By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
Need Help?
Call
Fix a dryer door that won't stay closed or requires multiple attempts to latch. This door strike latch secures the door during operation. Simple repair.
I followed the video on the parts page and had the part replaced in no time. My dryer door was slightly different than the example, but the concept was the same. My part arrived the next day and the repair took less than a half-hour. Extremely satisfied with this site Read more
Dryer won't start when you press the button? The start switch sends the signal to begin the cycle. Simple 5-10 minute fix with basic tools.
Two screws remove the top. Unplug the wires to the old relay, give it a quarter turn and it's out. A five minute procedure. What took five hours was replacing the dryer duct work that I discovered was mostly crushed on its way from the laundry room, through a couple of walls to the exterior. Read more
Dryer runs but won't heat or won't stop at cycle end? The timer controls heating element power and cycle completion. Moderate DIY repair, 30-45 minutes.
Used ohm meter on all thermostats and element.everything looked good.wasnt getting power to element unless you wiggled timer knob .ive used this website a bunch because it beats everyone else's prices Read more
Drive belt transfers motor power to rotate the drum. Replace when stretched, cracked, or broken to stop squealing and restore smooth operation. Confirm fit.
Purchased the items on your site . Did the job myself . Watched your helpful video. Read more
Includes screws and wire connectors. For the complete terminal block kit use 279320.
I ordered the parts through AppliancePartsPros.com. They were delivered the next day. I installed them and the dryer works great. Read more
Dryer not heating? A faulty heating element is often the cause. This part generates heat to dry clothes. DIY-friendly repair, takes 30-60 minutes.
Put in new part. It was done by maintenance personal and took just a few minutes. Read more
Freezer or fridge light not working? Door alarm going off? This door switch detects when doors open/close to control lights. Easy 15-minute fix.
Ordered the freezer door switch and the light. Replaced the freezer door switch and the light and everything is back to normal. Replaced both in less than 15 min with no problems. Read more
Dryer not heating or taking too long to dry? This heating element generates the hot air for drying cycles. DIY-friendly repair, typically 10-15 minutes.
Out with the old. In with the new. No problem. Dryers are simple and usually can be fixed quickly. appliance pros makes it easier with their tutorial videos and fast shipping! Read more
Dryer not heating or stuck on one temperature? This temperature selector switch controls heat settings. Moderate DIY repair with video guide available.
I replaced the cycle switch, fixing the lack of heat. The timer switch replacement fixed the auto cool down. I watched a cycle switch replacement on Youtube, demonstrating removal of the top console, which answered the only question I had about the repair. The timer switch was a hundred bucks. The only thing to be said about that is that it was a lot cheaper than a repairman or replacing the dryer. Read more
If your dryer won't heat properly or runs continuously without stopping, the timer may need replacement. Common DIY repair, moderate difficulty.
My husband took the old timer out and replace it with the new. Now it worked fine. Being we order the other parts we decided to replace them. Read more
Seals the gap between drum and bulkhead to maintain airflow and quiet operation. Replace when worn to eliminate squealing, reduce lint buildup, and prevent fabric snags. Confirm fit by model number.
New felt seal fit perfectly and it is like a new dryer Read more
Converting dryer from propane to natural gas? This orifice regulates gas flow in the burner assembly. Easy DIY fix, typically done in under 1 hour.
Confirmed parts needed through online chat with tech and followed video instructions for dryer conversion. Found a video online for range conversion. Replaced orifices for stove top and adjusted oven burner orifices and air shutters and inverted pin in pressure regulator to natural gas position. All went well with no problems, about an hour and a half to gather tools and complete both jobs. Probably could be done faster but I was taking my time. Read more
This cycling thermostat monitors the air temperature inside the dryer drum and signals the heating element to turn on and off to maintain the selected drying temperature. It is a small, disc-shaped component typically mounted on the blower housing or exhaust duct. Replace this thermostat if your dryer is not heating, overheating, running too cool, or shutting off before clothes are fully dry.
The Moisture Sensor is an OEM part for Whirlpool dryers. This part detects the moisture level in the clothing during the drying cycle, allowing the dryer to adjust the drying time accordingly.
Causes of a bad moisture sensor can include regular wear and tear, buildup of lint or residue, or physical damage.
Symptoms of a bad moisture sensor include:
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Viewed the video before I purchased the part. Received the part and put it in. Everything went as planned. Read more
The Door Handle is an OEM component for Whirlpool dryers. It provides convenient access to load and unload clothes through the dryer door opening.
Causes of a bad door handle can include normal wear and tear over extended use. Repeated clutching and releasing of the handle leads to fatigue of rubberized grip areas and loosening of mechanical connections. Accidental falls or impacts when transporting dry loads of clothes could also damage the handle structure or mounting.
Symptoms of a bad dryer door handle include:
Compatible models also include Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore dryers.
Separated oven door by removing screws. Inserted handle and secured with clips, and reassembledo door with screws provided. In served broiler handle and snappedal into place. Read more
Fix odd rattling noises or no airflow from vents with a new dryer blower wheel. Common issue: lint buildup or wheel separation. Moderate DIY repair.
It was a relatively easy fix - if you know how to take the dryer apart. If you don't, there are plenty of YouTube videos explaining how. Make sure you find your model. Since the wheel had separated from the nut, it wasn't quite as easy and holding the shaft and loosening the wheel. I had to remove (destroy) the wheel first. Then I was left with the nut on the shaft. The nut was seated on the shaft a lot tighter than I expected and took some force to get off. Once it was off, putting the new... Read more
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.