Whirlpool Cooktop Parts

• Little to no heat when baking
• Oven not heating evenly
• Element will not heat
• Oven is too hot

I finally found the right serial number and found the part at Appliance Parts Pros. I was skeptical that they would send the element that had the correct rear brace fixture. when it came 2 days later i opened the box the Part was correct and it took about 15 minutes to replace since there are only two screws. My oven works fine now. THX Read more

On my Jenn-Air downdraft range, the oven stopped heating. The broiler still worked. So pulled the pan off the bottom so I could see and found the igniter wasn't glowing to start the gas. I had replaced the full electronic control panel using Appliance Parts Pros so knew they had the full breakdown of parts for my model. I found the igniter and ordered. But frankly, I wasn't sure about doing the repair myself. It looked easy enough from videos and discussions here. Still, dealing with the... Read more

I replaced the Oven Igniter. After ensuring that it was the igniter, by turning on the stove and taking out the oven bottom. Watch if it turns red. If not, then either the wiring is faulty, or the igniter went bad. The bulb was due to a loose and broken light bulb, can't use any normal bulb, these ones are specially made to withstand the heat. And the oven bottom was warped due repeatedly heating up and cooling down over the years. It took a fair bit of time to get the new one in, since it was... Read more

• Oven not heating evenly
• Little to no heat when baking
• Element will not heat

I googled the model number of the oven and came across AppliancePartsPros.com The coil along with replacing video was right at hand. I ordered the part, got it three days later (standard shipping) and installed it. To sum it up, it was a five minute job. Read more

• Won't start

There are hex screws keeping the igniter in place. I think they were 5/16...so you have to have a socket wrench. The space is kind of tight, and it's all on the right side, so if you're left handed (like I am) it's going to be a challenge to get the hex screws out without dropping them. Dropping them isn't too bad if they don't fall into the hole the gas pipe is coming through. Unfortunately one of them fell in there, and there's no getting it out of there. I had a machine screw that fit, so I... Read more

• Element will not heat

Personally I have experience working with electricity and knowing if I bought the part required this would be an easy fix. I got my model number and contacted Appliance Parts Pros and placed my order for the new elements, terminal blocks, and for appearance purposes 4 new Drip Pans. Excellent service and quick shipping. I ordered my parts on Sunday and received them on Tuesday. This was a simple repair that only required a screwdriver to remove the old terminal block from the range hood, wire... Read more

• Element will not heat

I lucked out my nephew was here to deer hunt and he helped me. I do believe I could have done it on my own but was more confident with his help. I will say the videos did help. Read more

Originally the dryer was squeaking a lot, so I purchased a new belt tensioner, but the original tensioner was an old-style no wheel tensioner, so that wasn't the source of the squeaking. I saw a lot of lint had built up inside the unit where there shouldn't have been that much. So I viewed a few videos on the Appliance Pros site and saw that the rear wheel guides were the cause of the squeaking and the rear felt drum and blower housing seal needed to be replaced. The rear blower housing was... Read more

• Little to no heat when broiling

DISCONNECT CIRCUIT BREAKER!!!. Remove oven door. Remove two screws that attach the element to the back of the oven, and two screws that secure element to the oven roof, then remove element. Had to be careful that the four wires don't slip into the back of the oven (difficult) to keep them from falling back as they are very short. Remove and replace element. I should have also detached the temp probe as it gets in the way and is easily broken off its flimsy mounting plate. The hardest part is... Read more

Personally I have experience working with electricity and knowing if I bought the part required this would be an easy fix. I got my model number and contacted Appliance Parts Pros and placed my order for the new elements, terminal blocks, and for appearance purposes 4 new Drip Pans. Excellent service and quick shipping. I ordered my parts on Sunday and received them on Tuesday. This was a simple repair that only required a screwdriver to remove the old terminal block from the range hood, wire... Read more

• Little to no heat when broiling
• Gas igniter glows, but will not light
• Little to no heat when baking
• Gas smell

Followed linked video instructions and replaced with new flat style Oven Igniter Kit. Some repair info background, while out shopping for a replacement oven ($1000 plus) a terrific salesman listened to the issue with my current oven and recalled his same issue and solution. I thanked him for his time and recommendation. I went home and searched "oven Ignitor" where I was led to this website. The video showed the same exact flat oven igniter and how easy it would be to replace it. I immediately... Read more

• Will not drain
• Pumps but will not spin
• Timer will not advance
• Doesn't shut off

The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more

Took out the old element and checked with olm meter determined bad, no continuity. Orded new Element from Appliance Parts Pros. Had new one in less than 2 days easy fix. Read more

• Won't start
• Element will not heat
• Little to no heat when baking

I determined the hidden bake element below the oven cavity was not working, because the bottom of the oven was cold during normal use. If you have a built-in microwave + oven combination (mine is KitchenAid Model No. KEMS308SSS05), this is a difficult repair. The engineer who designed this oven should be invited to succeed elsewhere. It is impossible to access the bake element from the inside of the oven, so the How To video associated with this part will not help you. I had to remove the... Read more

I first diagnosed the problem by replacing the burner control (Infinite switch) with one from a smaller burner (one that I knew worked fine). That seemed to solve the problem. I ordered the correct control for the big burner on Saturday night, it arrived Tuesday and installed it in less than 10 minutes using only a Phillips screwdriver. Remember to unplug the stove before performing any service. Take this time to clean around and under the stove. (You know it needs it!) Read more

• Oven not heating evenly
• Little to no heat when baking
• Element will not heat

The top part of our double wall oven quit working a couple years ago. We asked an appliance repair guy if he could find a replacement heating element and after a few days, he told us he couldn't. We switched to using the bottom and recently I started looking to purchase a new oven. On a whim, I decided to check the Interwebs and found several sites claiming to have the part that the appliance repair guy said didn't exist. I ordered from Appliance Parts Pros and a few days later the... Read more