections tight. It restores proper hose seating so water or air flows where it should, reducing drift and seepage. What it does:

• Fastens a hose or tube to a barb, fitting, or pipe to maintain a sealed connection
• Prevents hose slippage that can cause leaks or reduced performance
• Helps stabilize hoses that vibrate or move during normal appliance cycles
• Commonly used on water, drain, or vent hoses in laundry and kitchen appliances

• One clamp

• Turn off and unplug the appliance and shut off water supply before starting
• Use appropriate pliers or a screwdriver for the clamp type; avoid crushing the hose
• Inspect hose and fitting for damage and replace if needed

This spring-style hose clamp secures flexible appliance hoses to fittings, preventing leaks and keeping connections tight during operation. It's a small but critical fastener for reliable fluid containment. What it does:

• Holds a rubber or plastic hose firmly to a barb or nipple to stop leaks
• Keeps drain, inlet, or recirculation hoses seated under pressure and vibration
• Helps prevent water damage and performance issues caused by loose hose connections

• Use pliers or a clamp tool to expand the spring clamp and slide it into position; release slowly to seat
• Inspect hose and fitting for damage and replace if cracked or worn before installing the clamp
• Disconnect power and water and follow appliance safety procedures before servicing

This small retaining clip secures internal trim, panels, or wiring runs to keep components in place and prevent rattles or loose connections. It restores proper fit and helps maintain safe, quiet operation. What it does:

• Holds panels, trim pieces, or wiring harnesses in position to prevent movement
• Stops rattling and wear from vibration or loose parts
• Helps maintain correct alignment of surrounding components
• Useful when replacing damaged or missing fasteners during repairs

• Disconnect power to the appliance before starting any repair
• Access may require removal of trim, panels, or other parts; retain screws and fasteners
• Clip installs by snapping into a mating hole or channel; avoid forcing to prevent breakage
• Use appropriate-size trim tools to avoid scratching surrounding surfaces