Whirlpool Washer Parts

Fix a broken or missing dispenser drawer handle that makes it hard to open your washer's detergent compartment. Simple snap-in installation in minutes.

Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.

This three-circuit connector housing organizes and protects terminals in an appliance wiring harness. It provides a secure, insulated plug connection to help prevent loose contacts, heat damage, and intermittent operation when the original housing is cracked or melted. What it does:

• Holds three wiring terminals in the correct orientation for a mating connector
• Insulates and locks terminals to reduce arcing and overheating at the plug
• Replaces cracked, brittle, or heat-damaged connector housings
• Symptoms can include intermittent power, burnt odor near the connector, discoloration/melting, or a plug that won't stay latched

• 1 three-circuit connector housing

• Disconnect power before servicing the appliance
• Note wire/terminal positions and transfer them one at a time into the new housing
• Inspect terminals; replace any that are discolored, loose, or damaged. Use the correct crimp tool/terminals specified for your model
• Fully seat each terminal until it locks and the connector latch engages securely

Washer won't advance cycles or stops mid-cycle? Timer controls cycle progression. DIY repair if timer knob doesn't advance washing stages properly.

If your washer agitator spins freely or clothes aren't agitating properly, this assembly restores the back-and-forth motion. DIY repair in 10-30 minutes.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Fix washer won't drain issues with this lower wiring harness. Restores electrical connections between drain pump and control components.

This is a white plastic handle that attaches to the front of the washer's detergent dispenser drawer, allowing you to pull it open to add detergent, bleach, or fabric softener. Replace this handle if it is cracked, broken, or has snapped off, making it difficult to open the dispenser drawer.

Suspension rod ball and bushing kit with 4 balls and 4 bushings. Replaces worn or broken suspension components that cause washer movement and noise.

Adjustable leveling foot threads into washer or dryer base to stabilize appliance on uneven floors. Replace if cracked, worn, or missing to reduce rocking.

Inner door panel insert for front-load washer door assembly. Provides structural support and finished interior surface. Replace if cracked or damaged.

Washer won't fill properly or overfills? This water level pressure switch senses fill levels and signals when to stop. Easy DIY fix for cycle timing issues.

Replaces a cracked, worn, or loose timer dial skirt that causes knob wobbling. Restores secure knob fit and proper alignment on the timer control opening.

This is the fabric softener dispenser cup that fits inside the agitator or dispenser housing of a top-load washing machine. It holds liquid fabric softener and releases it into the wash water at the appropriate time during the rinse cycle. Replace this cup if it is cracked, warped, or clogged, or if fabric softener is not dispensing properly during the wash cycle.

Washer water heater element raises water temperature during wash cycles. Replace if cracked, corroded, or no longer heating properly in your machine.

Replace a cracked or broken dispenser cover that exposes internal parts. This outer trim panel protects wiring and restores appearance. Easy hand removal.