Whirlpool Range / Cooktop / Oven Parts

This line fuse protects the appliance's incoming power circuit by opening if an overload or short occurs. Replacing a blown fuse can help restore power once the underlying issue is corrected, preventing further damage to sensitive components.

• Interrupts line voltage when excessive current or a short circuit is detected
• Typical symptoms: unit completely dead, no display or interior lights, won't start or run
• Fuse tests open/no continuity with a multimeter when blown
• A blown fuse often points to another fault that must be addressed

• Disconnect power at the breaker/unplug before servicing; microwaves contain high-voltage parts that can retain a dangerous charge even when unplugged
• Replace only with the same type and rating as the original fuse
• Ensure the fuse seats firmly in its holders; do not bypass or jumper a fuse

This triple infinite surface element switch regulates power to a 3-size radiant burner on your cooktop. It lets you choose the small, medium, or large ring and adjust heat smoothly, restoring precise size selection and temperature control.

• Directs power to the inner, middle, and outer rings of a triple radiant surface element
• Cycles power to provide variable heat at the selected size
• Safe symptoms: burner won't change sizes or only one ring heats
• Safe symptoms: temperature stuck on high/low, won't turn off, or no heat

• Disconnect power before servicing
• Remove the knob/panel as needed; photograph wiring and transfer wires one at a time to matching terminals
• Secure the switch to the control panel, align the shaft, and reinstall the knob/panel
• Restore power and test all three element sizes across several heat settings

The knob is an OEM part for Whirlpool ranges. It provides an accessible interface for temperature and function selection via an easy to grip design. The knob allows for setting of temperature for the surface elements.

Causes of a bad knob can include wear and tear over time, exposure to excessive heat warping the surface, or accidental damage compromising integrity.

Symptoms of a bad knob include:

• Looseness, wobble or inability to secure firmly on the stem
• Faded or illegible markings limiting functionality
• Cracks or breaks that could be a hand safety hazard

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Replacement bake element for the lower oven. This is the primary heat source in Bake mode, restoring reliable preheats and even results when the original element fails. If your oven won't heat or underbakes, this part addresses the issue.

• Provides radiant heat from the bottom of the oven during Bake mode
• Common failure symptoms: no heat in Bake, won't reach set temperature, or visible breaks/blistering on the element
• Restores even baking and consistent preheat performance when replaced
• Often tests open (no continuity) when the original element is burned out

• Disconnect power at the breaker or unplug the appliance before servicing
• Remove oven racks, then the element's mounting screws; gently pull the element forward to access wires
• Support wires so they don't retract; disconnect the two spade terminals and transfer any mounting bracket from the old element if needed
• Attach terminals to the new element, tuck wires carefully, reinstall screws, restore power, and test Bake

The Burner Knob is an OEM part designed for Whirlpool ranges. It fits onto the burner control valve, allowing you to adjust the flame level and temperature while cooking.

Color: Black

Burner knobs can suffer damage or malfunction due to regular use, accidental impacts, or heat exposure over time. These conditions can cause the knob to crack, become loose, or stop rotating smoothly.

Symptoms of a faulty burner knob include:

• Difficulty adjusting the burner flame level
• Knob slipping or not turning smoothly
• Knob falling off or feeling loose
• Burner not responding accurately to knob adjustments

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This surface burner grate kit restores a level, stable cooking surface on your gas cooktop or range. Replace worn or damaged grates to improve pot stability, maintain proper flame clearance, and refresh the look of your appliance.

• Supports pots and pans above the burners at the correct height for efficient, even heating
• Provides a stable, level surface to help prevent cookware from rocking or tipping
• Replace if grates are cracked, warped, heavily chipped, or the finish is excessively worn
• Helps protect the cooktop surface from direct cookware contact

• Turn all burners off and allow the cooktop and existing grates to cool completely before handling
• Lift off old grates; clean the cooktop surface before installing new parts
• Set new grates in place, ensuring they sit flat and align properly over each burner
• Do not drop or slam grates; heavy cast components can chip or crack if impacted

This surface heating element restores dependable heat on your electric range or cooktop. Replace a failed top burner to regain consistent boiling and simmering performance when one position stops heating, heats unevenly, or cycles unpredictably.

• Converts electrical power into heat for cookware on the cooktop
• Replaces a burned-out/open surface burner to restore normal operation
• Helps fix: no heat, intermittent heat, or uneven heating at a burner position
• Matches the original footprint and connections for proper fit and function

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the cooktop to cool completely; wear appropriate hand and eye protection
• Access the element per your service manual; note wire locations and transfer any mounting clips/brackets from the old part if present
• Seat terminals fully and secure the element before reassembly; test on low and high settings

The Grate-Kit is an OEM component designed specifically for Whirlpool kitchen ranges. This kit contains the replacement grates that sit atop the burner elements. The grates are responsible for providing an even cooking surface while elements are in use. 

Causes of bad grates can include warping, discoloration, or pitting due to continuous high heat exposure over time. Thin or warped grates may no longer distribute heat evenly across pans.

Symptoms of bad grates include:

• Uneven or inefficient cooking 
• Food burning more easily
• Visible wear like scratches or pits on cooking surface
• Grates that are loose, wiggly, or difficult to remove

 This replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This oven door hinge is a replacement for many models of ovens. Oven doors will have two hinges. If there is a problem with one or both of the hinges, it means that the door will not open and close properly. It might not stay closed, or it could be difficult to open. This would make it impossible to use the oven, and the hinge should be replaced as soon as possible.An oven door hinge could become damaged for a host of reasons. When the door is open, too much pressure could be placed on the hinge, which could cause it to break. It could become corroded over time, or the spring might wear down. When there are issues, the owner will want to replace the hinge to ensure the door stays closed. Owners should always make sure the oven is off and not powered before beginning work.The oven door hinge will work with certain models of ovens from Whirlpool, Maytag, Amana, Jenn-Air, Norge, Crosley, and Magic Chef. This is a genuine OEM replacement part, and it is sold individually. If both of the hinges need to be replaced, the owner will need to buy two.

This hinge is for painted door only. For stainless steel door use WP8272822.

This oven door gasket forms the heat-resistant seal between the door and oven cavity. Replacing a worn seal helps the oven reach and maintain temperature, reduces heat loss around the door, and supports even, consistent baking performance.

• Creates a continuous seal between the oven door and frame to contain heat and moisture
• Helps maintain accurate temperatures and normal preheat times
• Replaces torn, frayed, flattened, or brittle seals that allow heat to escape
• Common symptoms include hot air leaking near the door, uneven baking, and longer cook times

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Open the door and remove the old gasket, noting clip/pin locations and orientation
• Press the new gasket evenly into the retaining channel or holes; do not stretch the seal
• Close the door and verify uniform contact around the frame for a snug seal

This 8-inch coil surface element restores reliable heating on the large burner of electric ranges and cooktops. Its 2350-watt design provides steady, even heat for boiling, frying, and everyday cooking.

• Converts electrical power into heat for the large cooktop position
• Common failure symptoms: no heat, uneven heating, only part of the coil glowing, visible breaks or blisters, or failed continuity
• Plug-in coil style for receptacle-type burner sockets
• If no heat persists after replacement, also inspect the element receptacle and the burner switch

• Disconnect power to the range/cooktop and allow the element to cool completely
• Lift the old element and pull straight out from the receptacle
• Align the new element's terminals with the receptacle, push in firmly until fully seated, and set it into the support/drip bowl
• Restore power and test the burner

This terminal block provides an insulated, secure junction for incoming power or harness leads inside the appliance. Replacing a cracked, loose, or heat-damaged block restores a safe, reliable connection and helps prevent arcing or intermittent power.

• Creates a fixed, insulated junction between external supply wires and internal appliance wiring
• Maintains tight screw-lug connections to minimize resistance and heat buildup
• Helps ensure steady power delivery to controls, motors, and heaters
• Common indicators of failure: melted/discolored block, burning odor, visible arcing, loose or stripped terminals, intermittent or no power

• Disconnect power at the breaker and verify zero voltage before servicing
• Photograph/label wire positions; transfer one lead at a time to the new block
• Tighten terminal screws firmly; do not overtighten into the insulator
• Inspect wire ends/ring terminals and strain relief; replace any heat-damaged components per the service information

This fan motor powers the cooling fan that moves air through your unit. Replacing a worn or noisy motor restores proper airflow to help maintain stable temperatures and reliable performance. What it does:

• Drives the fan blade to circulate air for cooling and temperature control
• Helps prevent component overheating caused by weak or stalled airflow
• Fixes: fan not running or starting intermittently
• Fixes: loud humming, grinding, or rattling from the fan area
• Fixes: longer run times or warm spots due to poor airflow

• Includes: 1 fan motor

• Disconnect power before servicing; allow moving parts to stop
• Note wire positions and motor orientation; take a photo for reference
• Transfer the existing fan blade and mounting hardware as needed
• After install, ensure the fan spins freely and no wiring contacts moving parts before restoring power

This light socket holds the bulb and supplies power for reliable appliance lighting. Replace a cracked, heat-damaged, or loose socket to restore safe, consistent illumination inside the appliance.

• Secures the lamp and connects it to the appliance wiring
• Restores proper electrical contact to the bulb
• Replaces sockets showing arcing, discoloration, melting, or a loose fit
• Common symptoms: light won't turn on, flickers, works intermittently, or bulbs fail prematurely

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the appliance to cool completely before accessing the socket
• Use the bulb type and wattage specified for your model
• Transfer existing mounting screws/brackets and wiring connectors as needed; ensure tight, clean connections

This door latch keeps the door securely closed and engages the door switch/interlock so the appliance operates as designed. Replacing a worn or broken latch helps resolve door-related errors and restores reliable, safe operation.

• Secures the door against the strike for proper closure and alignment
• Actuates the door switch/interlock so controls recognize a closed door
• Helps prevent operation when the door is open or not fully latched
• Common symptoms: door won't latch or stay closed; unit won't start or shows a "door/open-close" message; broken or loose latch hook

• Disconnect power before servicing; use proper PPE and beware of sharp edges
• Access the latch through the door panel/trim as applicable; use non-marring tools to avoid damage
• Transfer any reusable clips/springs from the old latch to the new part
• After installation, verify smooth door closure and that the control detects the door as closed